Panduit E6212B1 User manual

Brand: Panduit

Model: E6212B1

Category: Racks

Type: User manual

This manual is also suitable for

Panduit E6212B1 is an Enterprise Network Cabinet, designed to house and protect your valuable network equipment. It comes with a range of features that make it easy to install and maintain your equipment, and to keep it organized and secure.

The E6212B1 has adjustable equipment rails, so you can customize the layout to fit your specific needs. It also has overhead cable openings, so you can easily route cables without having to worry about tangles or clutter. The front and rear doors are removable, so you can easily access your equipment, and the side panels are lockable, so you can keep your equipment secure.

STOP

READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE

REMOVING CABINET FROM SKID

CM646

INSTRUCTIONS CM646

FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp

Page 2 of 10

Enterprise Network Cabinets

(E6212B1, E6412B2 - Server Configured

)

NOTE - Some views in this document may vary

slightly from your actual cabinet configuration.

Tool List:

-22mm wrench

-10mm wrench

-13mm socket wrench

-T30 Torx bit (included with cabinet configuration)

-Wire Cutter

INSTRUCTIONS CM646

For Technical Support: www.panduit.com/resources/install_maintain.asp

General Cabinet Operation Page

Packaging Material Removal……………………………………………...…………… 4

Leveling…………………………..……………………………………………………

…

Grounding……………………………………………………………………………… 6

Equipment Rail Adjustment……………………………………………………………

…

Overhead Cable Openings……………………………………………………………

…

Front & Rear Doors (Removal and Installation) ………………………………………

…

Side Panels (Removal and Installation) ………………………………………………

…

Table of Contents

Page 3 of 10

INSTRUCTIONS CM646

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 4 of 10

Packaging Material Removal

Before removal of packaging material:

Check tip indicator on the outside of cabinet to ensure cabinet was shipped in the upright position. If tip indicator shows improper handling,

inspect cabinet for damage before accepting cabinet.

Before handling cabinet:

Small glide strips are installed at various locations around the cabinet to protect the cabinet’s finish during shipping. These strips are to be

removed prior to handling of cabinet.

REMOVAL INSTRUCTIONS

• Remove all stretchwrap and protective cardboard from outside of cabinet

• Remove [2] Shipping Hold Down Brackets at front and rear of cabinet

• Use

[2] people to carefully lift and remove cabinet from pallet

Pallet

Note: Doors, Side panels, and other components are removed for clarity.

IMPORTANT:

Leveling Legs must be fully retracted before the cabinet is moved into place. Sliding cabinet on leveling legs may

result in damage to the leveling legs. (Leveling Legs ship in retracted position)

[2] Shipping

Hold Down

Brackets

[6] M6 Torx Screws

(use T30 Torx bit)

[4] Lag Screws and Washers

(use 13mm socket wrench)

INSTRUCTIONS CM646

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 5 of 10

Front-to-Back Cabinet Leveling

Side-to-Side Cabinet Leveling

Leveling

• Ensure that [4] Leveling Legs are fully retracted

• Slide Cabinet into final position

• Lower the [4] Leveling Legs until the cabinet weight is fully supported

• Adjust the [4] Leveling Legs so that the cabinet is level front-to-back and side-to-side

[4] Leveling Legs

(use 22mm Wrench)

INSTRUCTIONS CM646

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 6 of 10

[8] Grounding Lug Locations

(Front and Rear of Beams)

Grounding

• Attach Grounding Lug or Grounding Bar at any of the [2] location(s) shown below

• Grounding location is indicated by universal ground symbol

• Use M5 bonding screw

INSTRUCTIONS CM646

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 7 of 10

Equipment Rail Adjustment

• Remove [4] Torx screws and [4] hex nuts per equipment rail

• Move equipment rail to desired positon

• Secure equipment rail to cabinet with[4] Torx screws and [4] hex nuts per rail

• NOTE: Front equipment rails are integral to the cabinet frame and are in a fixed position

[2] M6 Torx Screws

(use T30 Torx bit)

[2] Hex Nuts

(use 10mm wrench)

[2] M6 Torx Screws

(use T30 Torx bit)

[2] Hex Nuts

(use 10mm wrench)

INSTRUCTIONS CM646

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 8 of 10

Overhead Cable Openings

• Cut [4] tabs with wire cutter to open each cable opening - OPTIONAL

OPTIONAL

[2] 40mm x 131mm Openings

[1.57” x 5.15”]

INSTRUCTIONS CM646

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 9 of 10

Front & Rear Doors (Removal and Installation)

• Open Door(s) to approximately 90º

• Lift Door(s) up and pull away from cabinet frame

• REVERSE STEPS to install Front & Rear Doors

INSTRUCTIONS CM646

For Instructions in Local Languages

and Technical Support:

www.panduit.com/resources/install_maintain.asp

E-mail:

[email protected]

Phone:

866-405-6654

www.panduit.com

Page 10 of 10

Side Panels (Removal and Installation)

• Unlock side panel

• Pull top of side panel away from cabinet frame

• Lift bottom tabs out of cabinet frame

• REVERSE STEPS to install Side Panel

Side Panel Tabs

Panduit E6212B1 User manual

Brand: Panduit

Model: E6212B1

Category: Racks

Type: User manual

This manual is also suitable for

Download PDF

report

Panduit E6212B1 User manual

This manual is also suitable for

Panduit E6212B1 User manual

Related papers

Other documents