SoundCraft Si Performer Owner's manual

®

User Guide v2.0

For Soundcraft Si Performer 1, 2 & 3

Incorporating Software version 1.6

®

User Manual

INFORMATION

IMPORTANT

Please read this manual carefully before using your mixer

for the rst time.

This equipment complies with the EMC directive 2004/108/EC and LVD 2006/95/EC.

This product is approved to safety standards:

IEC 60065:2005 (Seventh Edition) +A1:2005

EN60065:2006 +A1:2006 +A1:2008

UL60065 2012 7th Edition

CAN/CSA-E60065-03 + A1: 2006

And EMC standards

EN55103-1: 2009 (E2)

EN55103-2: 2009 (E2)

Warning: Any modication or changes made to this device, unless explicitly approved by Harman, will

invalidate the authorisation of this device. Operation of an unauthorised device is prohibited under Section

302 of the Communications act of 1934, as amended, and Subpart 1 of Part 2 of Chapter 47 of the Code of

Federal Regulations.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

* Reorient or relocate the receiving antenna

* Increase the separation between the equipment and the receiver

* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

* Consult the dealer or an experienced radio/TV technician for help.

For further details contact: Harman International Industries Ltd, Cranbourne House, Cranbourne Road, Potters Bar,

Hertfordshire EN6 3JN, UK. Telephone +44 (0)1707 665000 Fax: +44 (0)1707 660742 email: [email protected]

Parts of the design of this product may be protected by worldwide patents.

Part No. 5023012-01

Rev 1.0

E&OE September 2014

Soundcraft is a trading division of Harman International Industries Ltd. Information in this manual is subject to change

without notice and does not represent a commitment on the part of the vendor. Soundcraft shall not be liable for any

loss or damage whatsoever arising from the use of information or any error contained in this manual. No part of this

manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic,

electrical, mechanical, optical, chemical, including photocopying and recording, for any purpose without the express

written permission of Soundcraft.

Harman International Industries Limited

Cranborne House, Cranborne Road, Potters Bar, Hertfordshire, EN6 3JN, UK

Tel: +44 (0)1707 665000

Fax: +44 (0)1707 660742

http://www.soundcraft.com

CONTENTS

1.0 AN INTRODUCTION TO Si PERFORMER

1.1: Safety

1.2: Warranty

 1.3:Specications

2.0: GETTING STARTED

2.1:ConsoleOverview

 2.2:PartsOfTheConsole

 2.3:FaderGlow

3.0: ASSIGNABLE CONTROLS

3.1:FaderLayers

3.2:ControlChannels

 3.2.1:ControlChannelAssignment

3.3:GlobalModeEncoders

3.4:AssignableChannelStrip

3.5:tOTEM(FaderFollow)

4.0: TOUCH SCREEN OPERATION

 4.1:MainMenu

5.0: INPUTS & OUTPUTS

 5.1:Patching

  5.1.1:SoundwebPatching/Control

 5.2:DefaultPatching

 5.3:ViSiConnectI/O(OptionCards)

  5.3.1:OptionCards

  5.3.2:Stageboxes

6.0: CHANNELS & BUSSES

 6.1:InputChannels

  6.1.1:InputSetup

 6.2:MixOutputs

  6.2.1:MixOutputsSetup

 6.3:MatrixOutputs

  6.3.1:MatrixOutputsSetup

 6.4:MainMixOutputs

  6.4.1:MainMixOutputsSetup

 6.5:FXBusses

7.0: DSP Elements

 7.1:FunctionFocus

 7.2:ACS/ChannelStripElements

  7.2.1:ACSInput

  7.2.2:ACSGate

  7.2.3:ACSCompressor

  7.2.4:ACSEqualiser

  7.2.5:ACSOutput

 7.3:ControlChannel

 7.4:GraphicEQ(GEQ).

8.0: MIX FEATURES

 8.1:MuteGroups

 8.2VCAGroups

 8.3:CopyAndPaste

 8.4:AudioInterrogate

 8.5:SoloSystem

 8.6:Monitoring

 8.7:CLR&ALT+CLR

9.0: SHOWS, CUELISTS, AND SNAPSHOTS

 9.1:Shows

 9.2:Cuelist&Snapshots

  9.2.1:EditCue

10.0: LEXICON FX

 10.1:Reverbs

  10.1.1:ReverbParameters

 10.2:Delays

  10.2.1:DelayParameters

 10.3:MiscFX

  10.3.1:MiscFXParameters

11.0: PREFERENCES, SYSTEM, SECURITY

 11.1:Preferences

 11.2:SystemSettings

 11.3:SecuritySettings

  11.3.1:Add/EditUser

  11.3.2:Proles

 11.4:SoftwareUpdates

 11.5:ResetConsole

12.0: OSCILLATOR

13.0: DMX - LIGHTING CONTROL

APPENDIX 01: NO SOUND?

ATroubleShootingGuide.

For clarity, this manual uses section references rather than page numbers.

In some instances, one section reference may extend to several pages.

UserManual

User Manual

1.0: INTRODUCTION

INTRODUCTION TO PERFORMER

1.0: WELCOME TO PERFORMER

The Soundcraft Si Performer is a compact digital console optimised for live sound. It is designed

to be powerful, yet simple to use, with intuitive controls, consistent colour-coded feedback, and

rapid parameter access. Features such as motorised faders, the Assignable Channel Strip (ACS),

tOTEM Fader Follow buttons, VCAs, and incorporated DMX512 control mean that any aspect of

the performance can be served to the surface in an instant, with analogue-style control of its

comprehensive feature-set.

• Recallable GB mic inputs with locking

connectors and phantom power indicators.

• 8 Balanced-Jack line ins, 16 XLR analogue line outs, AES

in and out, Wordclock, MIDI, Headphones out.

• DMX port for integrated lighting control with four dedicated

control layers.

• HiQnet Ethernet Port and compatibility (Venue Events,

Soundweb Control).

• 64 x 64 and 64 x 56 option card slots, fully compatible with all

ViSi Connect series cards and Soundcraft Stageboxes.

• Up to 80 channels to mix (64 Mono input channels,

8 Stereo input channels).

• Soundcraft 4-band British EQ on all inputs and outputs.

• Soundcraft Dynamics available on all channels.

• Delay available on all channels.

• BSS™ Graphic EQ on all Mix, Matrix, and Main Bus Masters.

• Quad Lexicon™ FX processors.

• Fader Glow™ illumination on all faders for at-a-glance

display of current fader function.

• D.O.G.S. (Direct Out Gain Stabiliser) technology.

• tOTEM™ (The One Touch Easy Mix) system for ‘Fader

Follow’ functionality for all Mix, Matrix, and FX Send busses -

create mixes quickly

and easily.

• Assignable Control Strip (ACS)

for instant access to all channel

parameters.

• Colour touch screen interface for patching, routing, show set-

up and security settings.

• Versatile Global Mode Encoders for exible control.

• Comprehensive Show, Snapshot, and Cuelist system with

USB storage.

• 4 user-assignable fader layers.

• 4 Matrix mixes that can operate in mono or stereo.

• 14 Aux-style Mix Busses, 6 of which can operate in mono or

stereo.

• 8 Mute Groups.

• 8 VCA Groups

• Comprehensive input, output, gain reduction and status me-

tering/monitoring.

• Independent Main Mono/Centre and Left/Right busses.

• Ultra hard-wearing, polycarbonate-covered control

surface resists wear and tear.

• 12V Lamp Connector.

User Manual

1.1: SAFETY

INTRODUCTION > SAFETY

1.1: INTRODUCTION > SAFETY

THIS UNIT MUST BE EARTHED

Under no circumstances should the mains earth be disconnected from the mains lead.

The wires in the mains lead are coloured in accordance with the following code:

Earth: Green and Yellow (Green/Yellow - US)

Neutral: Blue (White - US)

Live (Hot): Brown (Black - US)

As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals

in your plug, proceed as follows:

The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the

letter E or by the earth symbol.

The wire which is coloured Blue must be connected to the terminal in the plug which is marked with the letter N.

The wire which is coloured Brown must be connected to the terminal in the plug which is marked with the letter L.

Ensure that these colour codings are followed carefully in the event of the plug being changed.

This unit is capable of operating over a range of mains voltages as marked on the rear panel.

The internal power supply unit contains no user serviceable parts. Refer all servicing to a qualied service

engineer, through the appropriate Soundcraft dealer.

SAFETY NOTICES

For your own safety and to avoid invalidation of the warranty

please read this section carefully.

Important Symbols

Headphones Safety Warning

Contains important information

and useful tips on heaphone

outputs and monitoring levels.

Warnings

Alerts the user to the presence of uninsulated

‘dangerous voltage’ within the product’s

enclosure that may be of siufecient magnitude

to constitute a risk of electric shock to persons.

Notes

Contain important information

and useful tips on the operation

of your equipment.

Cautions

Alerts the user to the presence of important

operating and maintenance (servicing)

instructions in the literature accompanying

the appliance.

User Manual

1.1: SAFETY

INTRODUCTION > SAFETY

1.1: INTRODUCTION > SAFETY

WARNINGS

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Clean the apparatus only with a dry cloth.

• Do not install near any heat sources such as radiators, heat resistors, stoves, or other apparatus

(including ampliers) that produce heat.

• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

• Do not use this apparatus near water.

• Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two

blades with one wider than the other. A grounding type plug has two blades and a third grounding

prong. The wide blade or the third prong are provided for your safety. When the provided plug does not

t into your outlet, consult an electrician for replacement of the obsolete outlet.

• Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles and the point where they exit from the apparatus.

• Only use attachments/accessories specied by the manufacturer.

• Unplug this apparatus during lightning storms or when unused for long periods of time.

• Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been

damaged in any way such as power-supply cord or plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate

normally, or has been dropped.

• Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the

apparatus. When the cart is used, use caution when moving the cart/apparatus combination to avoid

injury from tip-over.

• No naked ame sources, such as lighted candles or cigarettes etc., should be placed on the

apparatus.

• No user serviceable parts. Refer all servicing to a qualied service engineer, through the

appropriate Soundcraft dealer.

• It is recommended that all maintenance and service on the product should be

carried out by Soundcraft or its authorised agents. Soundcraft cannot accept any

liability whatsoever for any loss or damage caused by service, maintenance or repair

by unauthorised personnel.

• WARNING: To reduce the risk of re or electric shock, do not expose this

apparatus to rain or moisture. Do not expose the apparatus to dripping or splashing

and do not place objects lled with liquids, such as vases, on the apparatus. No

naked ame sources, such as lighted candles, should be placed on the apparatus.

• Ventilation should not be impeded by covering the ventilation openings with items

such as newspapers, table cloths, curtains etc.

User Manual

1.1: SAFETY

INTRODUCTION > SAFETY

1.1: INTRODUCTION > SAFETY

WARNINGS

ADVICE FOR THOSE WHO PUSH THE BOUNDARIES

Although your new console will not output any sound until you feed it signals, it has the

capability to produce sounds which, when monitored through an amplier or headphones,

can damage hearing over time.

Please take care when working with your audio — if you are manipulating controls which

you don’t understand (which we all do when we are learning), make sure your monitors are turned

down. Remember that your ears are the most important tool of your trade, look after them, and they will

look after you.

Most importantly — don’t be afraid to experiment to nd out how each parameter affects the sound —

this will extend your creativity and help.

NOTE: The packaging, in which your console arrived, forms part of the product and must

be retained for future use.

NOTE: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct the inter-

ference at his own expense.

This Class A digital apparatus meets the requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numérique de la Classe A respecte toutes les exigences du Règlement sur le matériel

brouilleur du Canada.

User Manual

1.2: WARRANTY

INTRODUCTION > WARRANTY

1.2: INTRODUCTION > WARRANTY

WARRANTY

1 Soundcraft is a trading division of Harman International Industries Ltd.

End User means the person who rst puts the equipment into regular operation.

Dealer means the person other than Soundcraft (if any) from whom the End User purchased the Equipment, pro-

vided such a person is authorised for this purpose by Soundcraft or its accredited Distributor.

Equipment means the equipment supplied with this manual.

2 If within the period of twelve months from the date of delivery of the Equipment to the End User it shall prove

defective by reason only of faulty materials and/or workmanship to such an extent that the effectiveness and/or

usability thereof is materially affected the Equipment or the defective component should be returned to the Dealer

or to Soundcraft and subject to the following conditions the Dealer or Soundcraft will repair or replace the defec-

tive components. Any components replaced will become the property of Soundcraft.

3 Any Equipment or component returned will be at the risk of the End User whilst in transit (both to and from the

Dealer or Soundcraft) and postage must be prepaid.

4 This warranty shall only be available if:

a) The Equipment has been properly installed in accordance with instructions contained in Soundcraft’s manual.

b) The End User has notied Soundcraft or the Dealer within 14 days of the defect appearing; and

c) No persons other than authorised representatives of Soundcraft or the Dealer have effected any replacement

of parts maintenance adjustments or repairs to the Equipment; and

d) The End User has used the Equipment only for such purposes as Soundcraft recommends, with only such

operating supplies as meet Soundcraft’s specications and otherwise in all respects in accordance Soundcraft’s

recommendations.

5 Defects arising as a result of the following are not covered by this Warranty: faulty or negligent handling, chem-

ical or electro-chemical or electrical inuences, accidental damage, Acts of God, neglect, deciency in electrical

power, air-conditioning or humidity control.

6. The benet of this Warranty may not be assigned by the End User.

7. End Users who are consumers should note their rights under this Warranty are in addition to and do not affect

any other rights to which they may be entitled against the seller of the Equipment.

User Manual

1.3: SPECIFICATIONS

INTRODUCTION > SPECIFICATIONS

1.3: INTRODUCTION > SPECIFICATIONS

Si EXPRESSION TYPICAL SPECIFICATIONS

• Frequency Response

- Mic / Line In to any Output: +/-1.5dB, 20Hz-20kHz

• T.H.D.

- Mic Sensitivity -30dBu < 0.01% @ 1kHz

• Noise

- Residual noise -86dBu

- Mic Input E.I.N. 22Hz - 22kHz, Unweighted. (max gain)

-126dBu (150Ω source)

- Mix noise, masters at unity < -86dBu

- 1 input to mix at unity gain -84dBu

- CMRR mic @1KHz (max gain) -80dBu

• Crosstalk (@ 1kHz)

- Channel ON attenuation <120dB

- Channel Fader attenuation <120dB

- Mic – Mic -100dB @ 1KHz, -85dB@10kHz

- Line – Line -100dB @ 1KHz, -85dB@10kHz

• Input Gain

- Mic Gain -5dB – 58dB integrated pad design, 1dB steps

- Line Trim -10dB - +16dB

• Gate

- Threshold -60dBfs - -6dBfs

- Depth -60dB - -3dB

- Attack 0.1ms – 200ms

- Release 20ms – 500ms

- Side-chain HPF 22Hz – 2.5kHz

- Side-chain LPF 160Hz – 20kHz

• Compressor

- Threshold -52dBfs - -6dBfs

- Ratio 1:1 – 20:1

- Attack 0.1ms – 200ms

- Release 5ms – 900ms

- Makeup Gain 0dB – 24dB

• EQ

- All Bands 22Hz – 20kHz, +/-15dB Q 6-0.3

- Shelf (HF) 800Hz – 20kHz, +/-15dB

- Shelf (LF) 20Hz – 500Hz, +/-15dB

- HPF 40Hz – 1kHz

• Delay

- User adjustable delay 1sample – 500ms

- GEQ 31Hz – 16kHz 1/3 octave

• GEQ

- 31Hz – 16KHz 1/3 octave

• Digital I/O

- AES Sample rate converter range 8kHz – 200kHz

- External Word Clock In range 48kHz +/-7Hz (internal

systems), +/-3Hz with stageboxes.

- Word clock out jitter +/- 7ns

- Analogue out for 0dBfs +21.5dBu

- Converter resolution 24-bit

- DSP resolution 40-bit oating point

• Latency

- Mic In to Line Out <0.8 ms

- Analogue in to AES out <0.6 ms

- AES in to Line Out <0.8ms

- AES in to AES out <0.5ms

- Stagebox Mic In to Stagebox <0.9mS

• Input & Output Levels

- Mic Input +22dBu max

- Line Input +22dBu max

- Mix Output +21.5dBu max

- Headphones (@150Ω) 300mW (recommended

impedance 75 to 200Ω)

• Input & Output Impedances

- Mic Input 3kΩ

- Line Input 10kΩ

- AES Input 110Ω

- Outputs 150Ω (balanced), 75Ω (unbalanced)

- Word Clock used as Output 50Ω

- Word Clock used as Input 4K7Ω

- AES Output 110Ω

- DMX 120Ω

• USB

- Max current 200mA

• Lamp Output

- 12v DC 100mA max (per socket)

• Power

- Consumption (typical) <130w Si EXPRESSION 3

- AC Input voltage range 88-264VAC auto sensing

- AC Frequency range 47-63Hz

• Operating Conditions

- Operating Temperature Range 5°C to 45°C

- Humidity 0%-90%, non condensing Ta=40°C (104°F)

- Storage Temperature Range -20°C to 60°C (-4°F to

140°F)

E & OE.

Soundcraft reserves the right to change specications without notice.

User Manual

2.0: GETING STARTED

STARTING OFF - AN INTRODUCTION TO THIS MANUAL

2.0: GETTING STARTED

Anyone with minimal audio experience should be able to operate the Si Performer console without

reading too much of this manual, though we do recommend you take the time to go through it.

An excellent place to start would be the feature list on the introductory page (chapter reference 1.0),

which will familiarise you with all of the main possibilities, facilities, and functions.

Please note: Most of the illustrations in this manual are based on the Si Performer 2 model. Where

there are fundamental differences between operation of Si Performer 1, 2, and 3, it is noted in the

relevant section.

PDF

If you’re reading the PDF version of the manual, you can use the thumbnail view and links from the

Contents page to navigate quickly.

User Manual

2.1: OVERVIEW

GETTING STARTED > OVERVIEW

2.1: GETTING STARTED > OVERVIEW

Si Performer consoles offer an incredible amount of exibility and ease-of-use for their

relatively compact size. To achieve this, there are several assignable features it is advisable you

understand before using the console for performance.

Assignability

The Assignable Channel Strip (ACS) and Global Mode Encoders are relatively straight forward and

work in conjunction with the Select (SEL) Control Channel buttons and the Encoder Mode buttons.

Essentially, assignability means that one button can assign a function to many other buttons.

For example, pressing a Control Channel SEL button assigns that channel’s entire channel strip and

associated controls to the Assignable Channel Strip (ACS) section. In this way, the ACS can take

the place of many sets of repeated controls.

In addition, the console has 14 Mix busses, four stereo Matrix busses, and four internal FX send

busses, most conveniently accessed with the tOTEM (FADER FOLLOW) controls, which assign

bus control to the console faders.

For full detail on the Si Performer’s assignable controls, please see section 3.

Also note that the MIX 1-14 Busses and Bus masters serve the same function as Auxiliary Mix bus-

ses and masters.

Physical I/O, DSP Channels, Control Channels

Because the console has inputs and outputs that can be patched anywhere, and DSP channels that

can be controlled by any Control Channel, these elements are considered separate in this manual.

Section 5 deals with the console’s patching system, which connects physical inputs and outputs to DSP chan-

nels. Section 6 deals with DSP channels (Input Channels, Mix busses and masters, and so on),

routing, and channel-type-specic settings. Section 7 deals with the assignable control channels (console

surface controls) and the channel processing elements

that they control.

Section 8 (Mix Features) deals with console

performance functions that sit outside the

assignable channel structure, such as Mute Groups,

VCA Groups, Copy And Paste, the interrogation

function, the Solo system, and so on.

Touch Screen

The console Touch Screen has a simple, one-layer

menu structure. The main menu is the default screen

and can always be accessed by pressing the MENU button next to it. The Main Menu options are clearly

labelled and lead to simple menus or special functionality, such as a QWERTY keyboard for text input etc.

Please see Chapter 4 for more detail on the Main Menu options. The individual Menus themselves are dealt with

in the relevant chapter references (For example, the INPUTS menu is dealt with in the Input Channels

reference).

Power

The Si Performer incorporates a safety feature to prevent accidental shut-down. To shut down the console press

and hold the POWER key for at least two seconds (it will ash orange) then press it again to conrm the pow-

er-down action. If you don’t press power key the second time, it will revert to a steady green state and you will

have to go through the process again to shut down.

User Manual

2.2: PARTS OF THE CONSOLE

GETTING STARTED > PARTS OF THE CONSOLE

2.2: GETTING STARTED > PARTS OF THE CONSOLE

User Manual

2.2: PARTS OF THE CONSOLE

GETTING STARTED > PARTS OF THE CONSOLE

2.2: GETTING STARTED > PARTS OF THE CONSOLE

User Manual

2.3: FADERGLOW

GETTING STARTED > FADERGLOW

2.3: GETTING STARTED > FADERGLOW

Soundcraft FaderGlow™ is a unique feature that gives the user an additional level of status

indication, and can signicantly reduce operating errors.

Several different functions can be assigned to the console faders, so it can be easy to lose track of which

function is currently being controlled, especially when grabbing a fader in a hurry. The main principle of

FaderGlow is to indicate the current fader function with colour, so more immediate recognition is possible.

Soundcraft FaderGlow is tted to all console faders that can change their function.

The Si Performer FaderGlow colours are:

YELLOW: MIX 1-14 PRE-FADE bus master or contribution.

GREEN: MIX 1-14 POST FADE bus master or contribution

ORANGE: MATRIX master or matrix contribution.

CYAN: Stereo Input patched as an FX return or contribution.

MAGENTA: Stereo Input patched as a line source other than FX.

WHITE: DMX Control Fader OR linked Mono Input Channel.

RED: GEQ (Graphic Equaliser).

BLUE: VCA Group Master.

User Manual

3.0: ASSIGNABLE CONTROLS

ASSIGNABLE CONTROLS

3.0: ASSIGNABLE CONTROLS

At the heart of the Si Performer is a group of assignable controls that make the console easier and

faster to navigate and operate. Assignable controls work by changing the function of sections of the

console surface. In this way, a single control can do several jobs, depending on the mode the

console is working in. It is important that you understand the assignable controls on the console in

order to use it effectively - especially the way in which the FADERS and FADER FOLLOW buttons

together determine the functionality of the Control Channels and Faders.

The main assignable controls on the console are:

Control Channels

These are the vertical strips containing a Fader, Encoder, Status/Meter screen, plus the SOLO, SEL, and ON

switches. They are assigned to control real input and output channels as well as GEQ bands and DMX channels or Mas-

ters. A group of Control Channels makes a Fader Layer.

Fader Layers (Selected with the FADERS button group)

Switch between whole layers of Control Channels. There are four DSP Control Channel Fader Layers (audio), four DMX

Fader layers, and two GEQ Fader Layers.

Assignable Channel Strip (ACS)

Used to control nearly all parameters on the active channel. Press a Control Channel SEL button to ‘focus’ the ACS.

Global Mode Encoders

Control Channel Encoders (top of Control Channels) change function depending on the Global Encoder Mode.

tOTEM (FADER FOLLOW button group)

The One Touch Easy Mix system used to assign Mix, Matrix, and FX Send busses to the Control Channel Faders.

User Manual

3.1: FADER LAYERS

ASSIGNABLE CONTROLS > FADER LAYERS

3.1: ASSIGNABLE CONTROLS > FADER LAYERS

The are four main Fader Layers on the Expression console, selected by the FADERS button

(A, B, C, and D) group to the right of the Control Channels. The additional buttons in this group

assign Graphic EQ bands across the faders for convenient control.

Each layer is made up of a number of Control Channel assignments. The Performer 1 has 14 Control Channels, the

Performer 2 has 22, and the Performer 3 has 30 - plus the Left/Right and Mono/Centre main mix Control Channels.

By default, Layers A and B are assigned to input channels, with the Stereo input channels on the right hand end of layer

B; Layer C is assigned to Mix Master channels and DMX Masters; and the rst four Control Channels of Layer D are

assigned to the Matrix Master channels.

These assignments are user congurable in the FADER SETUP Touch Screen menu (see the Control Channel

Assignment section 3.2.1).

To select the four DMX layers, press and hold the ALT button and select one of the FADERS buttons (A, B, C, or D).

The selected layer button will turn oraange to indicate a DMX layer is active. Press that button again to return to normal

DSP layers.

User Manual

3.2: CONTROL CHANNELS

ASSIGNABLE CONTROLS > CONTROL CHANNELS

3.2: ASSIGNABLE CONTROLS > CONTROL CHANNELS

A Control Channel is an assignable Channel Strip for DSP channels, with Encoder, Fader, indicators,

plus ON, SOLO, and SEL buttons. The SEL button is used to focus the Assignable Channel Strip

(ACS) on that channel. The DSP channel controlled by a Control Channel is determined by the

current Fader Layer (FADERS button group) and assignment (FADER SETUP Touch Screen menu).

For more information on the individual controls, see section 7.3.

Control Channel assignment is dealt with in 3.2.1.

User Manual

3.2.1: CONTROL CHANNEL ASSIGNMENT

CONTROL CHANNELS > ASSIGNMENT

3.2.1: ASSIGNABLE CONTROLS > CONTROL CHANNELS > ASSIGNMENT

Control Channel Assignment is accessed via the FADER SETUP button in the Touch Screen Main

Menu. Select the Control channel using the Fader Layer and SEL buttons in the usual way - the cur-

rent Fader Bank and Slot Number cannot be edited in the FADER SETUP menu.

A DSP channel, VCA Master, or DMX Master can be assigned to more than one Control channel though,

the Assignment menu parameters are exclusive - you cannot assign more than one function to a Control

Channel.

Fader Bank

Shows the currently selected Fader Layer.

This parameter cannot be edited in the menu - use the FADER button group to switch Fader Layers.

Slot Number

Shows the currently selected Slot Number (Control Channel Number) in current Fader Layer.

This parameter cannot be edited in the menu - use the Control Channel SEL buttons to choose a Slot/Control

Channel Number.

Assign Mono Inputs

Assign a Mono Input channel to the currently selected Control Channel.

Touching the value ﬁeld will bring up a scrollable list of available Mono Input Channel names.

User Manual

3.2.1: CONTROL CHANNEL ASSIGNMENT

CONTROL CHANNELS > ASSIGNMENT

3.2.1: ASSIGNABLE CONTROLS > CONTROL CHANNELS > ASSIGNMENT

Assign VCA

Assign a VCA Master Channel to the currently selected Control Channel.

Touching the value ﬁeld will bring up a scrollable list of available VCA Masters 1 - 8.

Assign Stereo Inputs

Assign a Stereo Input channel to the currently selected Control Channel.

Touching the value ﬁeld will bring up a scrollable list of available Stereo Input Channel names.

Assign DMX

Assign a DMX Master Channel to the currently selected Control Channel.

Touching the value ﬁeld will bring up a scrollable list of available DMX Masters 1 - 4.

Assign Mixes

Assign a MIX Master channel to the currently selected Control Channel.

Touching the value ﬁeld will bring up a scrollable list of available MIX Master Channel names.

RESET LAYER

Reset the currently selected Fader Layer to its default Control Channel Assignments.

You will be asked to conﬁrm this action as it will destroy any custom assignments on the current Fader Layer.

Assign MTX

Assign a Matrix Master Channel to the currently selected Control Channel.

Touching the value ﬁeld will bring up a scrollable list of available Matrix Master Channel names.

User Manual

3.2.1: CONTROL CHANNEL ASSIGNMENT

CONTROL CHANNELS > ASSIGNMENT

3.2.1: ASSIGNABLE CONTROLS > CONTROL CHANNELS > ASSIGNMENT

INSERT BLANK

Insert a blank Control Channel into the currently selected Control Channel Slot and shift the

others to the left or right.

Choosing INSERT BLANK >> (right), for example, will push all Control Channels to the right of the currently

selected slot, one slot to the right. The rightmost control channel will be lost. You will be asked to conﬁrm this

action.

SHIFT

Shift the currently selected channel allocation to the left or the right, as long as there is an

unassigned slot available.

SHIFT>> and/or SHIFT<< will only be available when an adjacent unassigned Control Channel slot is available in

the direction of the Shift.

Page is loading ...

SoundCraft Si Performer Owner's manual

This manual is also suitable for

SoundCraft Si Performer Owner's manual

Related papers

Other documents