American Standard VertiSpa 6035 User manual

American Standard
Brand
American Standard
Model
VertiSpa 6035
Category
Sanitary ware
Type
User manual

This manual is also suitable for

M968416 REV 1.1
Certified to comply with ANSI A112.18.1M
6035
1
REMOVE EXISTING
SHOWER HEAD
2
INSTALL PIPE NIPPLE
Tools required for installation:
Adjustable Wrench
ROUGHING-IN DIMENSIONS
Designer Shower
Massage System
™
Installation
Instructions
Thank you for selecting American-Standard...the benchmark of
fine quality for over 100 years.
25-7/8"
4-3/8"
38-1/8"
3-5/8"
3"
8-5/8"
9-3/4"
UP AND DOWN
ADJUSTMENT
11-3/4 MAX."
6-1/4 MIN."
37-5/16"
MTG. HOLE
REFERENCE
10'
Level
Tape
Measure
5/16"
Drill Bit
Drill
Phillips Screwdriver
Using an adjustable wrench or channel
locks, remove the existing Shower Head,
Arm and Flange (1) by turning
counter-clockwise.
Figure 1.
Apply Teflon tape (provided) to the end of the PIPE NIPPLE (1).
Figure 2.
Thread PIPE NIPPLE (1) into elbow fitting, using adjustable wrench
and tighten. Then, using a hacksaw, cut off excess PIPE NIPPLE (1) at the 3rd
groove from the finished wall. Discard the excess pipe and remove any burrs and
debris from the nipple.
Figure 3
. Install O-RING (2) into groove next to finished wall. One extra
O-RING (2) is provided in parts bag.
1
1
EXCESS PIPE
NIPPLE
MAKE CUT AT 3rd
GROOVE FROM
FINISHED WALL
123
Figure 2
Figure 3
Teflon
Tape
FINISHED WALL
FINISHED
WALL
1/2" NPT
Figure 1
Hacksaw
Hacksaw
65" TO 78"
TO FINISHED FLOOR
(OPTIONAL)
Channel Locks
Channel Locks
Adjustable Wrench
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
2
4
4b
4a
3
INSTALL the
™
UNIT
FOR THIN WALL INSTALLATIONS
FOR TILE, CORIAN
®
OR MARBLE/GRANITE WALL INSTALLATIONS
Note: For granite (Marble) wall Installations use of a hammer drill is suggested.
INSTALL DIVERTER WITH SHOWER HEAD
Adjustable Wrench
SHOWER HEAD
REMOVED
3/16" CARBIDE DRILL
Figure 3
. Use 5/16" standard drill bit (not provided) and drill two mounting
holes as detailed above. (Caution: Take care when drilling between the Diverter
and the Valves as water pipes may be located here.)
Insert two TOGGLE ANCHORS (1) and secure unit using the two screws provided.
Ensure ESCUTCHEON (1) is assembled onto DIVERTER (2).
Hold DIVERTER BODY (2) and thread the DIVERTER (2)
with SHOWER HEAD (3) onto NIPPLE (4) until snug against
the finished wall and in position as shown.
Remove END CAPS (1) from the two ends by sliding forward over the detents as arrows show in illustration. Locate the unit vertically on
the shower wall in the desired position. (Do not mount the unit closer than 6-1/4" (160mm) or further than 11-3/4" (300mm) from
the DIVERTER.
Figure 1
. Hold Vertispa unit in desired location. Refer to roughing-in dimensions.
Mark location of the upper mounting hole. Using a 3/16" carbide drill bit (provided), drill the mounting hole into the shower wall and
install hardware, (See Figure 2). (Caution: Take care when drilling between the Diverter and the valves as water pipes maybe located here).
Mount the unit with screw provided and set the unit vertical using a level. Now mark the lower mounting hole. Remove or swing aside the
unit, drill lower mounting hole and install hardware into mounting hole.
Use mounting screw provided to secure lower section of unit. Slide END CAPS (1) back into position.
(NOTE: If customer desires to use alternate shower head, then pull
back Escutcheon (1) on SHOWER HEAD (2) and turn counter-clockwise
with an adjustable wrench. Replace with customer shower head,
arm and flange.)
1
2
1
1
2
3
1
1
Figure 2
Figure 1
Figure 3
1-1/4" DEEP
DRILL
MOUNTING
HOLE
SQUEEZE ENDS
TOGETHER AND
INSTALL INTO
MOUNTING HOLES.
PUSH RIBBED
ANCHORS IN
MOUNTING
HOLE
MOUNT UNIT
WITH SCREWS
PROVIDED
MOUNT UNIT
WITH SCREWS
PROVIDED
5/16"
4
M968416 REV 1.1
2
5
6
OPERATION
5
CONNECT FLEXIBLE HOSE TO DIVERTER
7
MAINTENANCE
9-3/4"
UP AND DOWN
TRAVEL OF UNIT
Removing spray for cleaning or changing spray location
Figure 1.
Unscrew the TRIM RING (2) on the outside of the SPRAY HEADS (1)
by twisting 1/8th of a turn counter-clockwise.
Remove the O-RING (4) and NOZZLE (3).
Nozzle (3) can be cleaned using soft bristled brush.
Replace O-RING (4) and NOZZLE (3) and lock the TRIM (2) into place by
twisting it clockwise until it clicks.
Adjusting tension of SPRAY UNIT on vertical rails.
Shower system comes with two FRICTION CLIPS (5)
installed.
Move SPRAY UNIT (6) up and down along vertical
rails. FRICTION CLIP (5) holds the SPRAY UNIT (6)
at desired location.
(Figure 2)
If SPRAY UNIT (6) has too much tension on
vertical rails, then remove one FRICTION CLIP (5) or
reposition the CLIPS (5) closer to the center of the
unit. (Note: Tension on vertical rails will reduce when
shower system is moistened from shower application.)
SPRAY UNIT (1) can be adjusted up
and down by sliding unit along the
rails. (See Maintenance section for
steps to adjust the tension of SPRAY
UNIT (1) on the rails.)
Shower function can be diverted by
rotating DIVERTER ARM (2) clockwise
for flow out of SPRAYS (3) and counter-
clockwise for flow out of
SHOWER HEAD (4).
SHOWER HEAD SPRAY (5) can be
adjusted by rotating outer ring on
the faceplate.
(Figure 3)
To replace FRICTION CLIP (5), insert
groove of FRICTION CLIP (5) onto inside edge of
SPRAY UNIT (6). Rotate other end down and press
until the FRICTION CLIP (5) snaps into position onto
tab of SPRAY BODY (7).
2
1
5
5
5
7
2
1
3
4
4 3
COUNTER-CLOCKWISE
TO REMOVE
CLOCKWISE
TO INSTALL
31
Thread the HOSE COUPLING (1) onto DIVERTER
NIPPLE (2) and hand tighten clockwise. Note: Moulded
end of HOSE COUPLING (1) creates watertight seal with
with thread of DIVERTER NIPPLE (2), so seal washer is
not required.
Make sure HOSE (3) is not kinked or twisted.
GROOVE
TAB
VERTICAL RAILS
6
Figure 1
Figure 2
Figure 3
6
8
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT
CLEAN WITH CLEAR WATER. DRY
WITH A SOFT COTTON FLANNEL
CLOTH.
DO NOT: CLEAN THE PRODUCT WITH
SOAPS, ACID, POLISH, ABRASIVES,
HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Product names listed herein are trademarks of American Standard Inc.
©American Standard Inc. 2004
M968416 REV 1.1
MODEL NUMBER
6035
Designer Shower
Massage System
™
M962290-YYY0A
SPRAY TRIM KIT
M923106-0070A
FRICTION CLIP
M962292-0070A
MOUNTING KIT
- SCREWS (2)
- ANCHOR (2)
- TOGGLE ANCHOR (2)
- DRILL BIT (1)
- TEFLON TAPE (1)
M923107-0070A
PIPE NIPPLE
M907526-YYY0A
ESCUTCHEON
M950120-YYY0A
DIVERTER UNIT
M950130-YYY0A
SHOWER HEAD
M912119-0070A
O-RING
M962291-0070A
SPRAY NOZZLES KIT
CHROME 002
Replace the "YYY" with
appropriate finish code
M923112-YYY0A
END CAP
M968416 REV 1.1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

American Standard VertiSpa 6035 User manual

American Standard
Brand
American Standard
Model
VertiSpa 6035
Category
Sanitary ware
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents