Videotec NTM User manual

EN

English - Instruction manual

IT

Italiano - Manuale di istruzioni

FR

Français - Manuel d’instructions

DE

Deutsch - Bedienungsanleitung

RU

Русский - Руководство по эксплуатации

ITALIANO

NTM

Housing for thermal cameras in hostile environments

Page is loading ...

EN

English - Instruction manual

ENGLISH

NTM

Housing for thermal cameras in hostile environments

EN - English - Instruction manual

2 MNVCNTM_2021_EN

Contents

ENGLISH 1

1 About this manual ....................................................................................................................3

1.1 Typographical conventions ................................................................................................................................................ 3

2 Notes on copyright and information on trademarks .............................................................3

3 Safety rules................................................................................................................................3

4 Identication .............................................................................................................................4

4.1 Product description and type designation ................................................................................................................... 4

4.2 Product marking ..................................................................................................................................................................... 4

5 Preparing the product for use .................................................................................................4

5.1 Unpacking ................................................................................................................................................................................. 4

5.2 Contents .................................................................................................................................................................................... 4

5.3 Safely disposing of packaging material ......................................................................................................................... 4

6 Installation ................................................................................................................................4

6.1 Housing opening .................................................................................................................................................................... 4

6.2 How to install the camera .................................................................................................................................................... 5

6.2.1 12Vdc/24Vac version .............................................................................................................................................................................. 5

6.2.2 120/230Vac version .................................................................................................................................................................................5

6.3 Housing closure ...................................................................................................................................................................... 5

6.4 Installing the housing ........................................................................................................................................................... 6

6.4.1 Sunshield mounting (optional) ..........................................................................................................................................................6

6.5 Replacement of the germanium window ..................................................................................................................... 7

7 Cleaning ....................................................................................................................................7

7.1 Cleaning the window ............................................................................................................................................................ 7

8 Information on disposal and recycling ...................................................................................7

9 Technical data ...........................................................................................................................8

9.1 General ....................................................................................................................................................................................... 8

9.2 Mechanical ................................................................................................................................................................................ 8

9.3 Housing's window .................................................................................................................................................................. 8

9.4 Electrical..................................................................................................................................................................................... 8

9.5 Environment ............................................................................................................................................................................. 8

9.6 Certications ............................................................................................................................................................................ 8

10 Technical drawings .................................................................................................................9

Instruction manual - English - EN

3MNVCNTM_2021_EN

1 About this manual

Read all the documentation supplied carefully before

installing and using this unit. Keep the manual in a

convenient place for future reference.

1.1 Typographical conventions

DANGER!

High level hazard.

Risk of electric shock. Disconnect the

power supply before proceeding with any

operation, unless indicated otherwise.

CAUTION!

Medium level hazard.

This operation is very important for the

system to function properly. Please read

the procedure described very carefully and

carry it out as instructed.

INFO

Description of system specications.

We recommend reading this part carefully

in order to understand the subsequent

stages.

2 Notes on copyright and

information on trademarks

The mentioned names of products or companies are

trademarks or registered trademarks.

3 Safety rules

CAUTION! Device installation and

maintaining must be performed by

specialist technical sta only.

CAUTION! The electrical system to which the

unit is connected must be equipped with a

10A max automatic bipolar circuit breaker.

The minimum distance between the circuit

breaker contacts must be 3mm (0.1in).

The circuit breaker must be provided

with protection against the fault current

towards the ground (dierential) and the

overcurrent (magnetothermal).

• The manufacturer declines all responsibility

for any damage caused by an improper use

of the appliances mentioned in this manual.

Furthermore, the manufacturer reserves the right

to modify its contents without any prior notice.

The documentation contained in this manual has

been collected and veried with great care. The

manufacturer, however, cannot take any liability

for its use. The same thing can be said for any

person or company involved in the creation and

production of this manual.

• Before starting any operation, make sure the

power supply is disconnected.

• Be careful not to use cables that seem worn or old.

• Never, under any circumstances, make any

changes or connections that are not shown in

this handbook. Improper use of the appliance

can cause serious hazards, risking the safety of

personnel and of the installation.

• Use only original spare parts. Non-original spare

parts could cause re, electrical discharge or other

hazards.

• Before proceeding with installation, check the

supplied material to make sure it corresponds

to the order specication by examining the

identication labels (4.2 Product marking, page 4).

• Equipment intended for installation in Restricted

Access Location performed by specialist technical

sta.

EN - English - Instruction manual

4 MNVCNTM_2021_EN

4 Identication

4.1 Product description and type

designation

This housing for thermal camera provides the vision

also in complete darkness, fog, rain, smoke or for

long-range distances.

The germanium window has non-scratch treated,

Hard Carbon Coating (DLC) on the outside and

antireection inside; the spectral range is from 7.5μm

to 14μm.

The AISI 316L stainless steel construction allows the

installation in environments with highly corrosive

external agents, such as marine, industrial or

chemical environments.

The NTM housing can be installed on NXPTH Pan &

Tilt head, to obtain a complete positioning system.

4.2 Product marking

See the label attached to the product.

5 Preparing the product for

use

Any change that is not expressly approved

by the manufacturer will invalidate the

guarantee.

5.1 Unpacking

When the product is delivered, make sure that the

package is intact and that there are no signs that it

has been dropped or scratched.

If there are obvious signs of damage, contact the

supplier immediately.

When returning a faulty product we recommend

using the original packaging for shipping.

Keep the packaging in case you need to send the

product for repairs.

5.2 Contents

Check the contents to make sure they correspond

with the list of materials as below:

• Housing

• Housing equipment:

• Allen wrench

• Spacers

• Bolts and screws

• Instruction manual

5.3 Safely disposing of packaging

material

The packaging material can all be recycled. The

installer technician will be responsible for separating

the material for disposal, and in any case for

compliance with the legislation in force where the

device is to be used.

6 Installation

6.1 Housing opening

Unscrew the screws (01) on the rear ange (02) using

the hexagonal wrench (03) provided.

02 0301

Fig. 1

Slide out the rear cover plate of the housing, taking

care to leave the sealing washer in its seating.

Fig. 2

Instruction manual - English - EN

5MNVCNTM_2021_EN

6.2 How to install the camera

Assemble the camera on the slide using the

insulating spacer (01) and the 1/4” screw and the

washer (02) provided. If necessary, use the spacers to

position the camera and lens correctly.

Fig. 3

Insert the cables through the cable glands and

electrically connect.

Ensure the cable glands are rmly fastened.

6.2.1 12Vdc/24Vac version

When the power supply voltage is 24Vac the circuit

will be connected by the terminals shown.

Heater OUT 12Vdc/24VacOUT 12Vdc/24Vac

IN 12Vdc/24Vac

Fig. 4

Nominal section of the cables used: from

0.2mm² (24AWG) up to 2.5mm² (13AWG).

6.2.2 120/230Vac version

When the power supply voltage is 120/230Vac the

circuit will be connected by the terminals shown.

OUT 120/230Vac

IN 120/230Vac

Heater OUT 120/230Vac

Fig. 5

Nominal section of the cables used: from

0.2mm² (24AWG) up to 2.5mm² (13AWG).

6.3 Housing closure

Before closing the housing reinsert the bottom

orientating the slide according to the installation

required, on the wall bracket or on the Pan & tilt

head, for the right camera tting (6.4 Installing the

housing, page6).

Pay attention not to damage the gasket.

Make sure that the sealing ring is correctly tted in

its position.

EN - English - Instruction manual

6 MNVCNTM_2021_EN

6.4 Installing the housing

Before closing the housing, be sure to have rightly

tted the internal slide according to the type of

installation.

Fig. 6 Bracket mounting.

Fig. 7 P&T installation.

6.4.1 Sunshield mounting (optional)

Between the sunshield and the anges of the

housing, position the spacers supplied. Then,

fasten the sunshield to the housing with the screws

supplied, corresponding to the spacers.

Fig. 8

Instruction manual - English - EN

7MNVCNTM_2021_EN

6.5 Replacement of the

germanium window

Germanium glass has two colours. Inside the housing

there is an anti-reection coating that changes

colour (depending on the direction of vision). On the

outside, on the other hand, there is a scratchproof

coating to make the glass dark grey in colour. To

install the new glass refer to the next gure.

Fig. 9

The housing has a ange with a germanium window

with a diameter of 55mm and 2mm thick.

The graph shows the transmittance spectrum for the

window.

0

40

20

60

80

7.5 8.5 9.5 10.5 11.5 12.5 13.5

8 9 10 11 12 13

Ge 2 mm, AR/AR+DLC

Fig. 10

7 Cleaning

7.1 Cleaning the window

Avoid ethyl alcohol, solvents, hydrogenated

hydrocarbide, strong acid and alkali. Such

products may irreparably damage the

surface.

We recommend using a soft cloth with neutral soap

diluted with water or specic products to clean the

glasses lenses.

The device should be cleaned using a damp cloth;

compressed air must not be used.

8 Information on disposal

and recycling

The European Directive 2012/19/EU on Waste

Electrical and Electronic Equipment (WEEE) mandates

that these devices should not be disposed of in the

normal ow of municipal solid waste, but they should

be collected separately in order to optimize the

recovery stream and recycling of the materials that

they contain and to reduce the impact on human

health and the environment due to the presence of

potentially hazardous substances.

The symbol of the crossed out bin is marked

on all products to remember this.

The waste may be delivered to appropriate collection

centers, or may be delivered free of charge to the

distributor where you purchased the equipment at

the time of purchase of a new equivalent or without

obligation to a new purchase for equipment with size

smaller than 25cm (9.8in).

For more information on proper disposal of these

devices, you can contact the responsible public

service.

EN - English - Instruction manual

8 MNVCNTM_2021_EN

9 Technical data

9.1 General

Housing manufactured in polished stainless steel

(austenitic stainless alloy steel resistant to corrosion

and heat):

• AISI 316L

• UNI 6900-71: X 2 Cr Ni Mo 17 12 2

• DIN 17006: X 2 Cr Ni Mo 17 13 2

• N° werksto: 1.4404

• AFNOR: Z2 CND 17-12

• BSI: 316S11

The screws utilised are in austenitic alloy stainless

steel, corrosion and heat resistant according to the

following standards:

• ISO: 7380

• AISI: 316

• ISO quality: A4

9.2 Mechanical

Internal usable area (WxH): 88x86mm (3.5x3.4in)

Internal usable length (without accessories): 334mm

(13.1in)

Internal usable length (with heater and/or power

supply): 245mm (9.6in)

Cable glands: 2xPG13.5 (nickel-plated brass for

external connections)

Flange thickness: 9mm (0.35in) (front/back)

Gaskets: High sealing O-ring

Unit weight: 6kg (13.3lb)

9.3 Housing's window

Germanium window:

• Usable diameter: 55mm (2.1in)

• Thick: 2mm (0.08in)

• External treatment: antiscratch (Hard Carbon

Coating- DLC), antireection

• Internal treatment: antireection

• Spectral range: from 7.5μm up to 14μm

• Medium transmittance (from 7.5μm up to

11.5μm): 90%

• Medium transmittance (from 11.5μm up to 14μm):

77%

9.4 Electrical

Supply voltage/Current consumption (version with

heater, Ton 15°C±3°C (59°F ±5°F), To 22°C±3°C

(72°F±5°F)):

• 12Vdc, 1.6A max

• 24Vac, 0.85A max, 50/60Hz

• 120Vac, 0.35A max, 50/60Hz

• 230Vac, 0.18A max, 50/60Hz

Camera power supply

• IN from 100Vac up to 240Vac, 50/60Hz - OUT

12Vdc, 1.25A

• IN 230Vac, 50Hz - OUT 24Vac, 50Hz, 400mA

9.5 Environment

For indoors and outdoors installation

Operating temperature with heating: from -20°C

(-4°F) up to +60°C (140°F)

9.6 Certications

Electrical safety (CE): EN60065

Electromagnetic compatibility (CE): EN50130-4,

EN61000-6-3

IP protection degree: EN60529 (IP66/IP67)

EAC certication

Instruction manual - English - EN

9MNVCNTM_2021_EN

10 Technical drawings

The indicated measurements are expressed in millimetres.

182

164

Ø 154

460

245

88

86

334

352

100

370

130

115

60

80

M5

A - A

A

B - B

B

POWER SUPPLY

BOARD

USABLE

AREA

USABLE AREA

FIXING BASE

9.3

Ø 55

Ø 72

Ø 154

C

C - C

C

72

FRONT FLANGE

Fig. 11 NTM.

MNVCNTM_2021_EN

Headquarters Italy Videotec S.p.A.

Via Friuli, 6 - I-36015 Schio (VI) - Italy

Tel. +39 0445 697411 - Fax +39 0445 697414

Email: [email protected]

France Videotec France SARL

Immeuble Le Montreal, 19bis Avenue du Québec, ZA de Courtaboeuf

91140 Villebon sur Yvette - France

Tel. +33 1 60491816 - Fax +33 1 69284736

Email: info.fr@videotec.com

Asia Pacic Videotec (HK) Ltd

Flat 8, 19/F. On Dak Industrial Building, No. 2-6 Wah Sing Street

Kwai Chung, New Territories - Hong Kong

Tel. +852 2333 0601 - Fax +852 2311 0026

Email: info.hk@videotec.com

Americas Videotec Security, Inc.

Gateway Industrial Park, 35 Gateway Drive, Suite 100

Plattsburgh, NY 12901 - U.S.A.

Tel. +1 518 825 0020 - Fax +1 518 825 0022

Email: info.usa@videotec.com

www.videotec.com

Page is loading ...

MNVCNTM_2021_IT

Headquarters Italy Videotec S.p.A.

Via Friuli, 6 - I-36015 Schio (VI) - Italy

Tel. +39 0445 697411 - Fax +39 0445 697414

Email: [email protected]

France Videotec France SARL

Immeuble Le Montreal, 19bis Avenue du Québec, ZA de Courtaboeuf

91140 Villebon sur Yvette - France

Tel. +33 1 60491816 - Fax +33 1 69284736

Email: info.fr@videotec.com

Asia Pacic Videotec (HK) Ltd

Flat 8, 19/F. On Dak Industrial Building, No. 2-6 Wah Sing Street

Kwai Chung, New Territories - Hong Kong

Tel. +852 2333 0601 - Fax +852 2311 0026

Email: info.hk@videotec.com

Americas Videotec Security, Inc.

Gateway Industrial Park, 35 Gateway Drive, Suite 100

Plattsburgh, NY 12901 - U.S.A.

Tel. +1 518 825 0020 - Fax +1 518 825 0022

Email: info.usa@videotec.com

www.videotec.com

Page is loading ...

Manuel d’instructions - Français - FR

9MNVCNTM_2021_FR

10 Dessins techniques

Les tailles indiquées sont en millimètres.

182

164

Ø 154

460

245

88

86

334

352

100

370

130

115

60

80

M5

A - A

A

B - B

B

ALIMENTATION

CARTE

SURFACE

UTILE

SURFACE UTILE

BASE DE FIXATION

9.3

Ø 55

Ø 72

Ø 154

C

C - C

C

72

FLASQUE FRONTALE

Fig. 11 NTM.

MNVCNTM_2021_FR

Headquarters Italy Videotec S.p.A.

Via Friuli, 6 - I-36015 Schio (VI) - Italy

Tel. +39 0445 697411 - Fax +39 0445 697414

Email: [email protected]

France Videotec France SARL

Immeuble Le Montreal, 19bis Avenue du Québec, ZA de Courtaboeuf

91140 Villebon sur Yvette - France

Tel. +33 1 60491816 - Fax +33 1 69284736

Email: info.fr@videotec.com

Asia Pacic Videotec (HK) Ltd

Flat 8, 19/F. On Dak Industrial Building, No. 2-6 Wah Sing Street

Kwai Chung, New Territories - Hong Kong

Tel. +852 2333 0601 - Fax +852 2311 0026

Email: info.hk@videotec.com

Americas Videotec Security, Inc.

Gateway Industrial Park, 35 Gateway Drive, Suite 100

Plattsburgh, NY 12901 - U.S.A.

Tel. +1 518 825 0020 - Fax +1 518 825 0022

Email: info.usa@videotec.com

www.videotec.com

Page is loading ...

MNVCNTM_2021_DE

Headquarters Italy Videotec S.p.A.

Via Friuli, 6 - I-36015 Schio (VI) - Italy

Tel. +39 0445 697411 - Fax +39 0445 697414

Email: [email protected]

France Videotec France SARL

Immeuble Le Montreal, 19bis Avenue du Québec, ZA de Courtaboeuf

91140 Villebon sur Yvette - France

Tel. +33 1 60491816 - Fax +33 1 69284736

Email: info.fr@videotec.com

Asia Pacic Videotec (HK) Ltd

Flat 8, 19/F. On Dak Industrial Building, No. 2-6 Wah Sing Street

Kwai Chung, New Territories - Hong Kong

Tel. +852 2333 0601 - Fax +852 2311 0026

Email: info.hk@videotec.com

Americas Videotec Security, Inc.

Gateway Industrial Park, 35 Gateway Drive, Suite 100

Plattsburgh, NY 12901 - U.S.A.

Tel. +1 518 825 0020 - Fax +1 518 825 0022

Email: info.usa@videotec.com

www.videotec.com

Page is loading ...

MNVCNTM_2021_RU

Headquarters Italy Videotec S.p.A.

Via Friuli, 6 - I-36015 Schio (VI) - Italy

Tel. +39 0445 697411 - Fax +39 0445 697414

Email: [email protected]

France Videotec France SARL

Immeuble Le Montreal, 19bis Avenue du Québec, ZA de Courtaboeuf

91140 Villebon sur Yvette - France

Tel. +33 1 60491816 - Fax +33 1 69284736

Email: info.fr@videotec.com

Asia Pacic Videotec (HK) Ltd

Flat 8, 19/F. On Dak Industrial Building, No. 2-6 Wah Sing Street

Kwai Chung, New Territories - Hong Kong

Tel. +852 2333 0601 - Fax +852 2311 0026

Email: info.hk@videotec.com

Americas Videotec Security, Inc.

Gateway Industrial Park, 35 Gateway Drive, Suite 100

Plattsburgh, NY 12901 - U.S.A.

Tel. +1 518 825 0020 - Fax +1 518 825 0022

Email: info.usa@videotec.com

www.videotec.com

Page is loading ...

MNVCNTM_2021

Headquarters Italy Videotec S.p.A.

Via Friuli, 6 - I-36015 Schio (VI) - Italy

Tel. +39 0445 697411 - Fax +39 0445 697414

Email: [email protected]

France Videotec France SARL

Immeuble Le Montreal, 19bis Avenue du Québec, ZA de Courtaboeuf

91140 Villebon sur Yvette - France

Tel. +33 1 60491816 - Fax +33 1 69284736

Email: info.fr@videotec.com

Asia Pacic Videotec (HK) Ltd

Flat 8, 19/F. On Dak Industrial Building, No. 2-6 Wah Sing Street

Kwai Chung, New Territories - Hong Kong

Tel. +852 2333 0601 - Fax +852 2311 0026

Email: info.hk@videotec.com

Americas Videotec Security, Inc.

Gateway Industrial Park, 35 Gateway Drive, Suite 100

Plattsburgh, NY 12901 - U.S.A.

Tel. +1 518 825 0020 - Fax +1 518 825 0022

Email: info.usa@videotec.com

MNVCNTM_2021

www.videotec.com

Videotec NTM User manual

Videotec NTM User manual

in other languages

Related papers

Other documents