TecnoVideo SSH254IR110-L User manual

Category
Security camera accessories
Type
User manual

This manual is also suitable for

SSH254 Series
Extra-Large size Stainless Steel Camera Housing
DESCRIPTION:
The SSH254 series is designed to protect CCTV cameras in outdoor locations, especially where corrosive environment
can cause the premature deterioration of a standard aluminium/plastic camera housing, for this purpose the SSH254
series is constructed entirely from AISI316 stainless steel.
MODELS:
SSH254 254 mm diameter x 600 mm length. Usable front window diameter 200 mm.
SSH254-L 254 mm diameter x 700 mm length. Usable front window diameter 200 mm.
SSH254SH Same as SSH254, plus with sunshield and thermostatically controlled heater.
SSH254SH-L Same as SSH254-L, plus with sunshield and thermostatically controlled heater.
SSH254WW Same as SSH254SH, plus with wiper system. Usable front window diameter 200 mm.
SSH254WW-L Same as SSH254SH-L, plus with wiper system. Usable front window diameter 200 mm.
SSH254IR70 254 mm diameter x 600 mm length with Germanium window 80x3mm (usable diam.
70mm), AR/DLC coating. Sunshield included. Heater optional.
SSH254IR70-L Same as SSH254IR70 but 700 mm tube length.
SSH254IR110 254 mm diameter x 600 mm length with Germanium window 120x3mm (usable
diam.110mm), AR/DLC coating. Sunshield included. Heater optional.
SSH254IR110-L Same as SSH254IR110 but 700 mm tube length.
SSH254IR155 254 mm diameter x 600 mm length with Germanium window 165x5mm (usable diam.
155mm), AR/DLC coating. Sunshield included. Heater optional.
SSH254IR155-L Same as SSH254IR155 but 700 mm tube length.
SSH254WWIR70 Same as SSH254IR70, plus wiper system.
SSH254WWIR70-L Same as SSH254IR70-L, plus wiper system.
SSH254WWIR110 Same as SSH254IR110, plus wiper system.
SSH254WWIR110-L Same as SSH254IR110-L, plus wiper system.
SSH254WWIR155 Same as SSH254IR155, plus wiper system.
SSH254WWIR155-L Same as SSH254IR155-L, plus wiper system.
Issue 2 12/02/2009
Note: all models are available in 500 mm length, we are also ready to fulfil any particular request such as different
housing length or different glass diameter.
Tecnovideo Snc
Via San L. Murialdo, 8
36030 Villaverla (VI) ITALY
Tel. +39-0445-350444
Fax. +39-0445-357259
Web: www.tecnovideocctv.com
INSTALLATION
INSTALLING THE CAMERA
1) Extract the rear flange by removing the eight
screws. Be careful not to lose screws and
washer.
2) Prepare the housing to install the camera,
sliding the upper rail away from the lower rail.
3) Install the camera on the upper rail using one of
the ¼'' screws supplied, the plastic washer and
one or more spacers to be put under the
camera to adjust its height position.
Then slide the upper rail back on the lower rail
into the housing. Perform the electrical and
video connections. Cable glands are situated at
the bottom of the housing near the rear flange.
Eventually close the rear flange.
4) Use the four screws at the bottom of the
housing to fasten the housing to its apposite
support.
Issue 2 12/02/2009
Before performing any operation, turn off the power.
Only qualified personel can perform electrical operations
according to the regulations in force
Prior to installation and operation, read carefully this
manual of instructions
Upper
rail
Lower
rail
washe
r
screws
Cable glands
Screws
5) Only on housing with heater system.
Perform the input and output (to the camera)
voltage connections using the PCB installed
inside the housing near the rear flange.
6) Only on housing with wiper system
Perform wiper electrical connections through the
three coloured wires connected to the wiper
mechanism mounted on the rear flange.
Model with wiper voltage 110-240 VAC
Permanent 110-240VAC voltage must be connected be-
tween the RED wire (line) and the WHITE wire (neutral).
To activate the wiper, connect the Green wire to the
RED wire. An external switch (normally open), con-
nected between Green and RED, can be used for this
operation.
When the voltage is connected to the Green wire, the
wiper works and continues to work until the voltage is
disconnected, then it goes back to its initial position.
Model with wiper voltage 24 VDC (default model)
Permanent 24VDC voltage must be connected between
the GREEN wire (+24V) and the GREY wire (GND). To
activate the wiper, connect the BLUE wire to the GREY
wire (GND). An external switch (normally open), con-
nected between GREY and BLUE, can be used for this
operation.
When the BLUE wire is connected to GND (GREY), the
wiper works and continues to work until the wire is dis-
connected, then it goes back to its initial position.
Issue 2 12/02/2009
Wi
p
er wires
SPECIFICATIONS
OVERALL DIMENSIONS (Dimensions in bracket refer to models SSH254 with 600 mm tube length)
Measure available for “A” (Usable window diameter)
1) = 200 mm for SSH254, SSH254-L, SSH254SH, SSH254SH-L.
2) = 155 mm for SSH254IR155, SSH254IR155-L, SSH254WWIR155 and SSH254WWIR155-L (germanium Win-
dow).
3) = 110 mm for SSH254IR110, SSH254IR110-L, SSH254WWIR110 and SSH254WWIR110-L (germanium Window).
4) = 70 mm for SSH254IR70, SSH254IR70-L, SSH254IR70WW and SSH254IR70WW-L (germanium Window).
INTERNAL DIMENSIONS
Issue 2 12/02/2009
Internal wiper shaft
Internal rail
Wi
p
er mechanism
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

TecnoVideo SSH254IR110-L User manual

Category
Security camera accessories
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI