Jacobsen 62806 Instruction Sheet

Brand: Jacobsen

Model: 62806

Category: Lawnmowers

Type: Instruction Sheet

Instruction

Sheet

When Performance Matters.

™

WARNING

If incorrectly used, this machine can cause severe injury. Those who use

and maintain this machine should be trained in its proper use, warned of its

dangers and should read the entire manual before attempting to set up,

operate, adjust, or service the machine.

1 - INCLUDES ITEMS 3 - 16

22 Inch Reels

11 Blade L.H.

67135 - G-Plex, E-Plex

62808 - Eclipse 322

63308 - Eclipse 122F

9 Blade L.H.

67136 - G-Plex, E-Plex

62807 - Eclipse 322

7 Blade L.H.

67137 - G-Plex, E-Plex

62806 - Eclipse 322

18 Inch Reels

11 Blade L.H.

63309 - Eclipse 118F

3010500-Rev E

This kit is intended for use with the Eclipse 322™, G-Plex™,

E-Plex® Triplex Greens Mowers and Eclipse™ floating reel

walk behind units.

1. Park the unit on a flat and level surface, engage the

parking brake, turn the ignition switch to the OFF posi-

tion and remove the key.

a. Wait for all movement to stop before making any

adjustments or modifications.

b. Allow sufficient time for the unit to cool down.

c. Take this opportunity to thoroughly inspect the

equipment and perform other required maintenance.

Front Roller and Accessories ____________________________________________

The front roller is not included with the reel assembly and

must be ordered separately. Check with your dealer for front

rollers that are available for your unit. Follow installation

instructions included with the front roller.

Other accessories may also be available for your reel such

as Turf Groomer®, roller scrapers, and roller brushes. Install

these accessories before installing reels.

Follow instructions included in your mower’s manuals and/or

Turf Groomer’s Instruction Sheet for adjusting the reel to

bedknife and height of cut.

Mounting the Cutting units on G-Plex and E-Plex Mowers ____________________

1. Before mounting the cutting units make sure the latches

on the pull frames are in the opened position.

2. Position the cutting head at the front of the pull frame.

Align the screw and bushing on each side of the cutting

head below and slightly to the front of the slots on the

pull frame. Push down on the pull frame and roll the

cutting head back slightly until the bushing (on the

cutting head) is positioned in the slot.

3. Pull the latch handle and pivot it to the rear (allow the

bolt head to drop into the center hole) the latch will pivot

forward and lock the bushing into place. [See Figure 3L]

Repeat procedure on opposite side of the cutting head.

Install the remaining cutting units using the same

procedures.

4. Follow directions given with motor adapter kits for

assembling motor to reels.

5. E-Plex Units - Connect the motor harness into the main

harness at the top of the pull frame.

Figure 1 - Quick Detach Latch

Figure 2 - Cutting Head Mounted To Pull Frame

CAUTION

Before you install this kit, read the mower’s Safety &

Operation Manual to become familiar with the

mower, the controls and proper use of the equipment.

Stay alert for potential hazards and follow all safety

precautions. Read all instructions completely and

make sure you understand them before proceeding

with the assembly.

WARNING

Before you attempt to clean, adjust, or repair any of

this equipment, disengage all drives, shut down the

engine and allow the unit to cool. Remove the key

from the ignition switch and disconnect the power

connector to prevent accidental discharge and

potential bodily injuries.

1. PULL HANDLE UNTIL THE HEAD

OF BOLT CLEARS THE HOLE

SHOWN AS

REFERENCE ONLY

2. PIVOT

FORWARD

LATCH IN THE

OPEN POSITION

LATCH LOCKED

TO BUSHING

SHOWN AS

REFERENCE ONLY

Litho in U.S.A. 11-2009

Eclipse 118F and 122F__________________________________________________

1. Remove existing reel from Eclipse mower.

a. Remove the two shoulder bolts (A) and pivot the lift

hangers (B) up and away from the reel.

b. Remove motor mounting hardware (C) and slide reel

motor (D) off end of reel shaft. Remove coupler (E)

from reel shaft.

c. Remove hairpin and flat washer (F) and lift panhard

rod (G) off of reel bolt.

d. Tip the unit back onto the handle and slide the reel

away from the mower.

2. Remove hardware (H) and Panhard rod bracket (J) from

existing reel and assemble to new reel assembly.

3. Tip unit back onto the handle and slide the new reel into

position under mover.

4. Assemble Panhard rod (G), flat washer and hairpin (F)

to reel.

5. Assemble coupler (E) to reel. Check to be certain key

(K) is in position and slide motor (D) onto reel. Secure

with hardware (C).

6. Pivot lift hangers (B) down and secure to reel assembly

using shoulder bolts.

Figure 3

Eclipse 322 ___________________________________________________________

1. If any existing reels are installed, remove them from the

mower.

2. Assemble coupler (A), and O-ring (B) to reel. Check to

be certain key (E) is in position and slide motor (D) onto

reel. Secure with hardware (C).

3. Position reels under lift arms.

4. Start the unit, and fully lower the lift arms. Shut mower

off and remove the key.

5. Assemble reels to lift arms using shoulder bolts (F).

6. Connect reel motor to mower harness. Hand tighten

motor connections only, do not use wrenches to

tighten motor connection. If connector does not

assembly easily, check to be sure that connector is

properly aligned to motor, and there is no debris in

either side of connector.

Figure 4

NOTICE

Gas Engine Power Modules:

Do not leave the

mower tipped back for an extended length of time or

oil may migrate into the combustion chamber

To prevent cuts use

socket wrench or Turf

Groomer knob to

turn reel.

WARNING

To prevent injury, disengage

all drives, engage parking

brake and stop engine before

working in machine or

emptying grass catchers.

DANGER

Optional MagKnife Bedknives

Part Number Description

4131369 22” High Profile

4131004 18” Super Tournament

4131373 18” Tournament

4131371 18” Low Profile

4131001 22” Low Profile

4131370 22” Tournament

4131003 22” Super Tournament

22 Inch Standard Style Bedknives

(Secured with screws)

Part Number Description

◆ 5003150 Medium Section

503477 High Profile

▲ 503478 Low Profile

★ 503479 Tournament

● 5002887 Super Tournament

◆ 62806 and 67137 - Standard Bedknife

▲ 62807 and 67136 - Standard Bedknife

★ 62808 and 67135 - Standard Bedknife

● 63308 - Standard Bedknife

18 Inch

Standard Style Bedknives

(Secured with screws)

Part Number Description

5000098 Low Profile

■ 5002887 High Profile

■ 63309 - Standard Bedknife

22 INCH REEL

Reel Assembly

Serial No. All

> Change from previous revision

22 INCH REEL

Item Part No. Qty. Description Serial Numbers/Notes

5002577 1 Frame, 22 Inch Reel

1 4170204 1 Frame, 18 Inch Reel

2 361877 2 • Decal, Danger Not used on Eclipse Reels

3 1000997 1 • Decal, Warning Not Used on Eclipse Reels

4 5003053 1 22 inch 7 Blade Left Hand Reel Used on 62806 and 67137

4 5001099 1 22 inch 9 Blade Left Hand Reel Used on 62807 and 67136

4 5001101 1 22 inch 11 Blade Left Hand Reel Used on 62808, 63308, and 67135

4 4170220 1 18 Inch 11 Blade Left Hand Reel Used on 63309

5 1004756 1 Bearing Housing

6 500534 1 • Bearing, Cup and Cone

7 336962 1 • Seal, Grease

8 471214 1 • Grease Fitting

9 471242 1 • Vent Fitting

10 445795 2 Nut, 5/16-18 Spiralock Flange Used on 62806~62808, 67135~67137

11 3010293 1 Stop, Mower Used on 62806~62808, 67135~67137

12 458013 1 Snap Ring

13 367164 1 Spacer

14 5000415 1 22 Inch Bedknife Backing

14 2811055 1 18 Inch Bedknife Backing

15 See Chart 1 Bedknife

16 3009138 13 Screw, 1/4-20 x 1/2 in. Flat Head

17 315298 2 Bolt, 7/16 x 3/4 in.

18 337370 1 Coupling Used on 67135 ~ 67137 Only

19 445795 8 Nut, 5/16-18 Hex

20 453009 4 Flat Washer, 5/16

21 1000480 1 Bearing Housing

22 500534 1 • Bearing, Cup and Cone

23 336962 1 • Seal, Grease

24 471214 1 • Grease Fitting

25 471240 1 • Vent Fitting

26 5002151 1 Spring, Compression

27 364900 1 Nut, Reel

28 453011 1 Flat Washer, 3/8

29 163892 1 Seal

30 400192 8 Screw, 5/16-18 x 1-1/2 in. Hex Head

31 446142 4 Lockwasher, 3/8 Heavy

32 304745 1 Washer

33 365246 2 Bolt, Shoulder

34 400294 1 Screw, 3/8-24 x 1 in. Hex Head

35 412503 4 Screw, 3/8-16 x 1-1/4 in. Square Hd

36 400184 2 Screw, 5/16-18 x 3/4 in. Hex Head Used on 62806~62808, 67135~67137

G-Plex

E-Plex

Reel

Eclipse

Reel

4127335

22 INCH REEL

Outer Reel Assembly

Serial No. All

> Change from previous revision

22 INCH REEL

Item Part No. Qty. Description Serial Numbers/Notes

1000770 1 22 Inch Rear Roller Used on 67137 Only

1 1004990 1 22 Inch Rear Roller All 22 Inch Reels, Except 67137

1 4108920 1 18 Inch Rear Roller Used on 63309 Only

2 1002224 2 Zerk Bolt

3 3005692 2 Knob, Front Roller Adjusting

4 441674 2 Carriage Bolt, 5/16-18 x 1-3/4 in.

5 445795 2 Nut, 5/16-18 Spiralock Flange

6 403782 2 Screw, 1/4-20 x 3/4 in. Truss Head

7 2000065 1 Casting, Counterweight Used on 67135 ~ 67137

7 4171380 1 Casting, Counterweight Used on Eclipse Reels

8 446130 4 Lockwasher, 1/4 Heavy

9 400110 2 Screw, 1/4-20 x 7/8 in. Hex Head Used on 67135 ~ 67137

9 400118 2 Screw, 1/4-20 x 1-3/4 in. Hex Head Used on Eclipse Reels

10 4174640 1 Shield, 22 Inch Reel

10 2811027 1 Shield, 18 Inch Reel

11 4127335 2 • Decal, Danger Used on Eclipse Reels Only

12 443102 4 Nut, 1/4-20 Hex

13 453023 2 Flat Washer, 1/4

14 343616 2 Stud

15 352737 2 Screw, 1/4-20 x 7/8 in. Sq Hd Set

16 3008438 1 Roller Bracket

17 3008439 1 Roller Bracket

18 4167400 1 Adapter, Motor Used on Eclipse Reels Only

19 845279 1 Seal, O-Ring Used on Eclipse Reels Only

20 434024 4 Screw, 5/16-18 x 3/4 in. Socket Head Used on Eclipse Reels Only

> Change from previous revision

22 INCH REEL

Rear Roller

Part Number 1000770

Item Part No. Qty. Description Serial Numbers/Notes

3001654 1 Shaft, Roller

2 3001655 1 Tube, Roller

3 3001656 2 Seal, Grease

4 5000625 2 Bearing, Cup and Cone

5 3000983 2 Seal, Grease

6 3001762 2 Sleeve, Wear

7 445801 2 Locknut, 5/16-18 HEC HD

8 3000698 2 Washer

> Change from previous revision

22 INCH REEL

Rear Roller

Part Number 1004990 and 4108920

Item Part No. Qty. Description Serial Numbers/Notes

N/S 1 Tube, Roller

2 3010422 1 22 Inch Roller Shaft

2 4108924 1 18 Inch Roller Shaft

3 3010286 2 Seal

4 3010712 2 Bearing

> Change from previous revision

MOTOR ADAPTER KIT

Greensplex Greensmower Reel Motor Adapter Kit

Part No. 894991

Item Part No. Qty. Description Serial Numbers/Notes

894991 1 Greensplex Reel Motor Adapter Kit

1 103867 2 • Flat Washer, 516

2 306325 2 • Lockwasher, 5/16

3 306501 2 • Screw, 5/16-18 x 1-1/2”

4 337370 1 • Coupling, Drive

5 845278 1 • Adapter Plate

6 845279 1 • Seal, O-Ring 1.49 I.D. x .07

7 845280 1 • Seal, O-Ring 1.99 I.D. x .07

Note: This cutting head requires the Motor Adapter Kit 894991.

Check to make sure your Greensplex Greensmower has this Motor

Adapter Kit before installing the cutting head.

If your Greensplex Greensmower does not have this Motor Adapter, you

need to order a Motor Adapter kit Part No. 894991.

> Change from previous revision

MOTOR ADAPTER KIT

E-Plex Electric Greensmower Motor Adapter Kit

Part Number 894996

Item Part No. Qty. Description Serial Numbers/Notes

894996 1 E-Plex Motor Adapter Kit

>12703647 1 • Adapter, Motor

2 845279 1 • Seal, O-Ring 1.49 I.D. x .07”

3 894987 1 • Guard, Motor

4 895001 1 • Coupling, Drive

Note: This cutting head requires the Motor Adapter Kit 894996.

Check to make sure your E-Plex Electric Greensmower has this Motor

Adapter Kit before installing the cutting head.

If your E-Plex Electric Greensmower does not have this Motor Adapter,

you need to order a Motor Adapter kit Part No. 894996.

Jacobsen, A Textron Company

11108 Quality Drive, Charlotte, NC 28273

www.Jacobsen.com

800-848-1636

When Performance Matters.

™

Equipment from Jacobsen is built to exacting

standards ensured by ISO 9001 and ISO 14001

registration at all of our manufacturing locations.

A worldwide dealer network and factory trained

technicians backed by Genuine Jacobsen Parts

provide reliable, high-quality product support.

Jacobsen 62806 Instruction Sheet

Brand: Jacobsen

Model: 62806

Category: Lawnmowers

Type: Instruction Sheet

Download PDF

report

Jacobsen 62806 Instruction Sheet

Jacobsen 62806 Instruction Sheet

Related papers

Other documents