JUNG TKVU4 Operating instructions

JUNG
Brand
JUNG
Model
TKVU4
Category
Door intercom systems
Type
Operating instructions
1
Product Information
DCM Video switch 4-gang
TK VU 4 REG
Safety instructions
!
Assembly, installation, and commissioning must only be carried out by a qualified
electrician
For work on systems with 230 V AC mains current the safety requirements of DIN VDE
0100 must be observed.
When installing DCM BUS systems the general safety rules for telecommunication sys-
tems in accordance with VDE 0800 must be observed:
• separate cabling for high and low voltage lines
• minimum distance of 10 cm for joint cabling arrangements,
• use of separators between high and low voltage lines in joint cable ducts,
• use of standard telecommunication cables, e. g. J-Y (St) Y with 0.8 mm² cross section
!
Suitable lightning prediction must ensure that a voltage of 32 V DC will not be
exceeded at the DCM BUS wires a and b.
DCM = Door Communication Management
2
Device overview
Technical data
Input voltage: + 24 V ± 8 % (Power supply &control unit)
Housing: rail mounting device, 6 rail units
Weight: 200 g
Permissible ambient temperature: 0 °C to 40 °C
Input current: I(a) = 0.4 mA, I(P) = 21 mA
Run/Pro
g
-button
Run/Prog-indication
Ste
p
terminal
Hold terminal
Output terminal
Terminals for camera input 1-3
Terminals for camera input 4
3
Application
The TK VU 4 REG is designed to switch between four video signals, which will be received
of one (or more) video indoor stations.
Up to 4 video switches can be installed in a DCM system. In this case the output terminals
(3-7) will be wired parallel. Please install the all video switches side by side in the distribu-
tion board to achieve the best camera image quality.
!
In an installation with multiple video switches, you have to finish all required program-
ming steps before you trigger a bell button or start a communication. Otherwise multiple
video signals will be switched on at the same time.
Brief description
Functions
Automatic switching to the triggered outdoor station
Video inputs 4
Video outputs 1
4
Cable connection
Wiring diagram
Wiring example
Video outdoor station 1:
AS-address = 01
program and lock
Video outdoor station 2:
AS-address = 02
program and lock
Audio outdoor station 3:
AS-address = 03
program and lock
Video input 4 not connected
Program input as "unused" !
V
ideo outdoor
station 1
V
ideo outdoor
station 2
5
Commissioning
• Install all of the devices of the system completely.
• Check the a, b and P wires for short-circuit.
• Switch on the mains voltage.
!
Please complete the full installation before you connect the system to
the mains voltage!
• Do NOT connect V1 and V2 with the P-, M-, a- or b-wire. Even a connection for a
quick moment will destroy the device.
• When connecting the video wires V1 (+) and V2 (-) observe polarity.
If you can see a distorted image on the display, switch off the mains voltage and
change the wires V1 and V2..
Settings
Factory setting
The inputs S1, S2, S3, S4 are pre-programmed with the AS-addresses 1, 2, 3 and 4.
Device settings
You can program the video switch with the service device TK-SERVICE or the
commissioning software TK-IBS-TOOL.
Each outdoor station has to be assigned with an AS-address. The AS-address has to be
locked. Thus every door call transmitted the respective AS address of the outdoor station.
The video switch allocates the video inputs to the respective AS addresses. A video input
will be automatically activated with a triggered door call. The AS-address of the video input
has to comply with the AS-address of the outdoor station.
The combination with audio outdoor station is possible.
!
Caution!
Link outdoor stations without camera with AS-addresses greater 31
and lock the programmed AS-addresses.
!
Caution!
Video outdoor stations or cameras without outdoor stations have to be linked
with available AS addresses from 0 to 30.
Please only use the function: "Connect camera input with video outdoor station".
6
Example
Connection of 2 video outdoor stations to the camera inputs S1 and S2.
• Assign the AS-addresses of the outdoor stations to AS=1 and AS=2 and lock
the AS-addresses ( with service device or commissioning software, see manual of out-
door station )
• Connect the outdoor station (AS=1) to the input S1.
• Connect the outdoor station (AS=2) to the input S2.
• Assign the unused inputs with " Input unused"
Programming
Programming with the service device TK SERVICE
• Assign and lock all AS addresses of the out door stations
• Assign the bell buttons of the out door stations with the serial no. of the respective
indoor station
• Assign the camera inputs S1, S2, S3 and S4 of the TK VU4 REG to the respective
AS-addresses with the function "Connect camera input with video outdoor station", if
factory settings have to changed.
• Assign unused camera input
NOTE: First assign and lock the AS-addresses of the video outdoor station.
Connect camera input with video outdoor station
Assign unused camera input
NOTE: Camera input 1 cannot be assigned as "unused".
TK VU 4 REG - Load factory settings
Ser.-Nr.M = Seriial number ofr TK VU4 REG
K = Number of the camera input of TK VU4 REG (= 1 ... 4)
AS = AS-address of outdoor stations for this camera input (= 0 ... 63)
Programming with the commissioning software TK-IBS-TOOL
• Assign and lock all AS addresses of the out door stations
• Assign the bell buttons of the out door stations with the serial no. of the respective
indoor station
• Assign the camera inputs S1, S2, S3 and S4 of the TK VU4 REG to the respective
AS-addresses.
• Select for unused camera inputs: Input unused
7
Acceptance of guarantee
We accept the guarantee in accordance with the corresponding legal provisions.
Please return the unit postage paid to our central service department giving
a brief description of the fault:
ALBRECHT JUNG GMBH & CO. KG
Service-Centre
Kupferstr. 17-19
44532 Lünen
Germany
Service-Line: 0 23 55 . 80 65 51
Telefax: 0 23 55 . 80 61 89
E-Mail: [email protected]
Technique (DCM)
Service-Line: 0 23 55 . 80 65 52
Fax: 0 23 55 . 80 62 55
E-Mail: [email protected]
Albrecht Jung GmbH & Co. KG
P.O. Box 1320
58569 Schalksmühle
Germany
http://gb.jung.de/
www.jung-catalogue.com
The
-sign is a free trade sign addressed
exclusively to the authorities and does not
include any warranty of any properties.
Technical subjects to change.
EN_TK_VU4_REG.doc
05/201010
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

JUNG TKVU4 Operating instructions

JUNG
Brand
JUNG
Model
TKVU4
Category
Door intercom systems
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents