Chevrolet 2008 Tahoe Hybrid Owner's manual

Seats and Restraint System

............................. 1-1

Front Seats

............................................... 1-2

Restraint System Check

.............................. 1-3

Features and Controls

..................................... 2-1

Storage Areas

........................................... 2-2

Starting and Operating Your Vehicle

............. 2-3

Instrument Panel

............................................. 3-1

Climate Controls

........................................ 3-2

Warning Lights, Gages, and Indicators

.......... 3-3

Driver Information Center (DIC)

.................. 3-11

Audio System(s)

....................................... 3-13

Driving Your Vehicle

....................................... 4-1

Your Driving, the Road, and Your Vehicle

..... 4-2

Towing

..................................................... 4-2

Service and Appearance Care

.......................... 5-1

Service

..................................................... 5-2

Checking Things Under the Hood

................. 5-3

Bulb Replacement

.................................... 5-21

Electrical System

...................................... 5-22

Tires

...................................................... 5-24

Capacities and Speciﬁcations

..................... 5-42

Maintenance Schedule

..................................... 6-1

Maintenance Schedule

................................ 6-2

Index

................................................................ 1

2008 Chevrolet Tahoe and GMC Yukon Two-Mode Hybrid M

Preface

GENERAL MOTORS, GM and the GM Emblem,

CHEVROLET, the CHEVROLET Emblem, GMC, the

GMC Emblem, and the names TAHOE and YUKON are

registered trademarks of General Motors Corporation.

The information in this manual supplements the

owner manual. This manual includes the latest

information at the time it was printed. GM reserves the

right to make changes after that time without further

notice.

Keep this manual in the vehicle for quick reference.

Introduction

Your hybrid SUV is designed to be more fuel efficient

than the standard SUV, which results in reduced carbon

dioxide emissions.

Warranty Information

Two-Mode Hybrid Speciﬁc Warranty

This information supersedes the Hybrid Speciﬁc

Warranty found in the Limited Warranty and Owner

Assistance Information booklet furnished with your

new vehicle.

For vehicles sold in the United States, in addition to the

Bumper-to-Bumper Coverage described in the Limited

Warranty and Owner Assistance manual, General Motors

will warrant certain Hybrid components for each

2008 Chevrolet Tahoe Two-Mode Hybrid and GMC

Yukon Two-Mode Hybrid (hereafter referred to as Hybrid)

for 8 years or 100,000 miles (160 000 kilometres),

whichever comes ﬁrst, from the original in-service date of

the vehicle, against warrantable repairs to the speciﬁc

Hybrid components of the vehicle.

Litho in U.S.A.

Part No. 15118085 A First Printing

©

ii

For vehicles sold in Canada, in addition to the Complete

Vehicle Coverage described in the GM Canadian Limited

Warranty, Maintenance and Owner Assistance booklet,

General Motors of Canada Limited will warrant certain

Hybrid components for each 2008 Chevrolet Tahoe

Two-Mode Hybrid and GMC Yukon Two-Mode Hybrid

(hereafter referred to as Hybrid) for 8 years, or

160,000 kilometres, whichever comes ﬁrst, from the

original in-service date of the vehicle, against warrantable

repairs to the speciﬁc Hybrid components of the vehicle.

This warranty is for Hybrid vehicles registered in the

United States or Canada, and normally operated in the

United States or Canada. In addition to the initial owner of

the vehicle, the coverage described in this Hybrid

warranty is transferable at no cost to any subsequent

person(s) who assumes ownership of the vehicle

within the above described 8 years or 100,000 mile

(160 000 kilometres) term. No deductibles are associated

with this Hybrid warranty.

This Hybrid warranty is in addition to the express

conditions and warranties described in the Limited

Warranty and Owner Assistance manual. The coverage

and beneﬁts described under “New Vehicle Limited

Warranty” are not extended or altered because of this

special Hybrid Component Warranty.

For 2008 Hybrid owners requiring more comprehensive

coverage than that provided under this Hybrid warranty, a

GM Protection Plan may be available. See your dealer for

more details.

What is Covered

This Hybrid warranty covers repairs to correct any

vehicle defect related to materials or workmanship

occurring during the 8 year or 100,000 miles

(160 000 kilometres) term for the following:

Transmission

Automatic transmission components including the

transmission auxiliary ﬂuid pump, transmission auxiliary

pump controller, and 3 phase transmission cables.

Brakes

Brake modulator.

Other Hybrid Components

Battery pack, 300v cables, Drive Motor/Generator

Control Module (DMCM) and Accessory Power Module.

Towing

During the 8 year or 100,000 mile (160 000 kilometres)

Hybrid warranty period, towing is covered to the nearest

servicing dealer if your vehicle cannot be driven because

of a warranted defect. Contact the Roadside Assistance

Center for towing. Refer to the owner manual for details.

Roadside Assistance is not part of or included in the

coverage provided by the new Vehicle Limited Warranty.

General Motors and General Motors of Canada Limited

reserve the right to make any changes or discontinue the

Roadside Assistance program at any time without

notiﬁcation.

iii

Courtesy Transportation

During the 8 year or 100,000 mile (160 000 kilometres)

Hybrid warranty period, interim transportation is available

under the Courtesy Transportation Program. Consult your

dealer for details.

Courtesy Transportation is not a part of the New Vehicle

Limited Warranty. The Limited Warranty and Owner

Assistance Information booklet furnished with the vehicle

provides detailed warranty coverage information.

General Motors reserves the right to unilaterally modify,

change, or discontinue Courtesy Transportation at any

time and to resolve all questions of claim eligibility

pursuant to the terms and conditions described herein at

its sole discretion.

What is Not Covered

In addition to the “What is Not Covered” section of the

warranty booklet, this Hybrid warranty does not cover the

following items:

Wear Items

Wear items, such as brake linings, are not covered in

this Hybrid warranty.

Maintenance

As the vehicle owner, you are responsible for the

performance of the scheduled maintenance listed in your

owner manual. Maintenance intervals, checks,

inspections, and recommended ﬂuids and lubricants as

prescribed in the owner manual are necessary to keep

your vehicle in good working condition. Any damage

caused by owner/lessee failure to follow scheduled

maintenance may not be covered by warranty. Scheduled

maintenance includes such items as:

• Brake Pads/Linings

• Coolants and Fluids

• Filters

Using this Supplement

This supplement contains information speciﬁc to the

hybrid components of the vehicle. It does not explain

everything you need to know about the vehicle.

Read this supplement along with the owner manual to

learn about the vehicle’s features and controls.

Index

A good place to look for what you need is the Index in

back of this supplement. It is an alphabetical list of

what is in the supplement, and the page number where

you will ﬁnd it.

iv

Front Seats ......................................................1-2

Power Seats ..................................................1-2

Manual Lumbar ..............................................1-2

Manual Reclining Seatback ..............................1-2

Restraint System Check ...................................1-3

Replacing Restraint System Parts After a

Crash ........................................................1-3

Section 1 Seats and Restraint System

1-1

Front Seats

Power Seats

A. Power Seat Adjustment Control

B. Manual Lumbar Control

C. Manual Reclining Seatback Lever

Adjust the seat forward or rearward by sliding the

control (A) forward or rearward.

Your vehicle may have additional features to adjust your

vehicle’s power seat:

• Raise or lower the front part of the seat cushion by

moving the front of the control up or down.

• Raise or lower the entire seat by moving the entire

control up or down.

Manual Lumbar

Increase or decrease lumbar support by turning the

control (B) forward or rearward.

Manual Reclining Seatback

To recline the seatback:

1. Lift the reclining seatback lever (C).

2. Move the seatback to the desired position, then

release the lever to lock the seatback in place

3. Push and pull on the seatback to make sure it is

locked.

1-2

To return the seatback to an upright position:

1. Lift the lever fully without applying pressure to the

seatback and the seatback will return to the

upright position.

2. Release the lever to lock the seatback in place.

3. Push and pull on the seatback to make sure

it is locked.

Restraint System Check

Replacing Restraint System Parts

After a Crash

If an airbag inﬂates or the vehicle has been in a crash,

the vehicle’s sensing system may command the

automatic hybrid battery disconnect to open. The battery

will disconnect. The hybrid battery will be off and the

vehicle will not start. The airbag readiness light and/or

SERVICE HYBRID SYSTEM message may come on in

the driver information center. See “Airbag Readiness

Light” in the owner manual and Driver Information Center

(DIC) on page 3-11 for more information.

To operate the vehicle, the automatic hybrid battery

disconnect must be reconnected by a qualiﬁed service

technician and sensing system parts will need to be

replaced. Have the vehicle serviced right away.

1-3

✍ NOTES

1-4

Storage Areas ..................................................2-2

Power Outlet Alternating Current .......................2-2

Starting and Operating Your Vehicle .................2-3

Starting Your Vehicle ......................................2-3

Automatic Transmission Operation ....................2-6

Regenerative Braking ......................................2-9

Running the Vehicle While Parked ..................2-10

Section 2 Features and Controls

2-1

Storage Areas

Power Outlet Alternating Current

Your vehicle may have a power outlet that can be used

to plug in electrical equipment that uses a maximum

limit of 150 watts.

The power outlet is located

in the rear cargo area on

the driver side.

An indicator light on the outlet turns on to show it is in

use. The light comes on when the ignition is in ON/RUN

and equipment requiring less than 150 watts is

plugged into the outlet, and no system fault is detected.

The indicator light does not come on when the ignition

is in LOCK/OFF or if no equipment is plugged into

the outlet.

If you try to connect equipment using more than

150 watts or a system fault is detected, a protection

circuit shuts off the power supply and the indicator light

turns off. To reset the circuit, unplug the item and plug it

back in or turn the Retained Accessory Power (RAP) off

and then back on. The power restarts when equipment

using 150 watts or less is plugged into the outlet and a

system fault is not detected.

The power outlet is not designed for the following

electrical equipment and may not work properly if these

items are plugged into the power outlet:

• Equipment with high initial peak wattage such as:

compressor-driven refrigerators and electric

power tools.

• Other equipment requiring an extremely stable

power supply such as: microcomputer-controlled

electric blankets, touch sensor lamps, etc.

See High Voltage Devices and Wiring on page 5-3.

2-2

Starting and Operating Your

Vehicle

Starting Your Vehicle

{CAUTION:

Exiting your vehicle, without ﬁrst shifting into

PARK (P), may cause the vehicle to move,

and you or others can be seriously injured.

CAUTION: (Continued)

Because your vehicle has the Automatic Engine

Start/Stop feature, the vehicle’s engine might

seem to be shut off when you come to a

complete stop. However, once the brake pedal

is released, the vehicle can move. The vehicle’s

engine can also restart at any time.

Shift to PARK (P) and turn the ignition to

LOCK/OFF, before exiting the vehicle.

Start the engine as you would any other engine. See

“Starting Your Engine” in the owner manual for more

information on starting. The hybrid system provides very

quiet engine starting. If pulling a trailer with trailer brakes,

see Towing a Trailer on page 4-2 for more information.

2-3

Auto Stop

The vehicle has an Auto Stop feature. After a successful

engine start, the Hybrid Powertrain Control Module

(HPCM) may turn off the engine and operate in the Auto

Stop mode. Some of the vehicle conditions that allow the

engine to stop running and enter the Auto Stop mode are:

• Ignition switch is in the ON/RUN position.

• The hood is closed.

• The gear selector is in PARK (P), NEUTRAL (N) or

DRIVE (D).

• The hybrid battery is at an acceptable state of

charge.

• The hybrid battery voltage, temperature or power

limits are not exceeded. In very hot conditions, Auto

Stop may be unavailable until the hybrid battery has

cooled.

• The engine is at operating temperature.

If you are on an incline, the hybrid drive motor can help

keep your vehicle from rolling backwards, even if the

engine is in Auto Stop.

With your foot off the brake and the vehicle on level

ground, the hybrid drive motor may cause your vehicle to

roll slowly forward, even when the engine is in Auto Stop.

To be sure your vehicle will not move or roll, always

keep your foot ﬁrmly on the brake pedal until you

are ready for the vehicle to move.

Engine OFF and AUTO STOP modes are indicated on

the tachometer display. When the tachometer needle

indicates OFF, the engine is not running and will remain

off until the ignition key is placed in the START position or

a remote vehicle start is performed. When the tachometer

needle indicates AUTO STOP, the engine is not running

but may Auto Start at any time without notice. See

Tachometer on page 3-4 for more information.

A chime will sound if the driver door is opened while in

Auto Stop as a reminder that the ignition switch is not in

the LOCK/OFF position. Always turn the ignition switch to

LOCK/OFF and remove the key from the ignition switch

when exiting the vehicle.

2-4

Auto Start

The vehicle also has an Auto Start feature. The engine

will remain off while in Auto Stop mode until vehicle

conditions require the engine to run. The near-instant

starting of the engine from Auto Stop mode is called

Auto Start. Some of the vehicle conditions that

may cause the HPCM to Auto Start the engine are:

• The hood is opened.

• The gear selector is in MANUAL MODE (M) or

REVERSE (R).

• The hybrid battery state of charge is too low.

• The hybrid battery voltage, temperature or power

limits are exceeded.

• The engine is not at operating temperature.

• Acceleration demands require the use of the engine.

EV Mode

The vehicle also has an EV mode which uses only the

electric motor to move the vehicle. Depending on

the state of battery charge, the vehicle can travel up to

two miles in EV mode. EV mode is unavailable when

the vehicle is out of fuel.

While lightly accelerating, the vehicle will be propelled in

EV mode.

If increased acceleration is required, or the vehicle

achieves a speed of approximately 25 mph (40 km/h),

the engine will start automatically. The engine will

shut off at speeds below 25 MPH (40 km/h) unless the

transmission is in MANUAL MODE (M) or Auto Stop

is disabled.

During heavy acceleration, both the engine and hybrid

electric motors supply power. A sensation similar to a

transmission gear change can be felt as the transmission

changes modes. Engine RPM may remain above

4,000 RPM for a longer period during hard acceleration.

2-5

Automatic Transmission Operation

Your vehicle has an M99–EVT transmission, and has an

electronic shift position indicator within the instrument

panel cluster. The electronic shift position indicator

displays when the shift lever is moved out of PARK (P).

There are several different positions for the shift lever.

See ““Range Selection Mode” later in this section.

PARK (P): This position locks the rear wheels. It is the

best position to use when you start your engine

because the vehicle cannot move easily.

When parked on a hill, especially when the vehicle has a

heavy load, you may notice an increase in the effort to

shift out of PARK (P). See “Shifting Into PARK (P)” in the

Index of vehicle’s owner manual for more information.

{CAUTION:

It is dangerous to get out of your vehicle if the

shift lever is not fully in PARK (P) with the

parking brake ﬁrmly set. Your vehicle can roll.

Do not leave your vehicle when the engine is

running unless you have to. If you have left the

engine running, the vehicle can move suddenly.

You or others could be injured. To be sure your

vehicle will not move, even when you are on

fairly level ground, always set your parking

brake and move the shift lever to PARK (P).

See “Shifting Into Park (P)” in the Owner

Manual.

If you are pulling a trailer, see Towing a Trailer

on page 4-2.

REVERSE (R): Use this gear to back up.

Notice: Shifting to REVERSE (R) while your vehicle

is moving forward could damage the transmission.

The repairs would not be covered by your warranty.

Shift to REVERSE (R) only after your vehicle is

stopped.

2-6

To rock your vehicle back and forth to get out of snow,

ice, or sand without damaging the transmission, see

“If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow” in

the Index of the vehicle’s owner manual.

NEUTRAL (N): In this position, the engine and

transmission are not connected with the wheels. To

restart while the vehicle is already moving, use

NEUTRAL (N) only.

{CAUTION:

Shifting into a drive gear while the engine is

running at high speed is dangerous. Unless

your foot is ﬁrmly on the brake pedal, your

vehicle could move very rapidly. You could

lose control and hit people or objects. Do not

shift into a drive gear while your engine is

running at high speed.

Notice: Shifting out of PARK (P) or NEUTRAL (N)

with the engine running at high speed may damage

the transmission. The repairs would not be covered

by your warranty. Be sure the engine is not running

at high speed when shifting your vehicle.

DRIVE (D): This position is for normal driving. It

provides the best fuel economy for your vehicle. If you

need more power for passing, and you are:

• Going less than about 35 mph (55 km/h), push the

accelerator pedal about halfway down.

• Going about 35 mph (55 km/h) or more, push the

accelerator all the way down.

DRIVE (D) can be used when towing a trailer, carrying a

heavy load, driving on steep hills, or for off-road

driving. You may want to shift the transmission to a

lower gear selection if the transmission shifts too often.

Downshifting the transmission in slippery road

conditions could result in skidding, see “Skidding” under

“Loss of Control” in the Index of the vehicle’s owner

manual.

When temperatures are very cold, the transmission’s

gear shifting may be delayed providing more stable

shifts until the engine warms up. Shifts may be more

noticeable with a cold transmission. This difference

in shifting is normal.

2-7

MANUAL MODE (M): This position lets drivers select

the range of gears appropriate for current driving

conditions. If your vehicle has this feature, see “Range

Selection Mode” later in this section.

Notice: Spinning the tires or holding the vehicle in

one place on a hill using only the accelerator

pedal may damage the transmission. The repair will

not be covered by your warranty. If you are stuck,

do not spin the tires. When stopping on a hill,

use the brakes to hold the vehicle in place.

Your vehicle has a shift stabilization feature that adjusts

the transmission shifting to the current driving conditions

in order to reduce rapid upshifts and downshifts. This shift

stabilization feature is designed to determine, before

making an upshift, if the engine will be able to maintain

vehicle speed by analyzing things such as throttle

position, vehicle load, and hill grade. If the shift

stabilization feature determines that a current vehicle

speed cannot be maintained, the transmission does not

upshift and instead holds the current gear. In some

cases, this may appear to be a delayed shift, however the

transmission is operating normally.

Range Selection Mode

The Range Selection Mode controls the vehicle’s

transmission.

To use this feature, do the following:

1. Move the shift lever to the MANUAL MODE (M).

2. Press the plus/minus button, to upshift or downshift

selecting the desired range of gears for your current

driving conditions.

2-8

While in the MANUAL MODE (M) a number displays next

to the M, indicating the current gear that has been

selected. The number displayed in the gear indicator is

the highest gear that can be used. However, your vehicle

can automatically shift to lower gears as it adjusts to

driving conditions. This means that all gears below that

number are available. When THIRD (3) is selected,

FIRST (1) through THIRD (3) gears are automatically

shifted by the vehicle, but FOURTH (4) cannot be used

until the plus/minus button located on the steering column

lever is used to change to the gear.

The Range Selection Mode controls the vehicle and

engine speed while driving down a hill or towing a trailer,

by allowing you to select a desired range of gears.

When you move the shift lever into M, the transmission

will default to M4. In this gear range, effective engine

braking will occur at speeds above 45 mph (72 km/h).

Pushing the minus (−) button on the shift lever will

change the gear range to M3. In this gear range,

effective engine braking will occur at speeds above

35 mph (56 km/h).

Pushing the minus (−) button on the shift lever will

change the gear range to M2. In this gear range,

effective engine braking will occur at speeds above

25 mph (40 km/h).

Pushing the minus (−) button on the shift lever will

change the gear range to M1. In this gear range,

effective engine braking will occur at speeds above

10 mph (16km/h).

When operating in MANUAL MODE (M), Auto Stop is

disabled. Vehicle efficiency is decreased operating

in MANUAL MODE (M) compared to DRIVE (D).

Cruise control can be used while using the Range

Selection Mode.

Regenerative Braking

Your vehicle uses a hybrid technology known as

regenerative braking. This technology enables the

electric drive motor on your vehicle to operate as

a generator when you are coasting or braking. The

energy of the moving vehicle is used to recharge the

vehicle’s high voltage hybrid battery.

The conventional hydraulic disc brakes on your vehicle

work in partnership with the regenerative braking to

insure effective braking in all situations, such as when the

high voltage hybrid battery is fully charged or a high

braking demand is requested. Four wheel, four channel

ABS allows the vehicle to maintain steering control during

braking and Electronic Stability Control (ESC) helps you

to keep your vehicle in control in unfavorable conditions.

These systems, however, are not a substitute for safe

driving practices.

2-9

The braking system is computer controlled and uses the

information provided by the driver’s input at the brake

pedal to seamlessly blend the regenerative braking with

the conventional hydraulic disc brakes to meet any

requirements for deceleration. The brake controller in

your vehicle has a high pressure accumulator to provide

the hydraulic pressure to the disc brakes in response to

the driver’s input. The controller interprets the braking

request and uses regenerative braking, conventional

hydraulic braking or a combination of both as necessary.

Since the controller applies the hydraulic brakes through

its high pressure accumulator, you may occasionally hear

the motor driven pump in the controller when it runs to

recharge the system. This recharging cycle is normal.

Even though the conventional disc brakes are operated

by the controller, there is still a direct mechanical

connection with the brake pedal and the hydraulic brake

system in the unlikely event of a controller problem. See

“Warning Lights, Gages, and Indicators” and “Driver

Information Center (DIC)” in the Index of the vehicle’s

owner manual. In the event of a controller problem, your

brake pedal may be harder to push and the stopping

distance may be longer.

Running the Vehicle While Parked

It is better not to park with the engine running. But if you

ever have to, here are some things to know.

{CAUTION:

Exiting your vehicle, without ﬁrst shifting into

PARK (P), may cause the vehicle to move, and

you or others can be seriously injured.

Because your vehicle has the Automatic Engine

Start/Stop feature, the vehicle’s engine might

seem to be shut off when you come to a

complete stop. However, once the brake pedal

is released, the vehicle can move. The vehicle’s

engine can also restart at any time.

Shift to PARK (P) and turn the ignition to

LOCK/OFF, before exiting the vehicle.

Follow the proper steps to be sure your vehicle will not

move. See “Shifting Into PARK (P)” in the owner manual

for more information.

If you are pulling a trailer, see Towing a Trailer on

page 4-2 for more information.

2-10

Climate Controls ..............................................3-2

Warning Lights, Gages, and Indicators ..............3-3

Instrument Panel Cluster .................................3-3

Tachometer ...................................................3-4

Charging System Light ....................................3-4

Fuel Economy Gage .......................................3-5

Brake System Warning Light ............................3-5

Anti-lock Brake System (ABS) Warning Light ......3-6

StabiliTrak

®

Indicator Light ...............................3-7

Engine Coolant Temperature Gage ...................3-7

Oil Pressure Gage ......................................... .3-8

Oil Pressure Light ...........................................3-9

Fuel Gage .................................................. .3-10

Driver Information Center (DIC) .......................3-11

DIC Warnings and Messages .........................3-11

Audio System(s) .............................................3-13

Navigation/Radio System ...............................3-13

Section 3 Instrument Panel

3-1

Climate Controls

For more information on the vehicle’s climate control

system, see “Climate Control System” in the owner

manual Index.

Electric Air Conditioning Compressor

This hybrid vehicle has a 300 volt, electrically powered

air conditioning compressor. This allows for continuous

air conditioning operation and passenger comfort,

even while the hybrid engine cycles on and off.

When operating the climate control system, select the

AUTO mode and the desired temperature setting.

The climate control system will automatically adjust the

fan speed and airﬂow direction. The climate control

system continues to adjust the climate control settings

chosen for best use of electrical power.

To get maximum engine off time, select a warmer

temperature setting or turn off the air conditioning to

shut off the compressor. Continuous air conditioning use

can cause the engine to autostart more frequently.

Some noise may be heard occasionally from the

compressor, especially when air conditioning use is high

and the engine has turned off.

3-2

Page is loading ...

Chevrolet 2008 Tahoe Hybrid, 2008, 2008 Tahoe, Tahoe Hybrid 2008 Owner's manual

Related papers

Other documents