Aleratec 280110 User guide

USER GUIDE

Aleratec

DVD/CD RoboRacer LS™

Part No. 280110

www.aleratec.com

Table of Contents

Welcome! ...........................................................................................1

Included Items ..................................................................................1

Product Features ..............................................................................2

Key Items on the DVD/CD RoboRacer LS ......................................2

Installing the Hardware ....................................................................3

Software Installation ........................................................................4

Installing the RoboRacer LS Utility ....................................................... 4

Nero Essentials Installation ....................................................................8

Updating the LightScribe System Software .........................................15

Creating an Image with Nero ................................................................18

Creating an Image from a Source Disc .................................................22

Getting Acquainted with the RoboRacer LS Software .........................24

Using RoboRacer LS to Burn an ISO Disc ..........................................27

LightScribe Labeling ............................................................................ 29

Technical Support Addresses and Phone Numbers ...................33

www.aleratec.com

1

Welcome!

Congratulations on your purchase of an Aleratec DVD/CD

RoboRacer LS, considered by industry experts to be one of the

ﬁnest DVD/CD Duplicators available.

The entire Aleratec team is committed to providing you with

courteous service. Our knowledgeable staff will strive to make

owning and operating your new Aleratec DVD/CD RoboRacer LS

a pleasant experience.

This User Guide will lead you step-by step through the operation

procedures of your DVD/CD duplicator.

We at Aleratec appreciate your selection of our product, and

wish you great success and enjoyment of your new DVD/CD

RoboRacer LS.

Check out Aleratec Online!

• www.aleratec.com

• www.facebook.com/Aleratec

• www.twitter.com/Aleratec

• www.youtube.com/Aleratec

Included Items

• 1 DVD/CD RoboRacer LS

• 1 Disc Output Bin Holder

• 1 100-Disc Capacity Disc Output Bin

• 1 50-Disc Capacity Disc Output Bin

• 4 100-Disc Capacity Guide Rods

• 4 50-Disc Capacity Guide Rods

• 1 USB 2.0 Cable

• 1 Power Cord with Switch

• 1 External Power Supply

• 1 Disc Publishing Software Suite CD

• 1 Nero 7 Essentials CD

www.aleratec.com

2

Product Features

The DVD/CD RoboRacer LS is a versatile robotic desktop DVD/CD

copying and LightScribe printing solution.

• Fully Automatic Disc Publisher

– Fully automatic disc handling

– 100 disc capacity

– Duplicate and LightScribe label

– Unattended operation

Key Items on the

DVD/CD RoboRacer LS

1

2

3

1. Clear Plastic Disc Guide Rods

2. Power and Function Indicator LED

3. LightScribe DVD Recorder

4. Disc Tray Control Arm

5. Disc Input Bin

6. Protective Cover

7. Disc Bin Holder

8. Disc Output Bin

A. Power Plug

B. High Performance Cooling Fan

C. USB 2.0 to the PC

4

5

6

7

8 C A

B

www.aleratec.com

3

Installing the Hardware

1. Remove the DVD/CD RoboRacer LS from the box, plug the power

cord into the end of the external power supply and plug the power

cord into a 110VAC power source. Plug the power supply cord into the

DVD/CD RoboRacer LS and leave the power switch off, (power on the

device after the software has been installed). Place the RoboRacer LS

on a level surface.

2. Attach the USB cable into the PC and the RoboRacer LS.

3. Slide the bin holder into the slot on the left side of the RoboRacer

LS case and place a disc output bin into the bin holder. There are two

output bins included (50 disc capacity, 100 disc capacity). Make sure to

keep the output bins that come with the 280110. Although similar to a

normal disc media cover, the Disc Output Bins are for specic use with

the RoboRacer LS. When installing, make sure that the anges on the

bin are touching the lip of the bin holder. If the bin is not pushed down

as far as it can go, the edge of the bin could interfere with the disc

output. To use the 100 disc bin, the DVD/CD RoboRacer LS should be

placed at the edge of a desk or table. Make sure that the bin does not

touch the edge of the desk or table surface.

4. Take the clear plastic disc guide rods and place them into the 4 holes

in the top of the unit. To load the discs into the input bin, take one disc

and place it horizontally level in the input bin. Now you can load the

rest of the discs. All of the discs need to be level with the sides of the

stack straight.

Note: Choose a Good Location

1. Allow adequate clearance for moving parts.

2. Do not place near heat sources such as radiators or air ducts, or

in a place subject to direct sunlight, excessive dust, mechanical

vibration or shock.

3. Good care will help assure maximum product life. Improper

operating environment and misuse may void the warranty.

www.aleratec.com

4

Software Installation

Installing the RoboRacer LS Utility

1. Load the installation CD in the DVD/CD ROM drive in your PC.

Double-click on RoboRacer LS Utility from the menu. Click “Next” to

begin.

2. Choose where you would like to install the program and click “Next”.

www.aleratec.com

5

3. Choose where you would like the program’s Start menu shortcuts to be

installed and click “Next”.

4. Choose what shortcuts you would like to have created by checking the

check boxes, and click “Next”.

www.aleratec.com

6

Installing the RoboRacer LS Utility - continued

5. Review the installation procedure to make sure that you are installing

what you would like and click “Install”.

6. When installation is complete the setup utility will display the

following:

De-check the box “Launch RoboRacer LS Utility”. Click “Finish” to

complete the software installation.

www.aleratec.com

7

7. If you did not de-check the box and the 280110 was not plugged into

the USB port or the power to the device was turned off then the display

box will show:

www.aleratec.com

8

Nero Essentials Installation

1. Open the Nero installation utility. Click “Install Nero 7 Essentials”.

2. Click “Nero 7 Essentials” again.

www.aleratec.com

9

3. After a short delay, Windows Installer will start the Nero installation Wizard.

When this screen is shown, click “Next”.

4. Agree to the user agreement by checking the checkbox in the lower left

corner. Then click “Next”.

www.aleratec.com

10

Nero Essentials Installation - continued

5. At this screen, ll out the elds you would like. When nished clicked

“Next”. Leave the Serial Number that is automatically displayed.

6. Choose the “Custom” option and click “Next”.

www.aleratec.com

11

7. Select the languages you want to be supported and click “Next” on this

screen.

8. Select only “Nero Express Essentials” and “Nero CoverDesigner”, then

click “Next”.

www.aleratec.com

12

Nero Essentials Installation - continued

9. When the nal setup is complete, click “Install” to begin the installation

process.

10. During the installation process this screen will be displayed.

www.aleratec.com

13

11. Near the end of the installation process, this screen will appear asking

if you would like to install any shortcuts. Check the boxes of the

shortcuts you would like and then click “Next”.

12. When installation is complete this screen will appear. Click “Finish” to

exit back to the installer display.

www.aleratec.com

14

Nero Essentials Installation - continued

13. Once back to this screen, click “Exit”.

14. You can now exit this screen as well by clicking “Exit”. You are ready

to use the RoboRacer LS.

www.aleratec.com

15

Updating the LightScribe System Software

1. To install the LightScribe Utility needed to use the LightScribe feature

of the 280110 click on the LS installer.

2. Choose the “Run” option on the Windows security warning to allow the

installer to begin.

3. The installer will begin by extracting the installer.

www.aleratec.com

16

Updating the LightScribe System Software - continued

4. When extraction is complete The InstallShield Wizard will begin.

Click the “Next” button.

5. Agree to the License Agreement by choosing the upper bubble and

click the “Next” button.

Page is loading ...

Aleratec 280110 User guide

Aleratec 280110 User guide

Related papers

Other documents