2. Computers & electronics
  3. Networking
  4. Network media converters
  5. CTC Union
  6. FMC-1000S
FMC-1000S

CTC Union FMC-1000S, FMC-1000S-DC User manual

  • Hello! I am an AI chatbot trained to assist you with the CTC Union FMC-1000S User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What are the power options for the FMC-1000S fiber media converter?
    What types of Ethernet connectors does the FMC-1000S have?
    What type of fiber optic connector does the FMC-1000S have?
    What is the maximum fiber distance supported by the FMC-1000S?
    What LED indicators are available on the FMC-1000S?
    What is the operating temperature range for the FMC-1000S?
    What is the storage temperature range for the FMC-1000S?
    What is the humidity range for the FMC-1000S?
    What are the dimensions of the FMC-1000S?
Description
FMC-1000S provides a cost eff
ective
solution for Fast and
Gigabit Ethernet fiber
media conversion. By utilizing industry
standard SFP modules, this converter can be utilized with multi-
mode or single mode fibers
with LC connectors as well as single
fiber
(WDM) transceivers. The fib er
port provides 1000M
connection, while the copper UTP port provides 10/100/1000
auto-negotiation to connect to a wide variety of Ethernet devices.
FMC-1000S gives you the freedom to extend your
10/100/1000Mbps cabling distance by allowing connectivity up to
120KM over fiber. Five LED indicators signal the power status, UTP
link & speed and fiber link & speed.
Features
■
10/100/1000Base-T to 1000Base-X SFP Converter
■
Auto-Negotiation
■
Auto MDI/MDIX
■
Forward 2048 bytes (Max.) packets
■
Supports IEEE 802.1Q Tag VLAN pass thru
■
Supports Q in Q double tagged frame transparent
■
Supports flow
control
User Guide
10/100/1000Base-T to 1000Base-X
Fiber Media Converters
■
FMC-1000S
■
FMC-1000S-AC, FMC-1000S-DC
Panel
■
Figure #1. FMC-1000S (Adapter Type)
DC Jack
■ Figure #2.
Fiber
Connector
LEDs
Ethernet
Connector
Specifications
Standards
IEEE802.3 10Base-T, IEEE802.3u 100Base-TX,
IEEE802.3ab 1000Base-TX, IEEE802.3z 1000Base-SX/LX
N-Way Auto Negotiation
10/100/1000Base-TX RJ-45 Connectors
One RJ-45 connector is provided for connection to either MDI-X (To PC) or MDI (To HUB)
equipment. Utilizing Auto MDI/MDIX allows all UTP connections to be made using only a
common straight-through UTP cable.
RJ-45 Pin 568-A type 568-B type
FMC-1000S-AC (Power Built-in Type)
5 Pair1-Tip Pair1-Tip
4 Pair1-Ring Pair1-Ring
3 Pair2-Tip Pair3-Tip
6 Pair2-Ring Pair3-Ring
1 Pair3-Tip Pair2-Tip
2 Pair3-Ring- Pair2-Ring
7 Pair4-Tip Pair4-Tip
8 Pair4-Ring Pair4-Ring
1000Base-TX UTP Cable
Cable type: 1000Base-TX; 8 pair, Cat. 5, EIA/TIA-568, STP/UTP
Maximum cable distance: 100 meters (328 feet)
FMC-1000S-DC (Power Built-in Type)
DC Terminal
Fiber Optic Connectors
One connector is provided for fiber
optic cable connection. FMC-1000S is SFP Slot LC
connector.
Environment
Operating: 0°C ~50°C, Storage: -10°C ~70°C
Humidity: 10%~90% (non-condensing)
Power
Adapter Type: Adapter Output 12VDC 0.5A
Built-in AC Power: Input 100~240VAC ±10%
Built-in DC Power: Input 18~60VDC
Dimensions: (W x D x H) mm
FMC-1000S: 73.4 × 108 × 23 FMC-1000/AC: 73.4 × 135 × 23 FMC-1000/DC: 73.4 × 135 × 23
V.: 1.4
LED Indicators
LED
State
Status
PWR
ON (Green)
Power On
FX Link
ON (Green)
Fiber Optical Link
LAN Link
ON (Green)
UTP Link
LAN Speed
ON (Yellow)
1000Mbps
ON (Green)
100Mbps
OFF
10Mbps
FX Speed
ON (Yellow)
1000Mbps
Installation
Connect the Ethernet cable to the FMC-1000S. The converter
will sense whether to operate in Full or Half mode and will be
indicated on the LED. Follow the connection examples below.
Install the fiber converter with the DC power adapter, AC, or
DC power cord.
Connections
The following example illustrates the connection scheme when
connecting from a 10, 100, 1000Base-TX port of one HUB to a
1000Base-X port of another HUB through the fiber.
The following example illustrates the connection scheme when
connecting from a 10/100/1000Base-TX port of one HUB to a
10/100/1000Base-TX Network Interface Card (NIC) in a
computer through the fiber converter.
Wall Mounting Option
FMC standalone wall mount type converters have the option of
adding wall mount capability. One wall mount kit is required for
installing a single standalone unit on the wall. Each wall mount
kit provides all the necessary hardware for a complete
installation.
MEMO:
■
Figure 1. Standalone AC Adapter Type
■
Figure 2. Standalone AC / DC Power Built-in Type
V.: 1.4
/