Total UTC120242 is a compressor designed for generating compressed air for tools operated by compressed air. The compressor has a pressure vessel with a capacity of 24 liters and a maximum pressure of 8 bar. It is equipped with an oil-lubricated pump and has a power of 2 HP (1.5 kW). The compressor is mobile and has wheels for easy transportation. It is also equipped with a pressure switch, a safety valve, and a quick-lock coupling. The compressor is suitable for a wide range of applications, including inflating tires, powering air tools, and painting.
Total UTC120242 is a compressor designed for generating compressed air for tools operated by compressed air. The compressor has a pressure vessel with a capacity of 24 liters and a maximum pressure of 8 bar. It is equipped with an oil-lubricated pump and has a power of 2 HP (1.5 kW). The compressor is mobile and has wheels for easy transportation. It is also equipped with a pressure switch, a safety valve, and a quick-lock coupling. The compressor is suitable for a wide range of applications, including inflating tires, powering air tools, and painting.
AIR COMPRESSOR
TC120242 UTC120242
TC125502 UTC125502
Warning!
When using compressors, basic safety precautions should always be followed to
reduce the risk of fire, electric shock and personal injury.
Read all these instructions before attempting to operate this product.
Keep these instructions with the compressor.
Save these instructions for future reference.
Use Personal Protection Safety Equipment
The compressor ejects high-pressure air. Always wear protective eye goggles
and avoid contact with air outlets Protect eyes with safety glasses or goggles –
use safety glasses or goggles which conform to CE equivalent that provide
protection from the front and side.
Note the instructions for use!
Wear ear muffs!
Ꮯ
Beware of electrical voltage
Ꮨ
Beware of hot parts
Wear goggles!
1
11
10
3
12
1
5
4
6
9
8
2
13
2 3
11
12
8
13
9
1
6
7
4 5
A B
A) Important! To drain the condensation water completely, tilt the compressor to the side.
B) Condensation water: Let out the condensation water daily by opening the drain valve (bottom of the pressure vessel).
1. Layout (Fig. 1/2/3)
1. Intake air filter
2. Pressure vessel
3. Wheel
4. Drainage screw for condensation water
5. Supporting foot
6. Oil drain plug / sight-glass
7. Safety valve
8. Quick-lock coupling
9. Oil sealing plug (oil filler opening)
10.Transportation handle
11.ON/OFF switch
12.Pressure switch
13.Pressure gauge (for reading the tank pressure)
Important!
When using the equipment, a few safety precautions must
be observed to avoid injuries and damage. Please read the
complete operating manual with due care. Keep this manu-
al in a safe place, so that the information is available at all
times. If you give the equipment to any other person, give
them these operating instructions as well.
We cannot accept any liability for damage or accidents
which arise due to a failure to follow these instructions and
the safety instructions.
2. Scope of use
The compressor is designed for generating compressed air
for tools operated by compressed air.
3. Points to note when setting up the com-
pressor
Examine the machine for signs of transit damage. Re-
port any damage immediately to the company which de-
livered the compressor.
Before you put the compressor into operation, check the
oil level in the compressor pump.
The compressor should be set up near the working con-
sumer.
Avoid long air lines and long supply lines (extensions).
Make sure the intake air is dry and dust-free.
Do not set up the compressor in damp or wet rooms.
The compressor may only be used in suitable rooms
(with good ventilation and an ambient temperature from
+5°C to +40°C). There must be no dust, acids, vapors,
explosive gases or inflammable gases in the room.
The compressor is designed to be used in dry rooms. It
is prohibited to use the compressor in areas where work
is conducted with sprayed water.
4. Safety instructions
4.1 General safety instructions
Important! The following basic safety precautions
have to be taken when using this compressor in order
to guard against the risk of electric shock, injury and
fire. Read and note these instructions before you use
the compressor.
1. Keep your work area tidy
- There is a higher risk of accident in an untidy work
area.
2. Make allowance for environmental conditions
- Never leave the compressor in the rain. Never use the
compressor in damp or wet conditions. Provide good
lighting. Never use the compressor near combustible li-
quids or gases.
3. Protect yourself from electric shocks
- Avoid physical contact with earthed parts, e.g. pipes,
radiators, cookers, refrigerators.
4. Keep children away!
- Do not allow other persons to touch the compressor or
its cable. Keep them out of your work area.
5. Keep your compressor in a safe place
- When the compressor is not being used it should be
kept in a dry, locked room out of the reach of the child-
ren.
6. Do not overload your compressor
- It is better and safer to work within the quoted power
range.
7. Wear suitable work clothes
- Do not wear loose garments or jewellery. There is a
risk of them catching on moving parts. Rubber gloves
and non-slip shoes are recommended when working ou-
tdoors. Put on a hair net if you have long hair.
8. Never use the cable for any purpose other than that
intended
Never tow the compressor by its cable and never pull
the power plug out of the socket by the cable. Protect
the cable from heat, oil and sharp edges.
9. Look after your compressor
- Keep your compressor clean so that it works well and
reliably. Follow the maintenance instructions. Check the
power plug and cable regularly and have them re-
placed by a specialist if you discover any damage.
Check any extension cables regularly and replace if da-
maged.
10.Pull out the power plug
- Whenever the compressor is not being used and befo-
re carrying out any maintenance work.
11.Avoid accidental starts
- Make sure that the switch is turned to OFF before you
connect the compressor to the power supply.
12.Extension cables for outdoor use
- Use extension cables outdoors only if they are appro-
ved and marked accordingly.
13.Concentrate at all times
- Watch your work. Be sensible. Do not use the com-
pressor if your mind is not on your work.
14.Examine your compressor for signs of damage
- Before you use the compressor again, carefully check
its safety devices or any slightly damaged parts to make
sure that they are working properly and as intended.
Check moving parts to make sure that they are in good
working order and are not jammed or damaged. All
parts have to be properly fitted in order to be sure of
OGGVKPICNNVJGOCEJKPGUTGSWKTGOGPVU&COCIGFUC
fety devices and parts have to be repaired or replaced
D[CEWUVQOGTUGTXKEGYQTMUJQRWPNGUUQVJGTYKUGUVC
VGFKPVJKUOCPWCN&COCIGFUYKVEJGUJCXGVQDGTGRNC
EGFD[CEWUVQOGTUGTXKEGYQTMUJQR&QPQVWUGCP[
VQQNUYKVJCUYKVEJVJCVECPPQVDGVWTPGFQPCPFQHH
Important!
(QT[QWTQYPUCHGV[WUGQPN[UWEJCEEGUUQTKGUCPF
CWZKNKCT[GSWKROGPVCUCTGNKUVGFKPVJKUOCPWCNQTYJKEJ
CTGTGEQOOGPFGFCPFURGEKHKGFD[VJGOCPWHCEVWTGT
There is a high risk of suffering a serious accident if you
WUGVQQNUQTCEEGUUQTKGUYJKEJCTGPQVNKUVGFKPVJKUOC
PWCNQTKPVJGECVCNQIWGQHTGEQOOGPFGFVQQNUCPFCE
EGUUQTKGU
Have an electrician carry out repairs
4GRCKTUCTGVQDGECTTKGFQWVQPN[D[CSWCNKHKGFGNGEVTK
EKCP+HPQVVJGWUGTOC[UWHHGTUGTKQWUCEEKFGPVU
Noise
7UGGCTOWHHUYJGP[QWWUGVJGEQORTGUUQT
Replacing the power cable
6QRTGXGPVKPLWT[FCOCIGFRQYGTECDNGUOC[QPN[DG
TGRNCEGFD[VJGOCPWHCEVWTGTQTCSWCNKHKGFGNGEVTKEKCP
4.2 Safety instructions for working with
compressed air and blasting guns
Compressors and lines reach high temperatures during
QRGTCVKQP#XQKFEQPVCEV4KUMQHDWTPU
Gases or vapours drawn in by the compressor have to
DGMGRVHTGGQHEQPUVKVWGPVUVJCVOC[ECWUGHKTGQTGZRNQ
UKQPUKPUKFGVJGEQORTGUUQT
9JGP[QWFKUEQPPGEVVJGJQUGEQWRNKPIJQNFVJGEQW
pling element in your hand to prevent injury from the
YJKRNCUJKPIJQUG
9GCTIQIINGUYJGPYQTMKPIYKVJVJGDNQYQWVIWP+PLW
ries may easily result from foreign bodies and blasted
RCTVU
0GXGTRQKPVVJGDNQYQWVIWPCVQVJGTRGTUQPUCPFPG
XGTWUGKVVQENGCPENQVJGUVJCVCTGUVKNNDGKPIYQTP
4.3. Safety information for paint spraying
0GXGTRTQEGUURCKPVUQTUQNXGPVUYKVJCHNCUJRQKPVDG
NQYu%
0GXGTJGCVRCKPVUQTUQNXGPVU
+VKUKORGTCVKXGVQWUGHKNVGTKPIGSWKROGPVHCEGOCUMU
YJGPRTQEGUUKPIJCTOHWNNKSWKFU0QVGCNUQVJGKPHQTOC
VKQPEQPEGTPKPIUCHGV[RTGECWVKQPURWDNKUJGFD[VJGOC
PWHCEVWTGTUQHVJGUGNKSWKFU
Smoking is prohibited during the spraying operation and
KPVJGYQTMTQQO2CKPVXCRQWTUCTGJKIJN[HNCOOCDNG
Make sure there are no open fires or open lights in the
YQTMTQQO5RCTMKPIOCEJKPGUCTGPQVVQDGWUGF
&QPQVMGGRQTEQPUWOGHQQFCPFFTKPMKPVJGYQTM
TQQO2CKPVXCRQWTUCTGJCTOHWN
The work room has to be bigger than 30 m3and have
UWHHKEKGPVXGPVKNCVKQPHQTURTC[KPICPFFT[KPI0GXGT
URTC[KPVQVJGYKPF
+VKUCNYC[UKORGTCVKXGVQQDUGTXGVJGTGIWNCVKQPUQH[QWT
local police authorities when spraying combustible or
JC\CTFQWUUWDUVCPEGU
0GXGTRTQEGUUOGFKCUWEJCUYJKVGRGVTQNGWOURKTKVDW
V[NCNEQJQNCPFOGVJ[NGPGEJNQTKFGYKVJVJG28%RTGUUW
TGJQUGTGFWEGFNKHGURCP
4.4 Operating pressure vessels
#PQRGTCVQTQHCRTGUUWTGXGUUGNKUTGSWKTGFVQMGGRVJG
RTGUUWTGXGUUGNKPIQQFYQTMKPIQTFGTVQQRGTCVGKVRTQ
RGTN[VQUWRGTXKUGKVUWUGVQECTT[QWVGUUGPVKCNOCKPVG
PCPEGCPFTGRCKTYQTMKOOGFKCVGN[CPFVQKPVTQFWEGGU
UGPVKCNUCHGV[OGCUWTGUCEEQTFKPIVQTGSWKTGOGPVU
6JGUWRGTXKUQT[CWVJQTKVKGUOC[QTFGTGUUGPVKCNUCHGIW
CTFUHTQOECUGVQECUG
#RTGUUWTGXGUUGNOC[PQVDGQRGTCVGFKHKVJCUCP[FG
fects which constitute a danger to employees or third
RCTVKGU
The pressure vessel must be regularly inspected for
FCOCIGGITWUV+H[QWFKUEQXGTCP[FCOCIGVJGP
RNGCUGEQPVCEVVJGEWUVQOGTUGTXKEGYQTMUJQR
Keep these safety instructions in a safe place.
5. Assembly and starting
Important!
You must fully assemble the appliance before using it
for the first time.
5.1 Fitting the wheels (3)
(KVVJGUWRRNKGFYJGGNUCUUJQYPKP(KI
5.2 Fitting the supporting foot (5)
(KVVJGUWRRNKGFTWDDGTUVQRRGTCUUJQYPKP(KI
5.3 Fitting the air filter (1)
4GOQXGCNNVJGVTCPURQTVCVKQPUVQRUYKVJCUETGYFTKXGTQT
UKOKNCTCPFHCUVGPVJGCKTHKNVGTUGEWTGN[VQVJGCRRNKCPEG
YKVJVJGUETGYU
5.4Replacing the oil sealing plug (9)
4GOQXGVJGVTCPURQTVCVKQPEQXGTHTQOVJGQKNHKNNGTQRGPKPI
YKVJCUETGYFTKXGTCPFKPUGTVVJGUWRRNKGFUGCNKPIRNWI
KPVQVJGQKNHKNNGTQRGPKPI
5.5 Voltage
$GHQTG[QWWUGVJGOCEJKPGOCMGUWTGVJCVVJGOCKPU
XQNVCIGEQORNKGUYKVJVJGURGEKHKECVKQPUQPVJGTCVKPIRNCVG
.QPIUWRRN[ECDNGUGZVGPUKQPUECDNGTGGNUGVEECWUGC
FTQRKPXQNVCIGCPFECPKORGFGOQVQTUVCTVWR+PVJGECUG
QHNQYVGORGTCVWTGUDGNQYu%OQVQTUVCTVWRKULGQRCT
FK\GFCUCTGUWNVQHUVKHHPGUU
5.6 ON/OFF switch (11)
6QUYKVEJQPVJGEQORTGUUQTRWNNQWVVJGTGFMPQD6Q
UYKVEJQHHVJGEQORTGUUQTRTGUUVJGTGFMPQDKPCICKP
(KI
5.7 Setting the pressure switch (12)
6JGRTGUUWTGUYKVEJKUUGVCVVJGHCEVQT[
5YKVEJQPRTGUUWTGDCT
5YKVEJQHHRTGUUWTGDCT
6. Technical data
7. Cleaning and maintenance
Important!
Pull the power plug before doing any cleaning and
maintenance work on the appliance.
Important!
Wait until the compressor has completely cooled
down. Risk of burns!
Important!
Always depressurize the tank before carrying out any
cleaning and maintenance work.
7.1 Cleaning
Keep the safety devices free of dirt and dust as far as
possible. Wipe the equipment with a clean cloth or blow
it with compressed air at low pressure.
We recommend that you clean the appliance immedia-
tely after you use it.
Clean the appliance regularly with a damp cloth and so-
me soft soap. Do not use cleaning agents or solvents;
these may be aggressive to the plastic parts in the ap-
pliance. Ensure that no water can get into the interior of
the appliance.
You must disconnect the hose and any spraying tools
from the compressor before cleaning. Do not clean the
compressor with water, solvents or the like.
7.2 Condensation water
The condensation water must be drained off each day by
opening the drain valve (4) (on the floor of the pressure
vessel).
Important! The condensation water from the pressu-
re vessel will contain residual oil.
Dispose of the condensation water in an environmen-
tally compatible manner at the appropriate collection
point.
7.3 Safety valve (7)
The safety valve has been set for the highest permitted
pressure of the pressure vessel. It is prohibited to adjust
the safety valve or remove its seal. Actuate the safety valve
from time to time to ensure that it works when required.
Pull the ring with sufficient force until you can hear the
compressed air being released. Then release the ring
again.
7.4 Check the oil level at regular intervals
You must be able to see that the oil level on the oil level
gauge (6) is between the red oil level check mark and the
top edge of the oil level window. Changing the oil: Recom-
mended hydraulic oil: SAE 15W/40 or an alternative of the
same quality. It should be refilled for the first time after 100
hours of operation. Thereafter the oil should be drained
and refilled after every 500 hours in service.
7.5 Changing the oil
Switch off the motor and pull the power plug out of the
socket-outlet. After letting off any air pressure you can re-
move the oil drain plug from the compressor pump by un-
screwing. To prevent the oil escaping out of control, hold a
small piece of metal guttering underneath the drain plug to
direct the oil into a container.If any oil still remains inside,
tilt the compressor a little.
Take the old oil to an official old oil disposal station.
If the oil ever escapes, fit the oil drainage screw (6) back
on. Top up with new oil through the oil filler opening (9) un-
til it comes up to the red mark in the oil level window (6).
Then fit the oil sealing plug (9) again.
7.6 Cleaning the intake filter (1)
The intake filter prevents dust and dirt being drawn in. It is
essential to clean this filter after at least every 300 hours in
service. A clogged intake filter will decrease the compres-
compressor by unscrewing the thumb screw on the air fil-
ter. You can then remove the filter from the two halves of
the plastic housing, tap it to remove the dirt and then blast
it down with low pressure compressed air (approx. 3 bar)
before reinserting it.
7.7 Storage
Important!
Pull the mains plug out of the socket and ventilate the ap-
pliance and all connected pneumatic tools. Switch off the
compressor and make sure that it is secured in such a way
that it cannot be started up again by any unauthorized per-
son.
Important!
Store the compressor only in a dry location which is
not accessible to unauthorized persons. Always store
upright, never tilted!
Model TC120242 UTC120242 TC125502 UTC125502
Rated Voltage(V) 220-240 110-120 220-240 110-120
Rated Frequency(Hz) 50 60 50 60
Input power(Kw/PH) 1.5Kw(2HP) 1.5Kw(2HP) 1.8Kw(2.5HP) 1.8Kw(2.5HP)
No load speed(rpm) 2800 3400 2800 3400
Tank ca
p
acit
y(
L/Gal
)
24
(
6.3
)
24
(
6.3
)
50
(
13.2
)
50
(
13.2
)
Max. operating
pressure(Bar/PSI) 8(116) 8(116) 8(116) 8(116)
Air
L/min) 82 82 93 93
Air
L/min) 93 93 119 119
Protection type IP 20 IP 20 IP 20 IP 20
Machine weight(Kg) 21.5 21.5 28 28
9. Possible causes of failure
Problem Cause Solution
The compressor does not start 1. No supply voltage 1. Check the supply voltage, the power plug and
the socket-outlet.
2. Insufficient supply voltage 2. Make sure that the extension cable is not too
long. Use an extension cable with large
enough wires.
3. Outside temperature is too low 3. Never operate with an outside temperature of
below +5°C.
4. Motor is overheated 4. Allow the motor to cool down. If necessary,
remedy the cause of the overheating.
The compressor starts but there is no pressure 1. Leak in the non-return valve 1. Replace the non-return valve
2. The seals are damaged. 2. Check the seals and have any damaged seals
replaced by a service center
3. The drainage screw for
condensation water (4) leaks.
3. Tighten the screw by hand. Check the seal on
the screw and replace if necessary.
The compressor starts, pressure is shown on the
pressure gauge, but the tools do not start.
1. Loose hose connections 1. Check the compressed air hose and tools and
replace if necessary.
2. Leak in a quick-lock coupling 2. Check the quick-lock coupling and replace if
necessary.
8. Disposal and recycling
The unit is supplied in packaging to prevent its being dam-
aged in transit. This packaging is raw material and can
therefore be reused or can be returned to the raw material
system.
The unit and its accessories are made of various types of
material, such as metal and plastic. Defective components
must be disposed of as special waste.
TC120242,UTC120242 Spare Part List
No . No.Part Description Qty Part Description Qty
Crankcase 1
Crankshaft 1
Gasket 1
Crankcasecover 1
Bolt 1
Gasket 1
Oilgauge 1
Bolt 4
Breath 1
Bolt 1
Connectingrod 1
Circlip 2
Pistonpin 1
Piston 1
Pistonring 1
Pistonring 2
Gasket 1
Cylinder 1
Bolt 2
Spring 2
Nut 2
Gasket 1
ValvePlate 2
Valve 2
ValveGasket 1
Gasket 1
Airfilter 1
Bolt 4
Cylinderhead 1
Elbow 1
Nut 1
Capacitance 1
Washer 4
Spring 4
Bolt 4
Cover 1
Bolt 10
Circlip 1
Fan 1
earbearingcrank 1
Stator 1
Bearing 1
Rotator 1
Bearing 1
Oilsealing 1
Tank 1
Nut 2
Washer 2
Wheel 2
Bolt 2
Draincook 1
Bolt 2
Washer 2
Cushionfoot 2
Washer 2
Bolt 2
Handle 1
Pressureswitch 1
Safetyvalve 1
Pressuregauge 1
Connect 1
Regulator 1
Pressuregauge 1
Quickcoupler 1
Unloadingpipe 1
Unloadingnut 1
Checkvalve 1
Exhaustnut 1
Exhaustpipe 1
Electricalwire 1
Plug 1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
No NoPart Description Qty Part Description Qty
Crankcase 1
Crankshaft 1
Gasket 1
Crankcasecover 1
Bolt 1
Gasket 1
Oilgauge 1
Bolt 4
Breath 1
Bolt 1
Connectingrod 1
Circlip 2
Pistonpin 1
Piston 1
Pistonring 1
Pistonring 2
Gasket 1
Cylinder 1
Bolt 2
Spring 2
Nut 2
Gasket 1
ValvePlate 2
Valve 2
ValveGasket 1
Gasket 1
Airfilter 1
Bolt 4
Cylinderhead 1
Elbow 1
Nut 1
Capacitance 1
Washer 4
Spring 4
Bolt 4
Cover 1
Bolt 10
Circlip 1
Fan 1
earbearingcrank 1
Stator 1
Bearing 1
Rotator 1
Bearing 1
Oilsealing 1
Tank 1
Nut 2
Washer 2
Wheel 2
Bolt 2
Draincook 1
Bolt 2
Washer 2
Cushionfoot 2
Washer 2
Bolt 2
Handle 1
Pressureswitch 1
Safetyvalve 1
Pressuregauge 1
Connect 1
Regulator 1
Pressuregauge 1
Quickcoupler 1
Unloadingpipe 1
Unloadingnut 1
Checkvalve 1
Exhaustnut 1
Exhaustpipe 1
Electricalwire 1
Plug 1
TC125502,UTC125502 Spare Part List
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
TC120242,UTC120242 Exploding view
TC120242,UTC120242 Exploding view
1–Ϫϴδϴήϟ ϩΪΣϮϟ 2–ϑΎϘϳϭ ϞϴϐθΗ ΡΎΘϔϣ 3–˯Ϯϩ ΝήΨϣ 4–Ϊί ˯Ϯϩ ΝήΨϣ 5–ΩΪϋ 6–ΏΎΒλ 7–ϩΎϴϣ ΝήΨϣ 8–ϪϠΠϋ 9–ϩέϮγΎϣ 10–ϥΰΧ 11–
–
ϥΎϣ ΏΎΒλ 12ϪΣϭήϣ ˯ΎτϏ
Ϧϴμϟ ϰϓ ϊϨλ ΄θϨϤϟ
TC120242 UTC120242 Air Compressor
˯ϮϩήγϭήΒϤ
TC125502 UTC125502
1
10
9
87
6
3
11
4
5
2
12
AIR COMPRESSOR
T0512.V01
MADE IN CHINA
www.totaltools.cn
TOTAL TOOLS CO.,LIMITED
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
Total UTC120242 User manual
- Category
- Air compressors
- Type
- User manual
Total UTC120242 is a compressor designed for generating compressed air for tools operated by compressed air. The compressor has a pressure vessel with a capacity of 24 liters and a maximum pressure of 8 bar. It is equipped with an oil-lubricated pump and has a power of 2 HP (1.5 kW). The compressor is mobile and has wheels for easy transportation. It is also equipped with a pressure switch, a safety valve, and a quick-lock coupling. The compressor is suitable for a wide range of applications, including inflating tires, powering air tools, and painting.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Toshiba D-R5SU User manual
-
Danby DAC5088M User manual
-
Danby dac12070ee User manual
-
KarliK IWP-1 User manual
-
Daikin CTXG18QVJUS User guide
-
-
Sealife ECOshot User manual
-
High End Systems Wholehog 2 User manual
-
Groupe Brandt UFB180WU Owner's manual
-
Groupe Brandt NFV300M Owner's manual