ParaBody 359101 User manual

Brand
ParaBody
Model
359101
Category
Fitness, gymnastics & weight training
Type
User manual

ParaBody 359101 is designed to be used with home gyms to enhance exercises. It comes with a 20-hole weight stack shaft, weight plate bushings, weight stack labels, and weight plates. To assemble this device, you will need to insert the weight plate bushings into the weight plates, attach the weight stack shaft to the head plate, and insert the guide rods through the weight stack cushions into the base. Then, slide the weight plates down over the guide rods and attach the head plate assembly.

ParaBody 359101 is designed to be used with home gyms to enhance exercises. It comes with a 20-hole weight stack shaft, weight plate bushings, weight stack labels, and weight plates. To assemble this device, you will need to insert the weight plate bushings into the weight plates, attach the weight stack shaft to the head plate, and insert the guide rods through the weight stack cushions into the base. Then, slide the weight plates down over the guide rods and attach the head plate assembly.

359101 50 LB. ADD-ON KIT
Part # 6827301 Revision: 3/30/991
ASSEMBLY INSTRUCTIONS
2
PARTS LIST
PART #
6284501
6382301
KEY
1
2
QTY
1
1
KEY
3
4
PART #
6198501
6214501
DESCRIPTION
WEIGHT STACK LABEL (1-25)
WEIGHT PLATES
QTY
1
5
DESCRIPTION
20 HOLE WEIGHT STACK SHAFT
WEIGHT PLATE BUSHING 10 CT
STEP 1:
• Snap two WEIGHT PLATE BUSHINGS (3) into the top of all five WEIGHT PLATES (6) as shown in FIGURE 1.
FIGURE 1
2
4
3
FIGURE 2
STEP 2:
TOP BOOM or GUIDE ROD SUPPORT
• Remove the WEIGHT STACK SELECTOR PIN from the WEIGHT STACK as shown in FIGURE 2.
• Unthread the CABLE from the WEIGHT STACK SHAFT of the HEAD PLATE as shown in FIGURE 2.
• Remove or loosen the TOP BOOM or GUIDE ROD SUPPORT. (Refer to Home Gym instructions)
• Tilt the GUIDE RODS back and remove the HEAD PLATE ASSEMBLY, fifteen WEIGHT PLATES, two WEIGHT STACK CUSHIONS,
two 3/4” WASHERS, and two WEIGHT STACK SPACERS as shown in FIGURE 1. (NOTE: Please discard the two 3/4” WASHERS,
and the two WEIGHT STACK SPACERS.)
• Unbolt the old WEIGHT STACK SHAFT from the HEAD PLATE. (NOTE: Please discard the old WEIGHT STACK SHAFT.)
HEAD PLATE
GUIDE ROD
WEIGHT STACK SHAFT
WEIGHT STACK PIN
WEIGHT PLATE
WEIGHT STACK CUSHION
3/4” WASHER
WEIGHT STACK SPACER
0
1
2
345
6
1/2 1/2 1/2 1/2 1/2 1/2
4
STEP 4:
FIGURE 3
HEAD PLATE
• SECURELY assemble the 20 HOLE WEIGHT STACK SHAFT
(1) to the HEAD PLATE. (NOTE: The bolt hole in the HEAD
PLATE should be on top.)
• Attach the WEIGHT STACK LABELS (3) (#16-20) to the
five WEIGHT PLATES (4) as shown on FIGURE 3.
• Insert the two GUIDE RODS through the two WEIGHT
STACK CUSHIONS into the base as shown in FIGURE 3.
Lubricate the GUIDE RODS with a silicon or teflon
spray that is available at most hardware stores.
•
USING EXTREME CARE, slide the five new WEIGHT
PLATES (4) and the previous fifteen WEIGHT PLATES
down over the GUIDE RODS onto the WEIGHT STACK
CUSHIONS. (NOTE: Make sure that the key holes of the
WEIGHT PLATES all face the same way.)
• Carefully Slide the new HEAD PLATE ASSEMBLY down
over the GUIDE RODS onto the weight stack as shown in
FIGURE 3.
GUIDE ROD
WEIGHT
STACK
CUSHION
Thank you for purchasing the Parabody 359101 50 LB. ADD-ON KIT. If unsure of proper use of equipment, call your local
LifeFitness distributor or call the Parabody customer service department at (800) 328-9714.
4
3
• Screw the CABLE into the WEIGHT STACK SHAFT of the
HEAD PLATE until the CABLE slightly pulls on the HEAD
PLATE.
• TIGHTEN jam nut securely!
1
• SECURELY tighten all loose connections.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

ParaBody 359101 User manual

Brand
ParaBody
Model
359101
Category
Fitness, gymnastics & weight training
Type
User manual

ParaBody 359101 is designed to be used with home gyms to enhance exercises. It comes with a 20-hole weight stack shaft, weight plate bushings, weight stack labels, and weight plates. To assemble this device, you will need to insert the weight plate bushings into the weight plates, attach the weight stack shaft to the head plate, and insert the guide rods through the weight stack cushions into the base. Then, slide the weight plates down over the guide rods and attach the head plate assembly.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents