Barco Coronis Fusion 4MP (MDCC-4430) User guide

ENABLING BRIGHT OUTCOMES

MDCC-4430 (NC)

MDCC-6530 (NC)

User guide

Coronis Fusion 4MP / 6MP

Registered office: Barco NV

President Kennedypark 35, 8500 Kortrijk, Belgium

www.barco.com/en/support

www.barco.com

Barco NV

Beneluxpark 21, 8500 Kortrijk, Belgium

www.barco.com/en/support

www.barco.com

3R5911227 /04 Coronis Fusion 4MP / 6MP

1 Welcome!.......................................................................................................................................................................................................... 5

1.1 What's in the box................................................................................................................................................................................6

1.2 Product overview................................................................................................................................................................................6

2 Installation .......................................................................................................................................................................................................9

2.1 Display controller installation....................................................................................................................................................10

2.2 Display position adjustment ......................................................................................................................................................10

2.3 Cable connections.......................................................................................................................................................................... 11

2.4 VESA-mount installation.............................................................................................................................................................12

2.5 MXRT driver and Intuitive Workflow Tools installation ...............................................................................................15

2.6 QAWeb registration .......................................................................................................................................................................15

3 Daily operation .........................................................................................................................................................................................17

3.1 Recommendations for daily operation ................................................................................................................................18

3.2 Shortcut bar........................................................................................................................................................................................18

3.3 Standby switching...........................................................................................................................................................................19

3.4 SoftGlow light mode switching ................................................................................................................................................19

3.5 OSD menu access and use ......................................................................................................................................................20

4 Advanced operation............................................................................................................................................................................21

4.1 OSD menu language ....................................................................................................................................................................22

4.2 OSD menu orientation..................................................................................................................................................................22

4.3 OSD menu automatic close function....................................................................................................................................22

4.4 Power lock function........................................................................................................................................................................22

4.5 SoftGlow Task light.........................................................................................................................................................................23

4.6 SoftGlow Wall light .........................................................................................................................................................................23

4.7 DPMS mode.......................................................................................................................................................................................24

4.8 Hibernate .............................................................................................................................................................................................24

4.9 Luminance target ............................................................................................................................................................................25

4.10 Color presets .....................................................................................................................................................................................25

4.10.1 Color temperature.......................................................................................................................................................25

4.10.2 Color coordinates........................................................................................................................................................26

4.11 Color space ........................................................................................................................................................................................26

4.12 Viewing modes .................................................................................................................................................................................26

4.13 Display functions .............................................................................................................................................................................27

4.14 sRGB .....................................................................................................................................................................................................27

Table of contents

R5911227 /04 Coronis Fusion 4MP / 6MP4

4.15 Ambient Light Compensation (ALC).....................................................................................................................................28

4.16 Reading rooms.................................................................................................................................................................................28

4.17 Continuous Ambient Light Compensation (ALC)..........................................................................................................29

4.18 Embedded QA ..................................................................................................................................................................................29

4.18.1 About Embedded QA................................................................................................................................................29

4.18.2 DICOM status report .................................................................................................................................................29

4.18.3 DICOM compliance check .....................................................................................................................................30

4.18.4 DICOM calibration ......................................................................................................................................................30

4.18.5 Reset DICOM calibration........................................................................................................................................31

4.18.6 DICOM error threshold.............................................................................................................................................31

4.19 Image scaling ....................................................................................................................................................................................31

4.20 Image source selection................................................................................................................................................................31

4.21 Grayscale conversion modes...................................................................................................................................................32

4.22 DisplayPort standard version ...................................................................................................................................................32

4.23 EDID timings......................................................................................................................................................................................33

4.24 Display info .........................................................................................................................................................................................33

4.25 Display status....................................................................................................................................................................................33

4.26 SteadyColor™ ..................................................................................................................................................................................34

4.27 Maximum luminance demo .......................................................................................................................................................34

5 Cleaning your display........................................................................................................................................................................35

5.1 Cleaning instructions.....................................................................................................................................................................36

6 Repackaging instructions ..............................................................................................................................................................37

6.1 Repackaging instructions...........................................................................................................................................................38

7 Important information.........................................................................................................................................................................43

7.1 Safety information...........................................................................................................................................................................44

7.2 Environmental information.........................................................................................................................................................45

7.3 Regulatory compliance information ......................................................................................................................................47

7.4 EMC notice .........................................................................................................................................................................................48

7.5 Explanation of symbols................................................................................................................................................................51

7.6 Legal disclaimer...............................................................................................................................................................................54

7.7 Open source license information ...........................................................................................................................................54

7.8 Technical specifications...............................................................................................................................................................55

5R5911227 /04 Coronis Fusion 4MP / 6MP

Welcome! 1

R5911227 /04 Coronis Fusion 4MP / 6MP6

1.1 What's in the box

Overview

• Coronis Fusion 4MP / 6MP display

• User guide

• Documentation disc

• Video cables

• Mains cables

• USB cable

If you ordered a Barco display controller, it is also in the box together with its accessories. A dedicated user

guide is available on the documentation disc.

Keep your original packaging. It is designed for this display and is the ideal protection during

transport and storage.

1.2 Product overview

Front and Back

7

7 8

8

11 2

3

109

5

6

4

Image 1–1

1. SoftGlow Wall light

2. Ambient light sensor and Power status LED

- Off: Display not powered (mains cable unplugged or power switch in OFF position), or display is in

normal operation

- Fast blinking amber: Display is entering DPMS mode

- Slow blinking amber: Display is in DPMS mode

- Steady amber: Display manually switched off via the jog dial, or display in hibernate mode (requires

DPMS and Hibernate to be enabled in the OSD menu)

3. Front sensor

4. VESA mount cover

5. USB-A 2.0 downstream connector with high-power charging functionality

6. Connector compartment cover

Welcome!

7R5911227 /04 Coronis Fusion 4MP / 6MP

7. SoftGlow Task light

8. Jog dial

9. Cable routing channels

10.Stand locking mechanism

Connections

1 2 3 4 6 7 85

Image 1–2

1. Kensington security slot

2. Service port (for Barco service purposes only)

3. DisplayPort IN 2

4. DisplayPort OUT (covered with a plastic cap by default, remove the cap to use this connector)

5. DisplayPort IN 1

6. USB-A 2.0 downstream connectors (2x)

7. USB-B 2.0 upstream connector

8. 100–240 VAC mains power input and power switch

Welcome!

R5911227 /04 Coronis Fusion 4MP / 6MP8

Welcome!

9R5911227 /04 Coronis Fusion 4MP / 6MP

Installation 2

R5911227 /04 Coronis Fusion 4MP / 6MP10

2.1 Display controller installation

About

Before you install and connect your display with your workstation, make sure to have a suitable

1

display

controller installed in your workstation.

The Coronis Fusion 4MP / 6MP display operates at its full specifications when driven by a Barco

MXRT display controller and MXRT driver (which also includes the Barco Intuitive Workflow

Tools). If you ordered a MXRT display controller, it is included in the box of your display.

For more information and installation instructions, please check the Barco “Display Controller and

Intuitive Workflow Tools” user guide on the included documentation CD, or at

www.barco.com/support.

2.2 Display position adjustment

To adjust the display position

After unpacking, you can safely tilt and swivel the display to your preferred position.

Image 2–1

To adjust the height of the display, first move the slider at the back of the stand to the unlock position. Then

you can raise or lower the display as desired.

Installation

1. For a list of compatible display controllers, please refer to the compatibility matrix available on my.barco.com (MyBarco > My Support

> Healthcare > Compatibility Matrices > Barco Systems Compatibility Matrices)

11R5911227 /04 Coronis Fusion 4MP / 6MP

Image 2–2 Image 2–3

WARNING: The height can be locked only when the display is in the lowest position, even though

the slider at the back of the stand can be moved to the lock position at any height of the display.

2.3 Cable connections

To connect the cables

1. Open the connector compartment. Do this by gently lifting the bottom of the connector compartment cover,

after which it can be removed from the display.

Image 2–4

2. Connect the video source(s) from your workstation(s) to the DisplayPort IN connector(s) of the display.

Important: Do not connect any video source(s) to the DisplayPort OUT connector. Do not confuse this

connector with the DisplayPort IN 1 and 2 connectors.

Installation

R5911227 /04 Coronis Fusion 4MP / 6MP12

Note: The MDCC-4430, MDCC-6530 can have multiple video inputs connected at once, and switching

between these inputs can be easily done in the OSD menu. See “Image source selection”, page 31 for

more info on how to configure the different video inputs on your display.

3. The DisplayPort OUT allows you to daisy chain your display and an external display using DisplayPort

Multi-Stream Transport (MST).

Note: By default, the DisplayPort OUT is covered with a plastic cap which has to be removed before you

can use this connector.

4. Connect the workstation's USB host to the USB upstream connector on the display if you want to make

use of QAWeb or any of the display USB downstream connectors (e.g. to connect a keyboard, mouse,

touchpad or another peripheral).

Note: When cables or other objects are left on a touchpad, these can be misinterpreted as fingers and may

block DPMS activation. Barco recommends to always keep the touchpad clear of other objects.

5. Connect the supplied mains cable to the power input on the display.

2

3 4

4

2

5

DP IN 2

SERVICE

DP OUT DP IN 1

USB DOWN

USB UP

AC IN

Image 2–5

6. Route all cables through the cable duct in the stand of your display. For better strain-relief and shielding of

the cables, use the cable clips at the inside of the connector compartment.

7. Close the connector compartment. Slide the top of the connector compartment cover into position and then

push the bottom of the cover.

Note: Make sure that the power switch (next to the power input) is the desired position before closing the

connector compartment.

8. Connect the supplied mains cable to a grounded power outlet.

2.4 VESA-mount installation

CAUTION: Use suitable mounting apparatus to avoid risk of injury.

WARNING: Never move a display attached to an arm by pulling or pushing the display itself.

Instead, make sure that the arm is equipped with a VESA compliant handle and use this to move

the display.

Please refer to the instruction manual of the arm for more information and instructions.

WARNING: Use a mount that is compliant with the VESA 100 mm standard.

Use a mount that can support the weight of the display. Refer to the technical specifications of this

display for the applicable weight.

Installation

13R5911227 /04 Coronis Fusion 4MP / 6MP

Overview

The panel, standard attached to a stand, is compatible with the VESA 100 mm standard. Thus, it can be used

with an arm that is approved by VESA. This chapter shows you how to release the panel from the stand and

how to attach it to an arm. If you’re not using an arm, you can skip this chapter.

1. Unlock the stand locking mechanism and put the display in the highest position.

Image 2–6

2. Put the display face down on a clean and soft horizontal surface. Be careful not to damage the panel

screen.

3. Push the VESA mount cover to the right and lift the cover on the right with your finger or a flathead

screwdriver.

Image 2–7

4. Push the VESA mount cover to the left and release the cover on the left with a flathead screwdriver.

Image 2–8

Installation

R5911227 /04 Coronis Fusion 4MP / 6MP14

5. Rotate the VESA mount cover to uncover the screws fixing the panel to the stand.

Image 2–9

6. Unscrew the 4 fixation screws while supporting the stand.

Image 2–10

7. Attach the panel firmly to the arm using 4 M4 screws.

Respect the following rule to select an appropriate screw length:

- L

min

= T + W + 6.5 mm

- L

max

= T + W + 10 mm

T

W

L

min

L

max

Image 2–11

Installation

15R5911227 /04 Coronis Fusion 4MP / 6MP

2.5 MXRT driver and Intuitive Workflow Tools

installation

About

When you are using a Barco MXRT display controller, you can start up your Coronis Fusion 4MP / 6MP

display system and install the MXRT driver and Intuitive Workflow Tools . Barco’s Intuitive Workflow Tools

are designed to increase visibility of subtle details, improve focus during reading sessions, and accelerate

workflow.

To install the MXRT driver and Intuitive Workflow Tools

1. Switch on your Coronis Fusion 4MP / 6MP as described in “Standby switching”, page 19.

2. Turn on the workstation connected to your display.

Your display will be running in a basic video mode at a default refresh rate when first time starting up.

3. Download the latest MXRT driver and Intuitive Workflow Tools from www.barco.com/mxrt.

4. Install the MXRT driver and Barco’s Intuitive Workflow Tools as described in the Barco “Display

Controller and Intuitive Workflow Tools” user guide on the included documentation CD, or at

www.barco.com/support.

5. When the drivers are completely installed, your display will automatically detect the connected video input

signal(s) and apply the correct video mode and refresh rate.

2.6 QAWeb registration

About

QAWeb Enterprise helps you manage quality and assure compliance of your expanding healthcare

enterprise with less effort, lower cost, and complete confidence. This fully automated and secure system

guarantees a consistent image quality and uptime for all registered imaging display systems within your facility

and across your enterprise. Learn more at www.barco.com/qaweb.

To register your display system to your QAWeb Enterprise organization, the QAWeb Enterprise Agent must be

installed and running on your workstation and it must be able to communicate with the QAWeb Enterprise

cloud service.

For more information and instructions, check the QAWeb Enterprise user guide on

www.barco.com/support/qaweb-enterprise.

When still using the older MediCal QAWeb, visit www.barco.com/support/medical-qaweb to obtain

the installation package and user documentation.

Installation

R5911227 /04 Coronis Fusion 4MP / 6MP16

Installation

17R5911227 /04 Coronis Fusion 4MP / 6MP

Daily operation 3

R5911227 /04 Coronis Fusion 4MP / 6MP18

3.1 Recommendations for daily operation

Optimize the lifetime of your display

Enabling the Display Power Management System (DPMS) of your display will optimize its diagnostic lifetime

by automatically switching off the backlight when the display is not used for a specified period of time. By

default, DPMS is enabled on your display, but it also needs to be activated on your workstation. To do this, go

to the “Power Options” of your workstation.

Barco recommends setting DPMS activation after 20 minutes of non-usage.

Use a screen saver to avoid image retention

Prolonged operation of an LCD with the same content on the same screen area may result in a form of image

retention.

You can avoid or significantly reduce the occurrence of this phenomenon by using a screen saver. You can

activate a screen saver in the “Display properties” window of your workstation.

Barco recommends setting screen saver activation after 5 minutes of non-usage. A good screen

saver displays moving content.

In case you are working with the same image or an application with static image elements for several hours

continuously (so that the screen saver is not activated), change the image content regularly to avoid image

retention of the static elements.

Understand pixel technology

LCD displays use technology based on pixels. As a normal tolerance in the manufacturing of the LCD, a

limited number of these pixels may remain either dark or permanently lit, without affecting the diagnostic

performance of the product. To ensure optimal product quality, Barco applies strict selection criteria for its LCD

panels.

Enhance user comfort

Every Barco multi-head display system is color matched to the tightest specifications in the market.

Barco recommends keeping color-matched displays together. Furthermore, it is important to use all

displays of a multi-head configuration at the same rate to preserve color matching throughout the

economic lifetime of the system.

Maximize quality assurance

QAWeb Enterprise helps you manage quality and assure compliance of your expanding healthcare enterprise

with less effort, lower cost, and complete confidence. This fully automated and secure system guarantees a

consistent image quality and uptime for all registered PACS display systems within your facility and across

your enterprise.

Barco highly recommends to use QAWeb Enterprise. Learn more at www.barco.com/qaweb.

3.2 Shortcut bar

About the shortcut bar

The shortcut bar gives direct access to a number of OSD menu functions without having to browse the OSD

menu:

• “Standby switching”, page 19

• “SoftGlow light mode switching”, page 19

Daily operation

19R5911227 /04 Coronis Fusion 4MP / 6MP

• “OSD menu access and use”, page 20

Image 3–1

To activate a shortcut bar function

1. During normal operation, press or turn the jog dial. The shortcut bar is activated.

2. Turn the jog dial left or right to select a function.

3. Press the jog dial to confirm your selection and to activate the function.

3.3 Standby switching

To switch on your display

Make sure that the power switch at the back of your display is in the “I” position to use the display.

Press the jog dial to activate your display.

To switch off your display

1. Press or turn the jog dial to activate the shortcut bar.

2. Turn the jog dial and select the standby icon (

).

3. Press the jog dial to confirm your selection.

4. Press the jog dial again to switch off the display.

3.4 SoftGlow light mode switching

About the SoftGlow lights

The SoftGlow Task light sheds a light on the desktop, while the SoftGlow Wall light provides ambient lighting

for the reading room to reduce eye fatigue. The brightness of each is adjustable.

To switch the SoftGlow light mode

1. Press or turn the jog dial to activate the shortcut bar. The SoftGlow lights icon ( ) is selected by default

when the KVM switch is disabled.

2. If not selected by default, turn the jog dial and select the SoftGlow lights icon.

3. Press the jog dial repeatedly to cycle through the different SoftGlow light modes:

SoftGlow Task light ON → SoftGlow Wall light ON → SoftGlow Task + SoftGlow Wall light ON → SoftGlow

lights OFF→ ...

To adjust the brightness of the SoftGlow lights, please refer to “SoftGlow Task light”, page 23 and

“SoftGlow Wall light”, page 23.

The SoftGlow lights can also be enabled and configured in the Intuitive Workflow Tools. See the

Barco “Display Controller and Intuitive Workflow Tools” user guide on the included documentation

CD, or at www.barco.com/support.

Daily operation

R5911227 /04 Coronis Fusion 4MP / 6MP20

3.5 OSD menu access and use

About the OSD menu

The OSD menu allows you to configure different settings to make your Coronis Fusion 4MP / 6MP fit your

needs within your working environment. Also, you can retrieve general information about your display and its

current configuration settings through the OSD menu.

To access the OSD menu

1. Press or turn the jog dial to activate the shortcut bar.

2. Turn the jog dial and select the OSD menu icon (

).

3. Press the jog dial to enter the OSD menu.

4. If the OSD menu locked message appears, turn and hold the jog dial right for 5 seconds, until the OSD

menu unlocked message appears.

To navigate through the OSD menus

• Turn the jog dial left or right to scroll through the (sub)menus, to change values or to make selections.

• Press the jog dial to go into a submenu or confirm adjustments and selections.

• Press and hold the jog dial for approximately 3 seconds to cancel adjustments.

• Turn the jog dial left on a first (sub)menu item to exit the (sub)menu.

Daily operation

Page is loading ...

Barco Coronis Fusion 4MP (MDCC-4430) User guide

This manual is also suitable for

Barco Coronis Fusion 4MP (MDCC-4430) User guide

Related papers

Other documents