Vega Overvoltage protection B 62-30 W Operating instructions

Brand: Vega

Model: Overvoltage protection B 62-30 W

Type: Operating instructions

Vega Overvoltage protection B 62-30 W

The Vega Overvoltage protection B 62-30 W is an overvoltage arrester for supply and control cables for Profibus PA instruments. It protects against voltage surges caused by indirect atmospheric discharges (lightning strokes) or switching operations in the supply network. Further causes can be inductive or capacitive couplings from other electrical systems. Voltage peaks (transients) must be expected especially when long power supply and signal cables are used.

Here are some of the key features and possible use cases of the Vega Overvoltage protection B 62-30 W:

Vega Overvoltage protection B 62-30 W

Here are some of the key features and possible use cases of the Vega Overvoltage protection B 62-30 W:

Operating Instructions

Overvoltage arrester

B 62-30 W

For Probus PA and Foundation Fieldbus

circuits

Document ID: 40492

Contents

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

Contents

1 About this document

1.1 Function ........................................................................................................................... 3

1.2 Targetgroup ..................................................................................................................... 3

1.3 Symbolsused................................................................................................................... 3

2 For your safety

2.1 Authorisedpersonnel ....................................................................................................... 4

2.2 Appropriateuse ................................................................................................................ 4

2.3 Warningaboutincorrectuse ............................................................................................. 4

2.4 Generalsafetyinstructions ............................................................................................... 4

2.5 Safetylabelontheinstrument .......................................................................................... 5

2.6 EUconformity ................................................................................................................... 5

2.7 Environmentalinstructions ............................................................................................... 5

3 Product description

3.1 Conguration .................................................................................................................... 6

3.2 Principleofoperation........................................................................................................ 6

3.3 Packaging,transportandstorage ..................................................................................... 7

4 Mounting instructions

4.1 Installationinswitchingcabinet ........................................................................................ 9

4.2 Mountinginhousing ....................................................................................................... 10

5 Connecting to power supply

5.1 Preparingtheconnection ............................................................................................... 12

5.2 Connectionstepsforversionwithhousing ..................................................................... 12

5.3 Wiringplan ..................................................................................................................... 12

6 Maintenanceandfaultrectication

6.1 Maintenance .................................................................................................................. 14

6.2 Rectifyfaults ................................................................................................................... 14

6.3 Howtoproceedifarepairisnecessary .......................................................................... 14

7 Dismount

7.1 Dismountingsteps.......................................................................................................... 15

7.2 Disposal ......................................................................................................................... 15

8 Supplement

8.1 Technicaldata ................................................................................................................ 16

8.2 DimensionsB62-30W .................................................................................................... 17

Safety instructions for Ex areas

TakenoteoftheExspecicsafetyinstructionsforExapplications.

Theseinstructionsareattachedasdocumentstoeachinstrument

withExapprovalandarepartoftheoperatinginstructionsmanual.

Editingstatus:2017-04-28

1Aboutthisdocument

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

1 About this document

1.1 Function

Thisoperatinginstructionsmanualprovidesalltheinformationyou

needformounting,connectionandsetupoftheinstrument.Further-

morethereareimportantinstructionsformaintenance,faultrectica-

tion,theexchangeofpartsandthesafetyoftheuser.Pleasereadthis

informationbeforeputtingtheinstrumentintooperationandkeepthis

manualaccessibleintheimmediatevicinityofthedevice.

1.2 Target group

Thisoperatinginstructionsmanualisdirectedtotrainedspecialist

personnel.Thecontentsofthismanualshouldbemadeavailableto

thesepersonnelandputintopracticebythem.

1.3 Symbols used

Information, tip, note

Thissymbolindicateshelpfuladditionalinformation.

Caution:Ifthiswarningisignored,faultsormalfunctionscanresult.

Warning:Ifthiswarningisignored,injurytopersonsand/orserious

damagetotheinstrumentcanresult.

Danger:Ifthiswarningisignored,seriousinjurytopersonsand/or

destructionoftheinstrumentcanresult.

Ex applications

ThissymbolindicatesspecialinstructionsforExapplications.

SIL applications

Thissymbolindicatesinstructionsforfunctionalsafetywhichmustbe

takenintoaccountparticularlyforsafety-relevantapplications.

•

List

Thedotsetinfrontindicatesalistwithnoimpliedsequence.

→

Action

Thisarrowindicatesasingleaction.

1 Sequence of actions

Numberssetinfrontindicatesuccessivestepsinaprocedure.

Battery disposal

Thissymbolindicatesspecialinformationaboutthedisposalofbat-

teriesandaccumulators.

2Foryoursafety

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

2 For your safety

2.1 Authorised personnel

Alloperationsdescribedinthisoperatinginstructionsmanualmust

becarriedoutonlybytrainedspecialistpersonnelauthorisedbythe

plantoperator.

Duringworkonandwiththedevicetherequiredpersonalprotective

equipmentmustalwaysbeworn.

2.2 Appropriate use

TheB62-30Wisanovervoltagearresterforsupplyandcontrolcables

forProbusPAinstruments.

Youcannddetailedinformationabouttheareaofapplicationin

chapter"Product description".

2.3 Warning about incorrect use

Inappropriateorincorrectuseoftheinstrumentcangiveriseto

application-specichazards,e.g.vesseloverllordamagetosystem

componentsthroughincorrectmountingoradjustment.Thusdam-

agetoproperty,topersonsorenvironmentalcontaminationcanbe

caused.Alsotheprotectivecharacteristicsoftheinstrumentcanbe

inuenced.

2.4 General safety instructions

Thisisastate-of-the-artinstrumentcomplyingwithallprevailing

regulationsanddirectives.Theinstrumentmustonlybeoperatedina

technicallyawlessandreliablecondition.Theoperatorisresponsi-

bleforthetrouble-freeoperationoftheinstrument.Whenmeasuring

aggressiveorcorrosivemediawhereamalfunctionoftheinstrument

cancauseadanger,theoperatorhastoconvincehimselfonthecor-

rectfunctionoftheinstrumentbytakingsuitablemeasures.

Duringtheentiredurationofuse,theuserisobligedtodeterminethe

complianceofthenecessaryoccupationalsafetymeasureswiththe

currentvalidrulesandregulationsandalsotakenoteofnewregula-

tions.

Thesafetyinstructionsinthisoperatinginstructionsmanual,thena-

tionalinstallationstandardsaswellasthevalidsafetyregulationsand

accidentpreventionrulesmustbeobservedbytheuser.

Forsafetyandwarrantyreasons,anyinvasiveworkonthedevice

beyondthatdescribedintheoperatinginstructionsmanualmaybe

carriedoutonlybypersonnelauthorisedbythemanufacturer.Arbi-

traryconversionsormodicationsareexplicitlyforbidden.Forsafety

reasons,onlytheaccessoryspeciedbythemanufacturermustbe

used.

Toavoidanydanger,thesafetyapprovalmarkingsandsafetytipson

thedevicemustalsobeobservedandtheirmeaninglookedupinthis

operatinginstructionsmanual.

2Foryoursafety

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

2.5 Safety label on the instrument

Thesafetyapprovalmarkingsandsafetytipsonthedevicemustbe

observed.

2.6 EU conformity

ThedevicefullsthelegalrequirementsoftheapplicableEUdirec-

tives.ByaxingtheCEmarking,weconrmsuccessfultestingofthe

product.

YoucanndtheCECerticateofConformityinthedownloadsection

under"www.vega.com".

2.7 Environmental instructions

Protectionoftheenvironmentisoneofourmostimportantduties.

Thatiswhywehaveintroducedanenvironmentmanagementsystem

withthegoalofcontinuouslyimprovingcompanyenvironmentalpro-

tection.Theenvironmentmanagementsystemiscertiedaccording

to DIN EN ISO 14001.

Pleasehelpusfullthisobligationbyobservingtheenvironmental

instructionsinthismanual:

•

Chapter"Packaging, transport and storage"

•

Chapter"Disposal"

3Productdescription

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

3 Product description

3.1 Conguration

Thescopeofdeliveryencompasses:

•

OvervoltagearresterB62-30W

•

Documentation

– Thisoperatinginstructionsmanual

– Exspecicsafetyinstructionsand,ifnecessary,furthercerti-

cates

Thefollowingillustrationshowsthecongurationoftheovervoltage

arresterB62-30W:

B62 - 30 W

OUT

IP 20

max. 36 VDC/ li 0,4 A

Ri = 3,6 Ohm

A1+

A2-

E1+

E2-

Fig. 1: Conguration of B62-30W

1 Terminals Out (protected side)

2 Screw for carrier rail fastening

3 Terminals In (unprotected side)

4 Type label

3.2 Principle of operation

Voltagesurgescanbecausedbyindirectatmosphericdischarges

(lightningstrokes)orswitchingoperationsinthesupplynetwork.

Furthercausescanbeinductiveorcapacitivecouplingsfromother

electricalsystems.Voltagepeaks(transients)mustbeexpectedespe-

ciallywhenlongpowersupplyandsignalcablesareused.

Scope of delivery

Constituent parts

Application area

3Productdescription

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

Suchvoltagesurgescancausedamagetosensorsandsignalcondi-

tioninginstruments.

VEGAovervoltagearrestersreducevoltagesurgesonthesupplyor

signalcablestoasafelevel.Theyaredesignedformountingoncar-

rierrailaccordingtoEN50022/EN50035intheswitchingcabinetor

inametalorplastichousingclosetothesensor.

Dependingontheversion,dierentcombinationsofprotectiveele-

mentsforvoltagelimitationareused.Typicalprotectiveelements

aresuppressordiodes(diodeswithspecialcharacterstics),varistors

(voltage-dependentresistors)aswellasovervoltagearresters(gas

arresters).

Assoonasthevoltageincreasestotheresponsevoltageofthe

protectiveelement,theelementbecomesconductiveandtheenergy

isdischargedtoground.Aftertheovervoltagehassubsided,the

protectiveelementreturnstoitshigh-impedancestateandthushas

noinuenceonthesupplyorsignalcircuit.

3.3 Packaging, transport and storage

Yourinstrumentwasprotectedbypackagingduringtransport.Its

capacitytohandlenormalloadsduringtransportisassuredbyatest

basedonISO4180.

Thepackagingofstandardinstrumentsconsistsofenvironment-

friendly,recyclablecardboard.Forspecialversions,PEfoamorPE

foilisalsoused.Disposeofthepackagingmaterialviaspecialised

recyclingcompanies.

Transportmustbecarriedoutindueconsiderationofthenotesonthe

transportpackaging.Nonobservanceoftheseinstructionscancause

damagetothedevice.

Thedeliverymustbecheckedforcompletenessandpossibletransit

damageimmediatelyatreceipt.Ascertainedtransitdamageorcon-

cealeddefectsmustbeappropriatelydealtwith.

Uptothetimeofinstallation,thepackagesmustbeleftclosedand

storedaccordingtotheorientationandstoragemarkingsonthe

outside.

Unlessotherwiseindicated,thepackagesmustbestoredonlyunder

thefollowingconditions:

•

Notintheopen

•

Dryanddustfree

•

Notexposedtocorrosivemedia

•

Protectedagainstsolarradiation

•

Avoidingmechanicalshockandvibration

•

Storageandtransporttemperatureseechapter"Supplement -

Technical data - Ambient conditions"

•

Relativehumidity20…85%

Functional principle

Packaging

Transport

Transport inspection

Storage

Storage and transport

temperature

3Productdescription

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

Withaninstrumentweightofmorethan18kg(39.68lbs)suitableand

approvedequipmentmustbeusedforliftingandcarrying.

Lifting and carrying

4Mountinginstructions

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

4 Mounting instructions

4.1 Installation in switching cabinet

Theovervoltagearresterismountedintheswitchingcabineton

carrierrailsaccordingtoEN50022(DINrail)orEN50035(C-rail).It

isfastenedtothecarrierrailwithascrewlocatedonitsexterior.The

screwismarkedwiththesymbolforfunctionalground.Dependingon

theversion,itmaybegalvanicallyconnectedtothegroundterminalof

theovervoltagearrester(seecircuitdiagraminchapter"Wiring plan").

Thecarrierrailmustbeconnected(lowimpedance)tothepotential

equalizationline(PA).Thewirecross-sectionmustbeatleast2.5

,thecablemustbeasshortaspossible.

Fig. 2: Mounting on carrier rail according to EN 50 022 (DIN rail) 35 x 7.5 mm

1 Carrier rail

Fig. 3: Mounting on carrier rail according to EN 50 035 (C-rail) 35 x 7.5 mm

1 Carrier rail

Installation procedure

Proceedasfollows:

1. Loosenxingscrew

4Mountinginstructions

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

OUT

IP 20

Fig. 4: Mounting on carrier rail

1 Fixing screw

2. Placetheovervoltagearresterontotherailandletitsnapin

3. Tightenxingscrew

4.2 Mounting in housing

Theovervoltagearresterisoptionallyavailableinaplasticoralu-

miniumhousing.Makesurewhenmountingthatthecableglands

pointdownward.Thusavoidswateringress.

OUT

IP 20

Fig. 5: Mounting in Aluminium housing

1 Overvoltage arrester

2 Pressure compensation

3 Ground terminal

4Mountinginstructions

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

OUT

IP 20

Fig. 6: Mounting in plastic housing

1 Overvoltage arrester

2 Pressure compensation

3 Ground terminal

Thecarrierrailinsidethehousingisgalvanicallyconnectedtothe

groundterminaloutsideonthehousing.Thisgroundterminalmustbe

connected(lowimpedance)withthepotentialequalizationline(PA).

Thewirecross-sectionmustbeatleast2.5mm

,thecablemustbe

asshortaspossible.

5Connectingtopowersupply

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

5 Connecting to power supply

5.1 Preparing the connection

Alwayskeepinmindthefollowingsafetyinstructions:

•

Connectonlyinthecompleteabsenceoflinevoltage

Beforestartingsetupmakesurethatthepowersupplycorrespondsto

thespecicationsonthetypelabel.

Foreectiveovervoltageprotection,thecablesbetweenovervoltage

arresterandinstrumentshouldbeasshortaspossible.

5.2 Connection steps for version with housing

Proceedasfollows:

1. Loosenscrewsofthehousingcover

2. Pushthesupplyandconnectioncablesthroughthecablegland

intothehousing,stripapprox.1cm(0.4in)insulationfromthe

endsofthewires

3. Connectthewireendsaccordingtochapter"Wiring plan"tothe

terminalsoftheovervoltagearrester

4. Connecttheoutergroundterminalonthehousingtopotential

equalization

5. Checkallcableconnections,especiallythegroundconnection,to

makesuretheyaretightenedsuciently

6. Tightenthecompressionnutsofthecableglands.Thesealring

mustcompletelyencirclethecable

7. Tightenscrewsofthehousingcover

Theelectricalconnectionisnished.

5.3 Wiring plan

Fig. 7: Circuit diagram B62-30W

1 Circuit diagram overvoltage arrester B62-30W

2 Potential equalisation

Note safety instructions

Circuit diagram

5Connectingtopowersupply

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

2 -

B62 - 30 W

OUT

IP 20

max. 36 VDC/ li 0,4 A

Ri = 3,6 Ohm

A1+

A2-

E1+

E2-

Fig. 8: Wiring plan B62-30W - Sensor protection

1 Sensor

2 Overvoltage arrester for sensor

3 Probus PA System

4 Potential equalisation

2 -

B62 - 30 W

OUT

IP 20

max. 36 VDC/ li 0,4 A

Ri = 3,6 Ohm

A1+

A2-

E1+

E2-

Fig. 9: Wiring plan B62-30W - Protection for bus system

1 Sensor

2 Overvoltage arrester for bus system

3 Probus PA System

4 Potential equalisation

Wiring plan - Sensor

protection

Wiring plan - Protection

for bus system

6Maintenanceandfaultrectication

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

6 Maintenanceandfaultrectication

6.1 Maintenance

Ifthedeviceisusedproperly,nospecialmaintenanceisrequiredin

normaloperation.

6.2 Rectify faults

Theoperatorofthesystemisresponsiblefortakingsuitablemeas-

urestorectifyfaults.

Therstmeasuretobetakenistochecktheinput/outputsignalas

wellasthepowersupply.Inmanycases,thecausescanbedeter-

minedandfaultscanbequicklyrectied.

On-siterepairofB62-30Wisnotpossible.

Shouldthesemeasuresnotbesuccessful,pleasecallinurgentcases

theVEGAservicehotlineunderthephoneno.+49 1805 858550.

Thehotlineismanned7daysaweekround-the-clock.Sinceweoer

thisserviceworldwide,thesupportisonlyavailableintheEnglish

language.Theserviceisfree,onlystandardcallchargesareincurred.

Dependingonthereasonforthefaultandthemeasurestaken,the

stepsdescribedinchapter"Set up"mayhavetobecarriedoutagain.

6.3 How to proceed if a repair is necessary

Youcanndaninstrumentreturnformaswellasdetailedinforma-

tionabouttheprocedureinthedownloadareaofourhomepage:

www.vega.com.

Bydoingthisyouhelpuscarryouttherepairquicklyandwithouthav-

ingtocallbackforneededinformation.

Ifarepairisnecessary,pleaseproceedasfollows:

•

Printandlloutoneformperinstrument

•

Cleantheinstrumentandpackitdamage-proof

•

Attachthecompletedformand,ifneedbe,alsoasafetydata

sheetoutsideonthepackaging

•

Pleasecontacttheagencyservingyoutogettheaddressfor

thereturnshipment.Youcanndtheagencyonourhomepage

www.vega.com.

Reaction when malfunc-

tion occurs

Faultrectication

24 hour service hotline

Reaction after fault recti-

cation

7Dismount

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

7 Dismount

7.1 Dismounting steps

Takenoteofchapters"Mounting"and"Connecting to power supply"

andcarryoutthelistedstepsinreverseorder.

7.2 Disposal

Theinstrumentconsistsofmaterialswhichcanberecycledbyspe-

cialisedrecyclingcompanies.Weuserecyclablematerialsandhave

designedtheelectronicstobeeasilyseparable.

WEEE directive 2002/96/EG

ThisinstrumentisnotsubjecttotheWEEEdirective2002/96/EGand

therespectivenationallaws.Passtheinstrumentdirectlyontoaspe-

cialisedrecyclingcompanyanddonotusethemunicipalcollecting

points.Thesemaybeusedonlyforprivatelyusedproductsaccording

totheWEEEdirective.

Correctdisposalavoidsnegativeeectsonhumansandtheenviron-

mentandensuresrecyclingofusefulrawmaterials.

Materials:seechapter"Technical data"

Ifyouhavenowaytodisposeoftheoldinstrumentproperly,please

contactusconcerningreturnanddisposal.

8Supplement

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

8 Supplement

8.1 Technical data

Note for approved instruments

Thetechnicaldataintherespectivesafetyinstructionsarevalidforapprovedinstruments(e.g.with

Exapproval).Thesedatacandierfromthedatalistedherein,forexampleregardingtheprocess

conditionsorthevoltagesupply.

General data

Version

Deviceforcarrierrailmounting

Housingmaterial Plastic(PPE)

Weightapprox. 175g(0.385lbs)

Electrical characteristics

Operatingvoltage 9…36VDC

Max.permissiblecurrentpercircuit 0.6A

percircuit ≤3.6Ω

percircuit 0 mH

percircuit 0 nF

Responsevoltage 41 V DC

Responsetime < 10

-11

Dischargecurrent <10kA(8/20µs)

Electromechanical data

Screwterminalsforcablecross-section <2.5mm²(AWG14)

Ambient conditions

Ambienttemperature -40…+60°C(-40…+140°F)

Storageandtransporttemperature -40…+70°C(-40…+158°F)

Electrical protective measures

Protectionrating

Ʋ unassembled IP 20

Ʋ InAluminiumorplastichousing IP 65

 Referencetemperature25°C(77°F).

8Supplement

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

8.2 Dimensions B62-30W

Overvoltage arrester

84 mm

(3.31")

52 mm

(2.05")

25 mm

(0.98")

Fig. 10: Dimensions B62-30W

8Supplement

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

Housing

ø5,5 mm

(0.22")

86 mm

(3.39")

120 mm

(4.72")

160 mm

(6.30")

77 mm

(3.03")

47 mm

(1.85")

50 mm

(1.97")

ø4,5 mm

(0.18")

82 mm

(3.23")

68 mm

(2.68")

72 mm

(2.84")

130 mm

(5.12")

116 mm

(4.57")

M 20 x 1,5

Fig. 11: Dimensions B62-30W

1 Plastic housing

2 Aluminium housing

Notes

B62-30W•ForProbusPAandFoundationFieldbuscircuits

40492-EN-170510

Printing date:

VEGA Grieshaber KG

Am Hohenstein 113

77761 Schiltach

Germany

40492-EN-170510

All statements concerning scope of delivery, application, practical use and operat-

ing conditions of the sensors and processing systems correspond to the information

available at the time of printing.

Subject to change without prior notice

Phone +49 7836 50-0

Fax +49 7836 50-201

E-mail: [email protected]

www.vega.com

Vega Overvoltage protection B 62-30 W Operating instructions

Brand: Vega

Model: Overvoltage protection B 62-30 W

Type: Operating instructions

Vega Overvoltage protection B 62-30 W

Here are some of the key features and possible use cases of the Vega Overvoltage protection B 62-30 W:

Download PDF

report

Vega Overvoltage protection B 62-30 W Operating instructions

Vega Overvoltage protection B 62-30 W Operating instructions

Related papers

Other documents