Barco RGBHV input board (QXGA) for iCon Installation guide

Brand: Barco

Model: RGBHV input board (QXGA) for iCon

Category: Projectors

Type: Installation guide

This manual is also suitable for

RGBHV input board QXGA for iCon

RGB/video input kit

Installation Manual

iCon H600, NH-12, Galaxy NH-12, XDS-100

R9843020

R5976888/02

25/11/2010

Barco nv Presentations

Noordlaan 5, 8520 Kuurne

Phone: +32 56.36.82.11

Fax: +32 56.35.86.51

E-mail: pre[email protected]

Visit us at the web: www.barco.com

Printed in Belgium

Disposal Information

This equipment has required the extraction and use of natural resources for its production. It may contain hazardous substances for health

and environme nt. In order to avoid the dissemination of those substances in the environment and to diminish the pressure on natural

resources, we encourage you to use the appropriate take-back systems. Those systems will reuse or recycle most of the materials of your

end of life equipment in a sound way.

The crossed-out wheeled bin sym bol invites you to use those s ystems. If you need more information on the collection, reuse and recycling

systems, please contact your local or r egional waste administrator. You can also contact us for m ore information on the environmental

performances of our products.

Federal Communications Commission (FCC Statement)

This equipment h as been tested and found to c omply with the limits for a class A digital device, pursuant to Par t 15 of the F CC rules.

These limits are designed to prov ide reasonable protection against harmful interference when the equipment is operated in a com mercial

environment. This eq u ipment generates, uses, and can radiate radio frequency ener gy and, if not installed and used in a ccordance with

the instruction m anual, may c ause harmful interference to radio communications. O peration of this equipment in a residential area may

cause harmful interference, in which case the us er will b e responsible for correcting any interference at his own expense

EN55022/CISPR22 Cla ss A ITE (Information Technology Equipment)

Class A ITE is a category of all other ITE which satisﬁes the class A ITE limits b ut not the class B ITE limits. Such equipment should not

be res tricted in its sale but the following warning shall b e included in the instructions for use:

Warning : This is a class A product. In a dom estic environment this product m ay cause radio interference in which case the user may be

required to take adequate meas ures.

stored in a retrieval system without the prior written conse

nt of Barco.

Changes

Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied w ar-

ranties or m erchantability and ﬁtness for a particular pur pose. Barco m ay make improvements and/or changes to the product(s) and/or the

program(s) described in this publication at any time without notice.

This pub lication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this

publication; these c hanges are incorporated in new editions of this publication.

Guaran tee and Compensation

Barco provides a guarantee relating to perfect man ufacturing as part of the legally stipulated terms of guar antee. O n receipt, the purchaser

must im mediately inspect a ll delivered goods for dam age incurred during transport, a s well as for material and manufacturing faults Barco

must be informed immediately in writing of any complaints.

The pe riod of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of c omm issioning,

at latest 30 days after the transfer of risks. In the ev ent of justiﬁed notice of complaint, Bar co can repair the fault or p rovide a replacement

at its own discretion w ithin an appropri

ate period. If this measure proves to be impos sible or uns uccessful, the purchaser can deman d a

reduction in the purchase price or c ancellation of the contract. All other claim s, in particular those relating to com pensa tion for direct or

indirect damage, and also da mage attributed to the operation of software as well as to other services provided by Barco, b eing a com ponent

of the system or independent servic

e, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties

guaranteed in writing or due to the intent or gross negligence or part of Bar co.

If the purchaser or a third party carries out m odiﬁcations or repairs on go ods delivered by B arco, or if the goods are handled incorrectly,

in particular if the systems a re commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to inﬂ uenc es not

agreed upon in the contract, all guarantee claims of the purchaser will be r endered invalid. Not included in the guarantee cove rage a re

system failures w hich are attributed to programs or special electronic circuitry pr ovided by the purchaser, e.g. interfaces. Nor mal wear as

well as normal maintenance are not subjec t to the guarantee provided by Bar co either.

The environmental conditions as well as the servicing and maintenance regulations speciﬁed in the this manual m ust be complied with by

the customer.

Table of contents

TABLE OF CON TENTS

1. Safety................................................................................................................. 3

1.1 Safety warnings....................................................................................................................... 3

2. Kit description ...................................................................................................... 5

2.1 Description............................................................................................................................ 5

2.2 kit contents............................................................................................................................ 5

3. (Re)placing the RGB input on iCon H600 .... .......... .......... .... ...... .... ...... .... .......... .......... .. 7

3.1 Accessing the input section .......................................................................................................... 7

3.1.1 Removing the lens cover ...................................................................................................... 7

3.1.2 Removing the installed lens ...................................................................................................7

3.1.3 Removing the rear cover ...................................................................................................... 8

3.1.4 Removing the top cover ....................................................................................................... 8

3.1.5 Removing the ﬁlter front plate ................................................................................................10

3.1.6 Removing the front plate......................................................................................................10

3.1.7 Removing the Server .........................................................................................................12

3.2 (Re)placing the RGB input ..........................................................................................................17

4. Installing the RGB/video input on NH-12 and Galaxy NH-12 . .... .... .... ............. ......... .... .... ... 21

4.1 Assembling the RGB/video input board . . . . ........................................................................................21

4.2 Removing the rear cover............................................................................................................21

4.3 Removing the top cover.............................................................................................................22

4.4 Installation of the RGB/video input board...........................................................................................23

4.5 Installing the top cover ..............................................................................................................25

4.6 Installing the rear cover .............................................................................................................26

5. Installing the RGB/video input on XDS-100... ......... .... .... .... .... .... .... ............. ......... .... .... .29

5.1 Procedure to install the RGB /video input board . ...................................................................................29

Index......................................................................................................................33

R5976888 RGB/VIDEO INPUT KIT 25/11/2010 1

Table of contents

2 R5976888 RGB/VIDEO INPUT KIT 25/11/2010

1. Safety

1. SAFETY

1.1 Safety warnings

WARNING: This procedure is intended for use only by BARCO authorized technicians.

WARNING: Be sure that the device is powered down and that the power co rd is rem oved from the wall o utlet.

Wait until the device is cooled down before starting the procedure.

CAUTION: Wear a w rist band w hich is connected to the ground while handling the electrostatic discharge

sensitive parts.

R5976888 RGB/VIDEO INPUT KIT 25/11/2010 3

1. Safety

4 R5976888 RGB/VIDEO INPUT KIT 25/11/2010

2. Kit description

2. KIT DESCRIPTION

2.1 Description

Purpose

The RGB/Video input board allows to co nnect the following sources to the device:

• 1 RG B (analog) input on 5 BNC c onnectors

• 1 com posite v ideo on a BNC connector

• 1 S-Video input on a mini-DIN connector

The ﬂexibility of the device’s input section allows to add this input on one of the input slots.

The input is automatically detected and the co nﬁguration of the input parameters is done at ﬁrst startup.

2.2 kit contents

Overview

Part description

Qty

Image

RGB/video input board

1 image 2-3

Fitting ring 1

Front screw 4 image 2-1

Fixation nut 1 image 2-2

Side screw

2 image 2-1

Bottom screw 1

Front plate for iCon H600

1 image 2-4

Front plate for NH-12 / G alaxy NH-12 1 image 2-5

Image 2-1

Screw

Image 2-2

Fixation nut

Image 2-3

R5976888 RGB/VIDEO INPUT KIT 25/11/2010 5

2. Kit description

Image 2-4

Image 2 -5

6 R5976888 RGB/VIDEO INPUT KIT 25/11/2010

3. (Re)placing the RGB input on iCon H600

3. (RE)PLACING THE RGB INPU T ON ICON H600

Upgrade/replacement

The following procedure illustrates t he replacem ent of an RGB input board. The sam e operations mus t be done in case one wants

to add a third RG B input to the projector. Instead of removing (the defective) RGB board one has then to remove the board installed

on the desired lay er.

Layer 5 is used for the DVI output and can not be used to install an input board.

Layer 4 is free and can be used to install an extra input.

3.1 Accessing the input section

Overview

• Removing the lens cover

• Removing the installed lens

• Removing the rear cover

• Removing the top cover

• Removing the ﬁlter front plat e

• Removing the front plate

• Removing the S erve r

3.1.1 Removing the lens cover

Necessary tools

cross headed screwdriver

How to remove the lens cover ?

1. L oosen the 2 indicated screws.

Image 3-1

2. O pen the protective cloth (enlarge the opening) and pull the lens cover gently from the front of the projector.

3.1.2 Removing the installed lens

How to remove the installed lens ?

1. Disconnect the lens from the m otor connec

tion bo ard

2. S upport the lens with one hand.

R5976888 RGB/VIDEO INPUT KIT 25/11/2010

3. (Re)placing the RGB input on iCon H600

Image 3 -2

Image 3-3

Detail of the lens locking handle and pin

3. P ull out the locking pin and ﬂip the lens loc king handle to the r ight (with the index ﬁnger) at the same time.

4. P ull the lens gently out of the lens holder.

3.1.3 Removing the rear cover

Necessary tools

cross headed screwdriver.

How to remove the rear cover ?

1. Loosen and re move the 2 screws as indicated.

Image 3-4

2. Remove the rear cover

3.1.4 Removing t he top cover

Necessary tools

cross headed screwdriver.

How to remove the top cover ?

1. L oosen and rem ove the 2 rear screws

R5976888 RGB/VIDEO INPUT KIT 25/11/2010

3. (Re)placing the RGB input on iCon H600

Image 3-5

2. L oosen and rem ove the 2 front screws

Image 3-6

3. Loosen and remove the indicated screw

Image 3-7

4. Remove the top cover and disconnect the local keypad connector.

R5976888 RGB/VIDEO INPUT KIT 25/11/2010

3. (Re)placing the RGB input on iCon H600

Image 3-8

3.1.5 Removing the ﬁlter front plate

Necessary tools

Torx n°10

How to remove the ﬁlter front plate

1. Remove the 4 screws ﬁxing the ﬁlter front plate

Image 3-9

2. Remove the plate

Image 3-10

Note: The pla te is ﬁxed in 3 holes

3.1.6 Removing the front plate

Necessary tools

•Torxn°10

• nut s pinner n°5

How to remove the front pla te ?

1. Remove the 4 screws

R5976888 RGB/VIDEO INPUT KIT 25/11/2010

3. (Re)placing the RGB input on iCon H600

Image 3-11

2. Remove the 4 screws ﬁxing the V GA and the RS 232 connector

Image 3-12

3. Remove the 2 screws ﬁxing the USB connec tors.

Note: the2screwsareﬁxed with 2 nuts on the rear of the plate : remove gently the plate forwards to access the nuts.

Image 3-13

Tip: In case one m ust only access the side screws on the P MP it is no t necessary to loos en the USB connector.

4. Remove the plate or ﬂip it to the side in c ase the USB connector has not be en removed.

R5976888 RGB/VIDEO INPUT KIT 25/11/2010 11

3. (Re)placing the RGB input on iCon H600

Image 3-14

Flip front plate in case it m ust not be removed (USB connection not removed)

When an Audio or other extension module is used on the extra PCI slot, the 2 screws ﬁxing this module should

also be remo ved.

3.1.7 Removing the Server

What has to be done ?

Depending on the type o f plate 1 piece/2pieces) the removal pro

cedure is slightly different :

R5976888 RGB/VIDEO INPUT KIT 25/11/2010

3. (Re)placing the RGB input on iCon H600

1. 1 piece plate : the plate must be removed

Image 3-15

1 piece plate

2. 2 piece plate : remove only the side plate (1) , the server can be slided to the side.

Image 3-16

2 piece plate

1sideplate

2 top plate

How to remove the server ?

1. Remove the HDD adapter from the HD

Image 3-17

2. If the plate is in one piece

If yes, rem o ve the 4 scre w s

If no, go to step 8

R5976888 RGB/VIDEO INPUT KIT 25/11/2010

3. (Re)placing the RGB input on iCon H600

Image 3-18

3. P ush the ﬂat cable and the power ca ble through the hole.

Image 3-19

Flat cable and power cable (arrows) and cable bundle

4. Remove the wire bundle from cable protection lock.

5. Remove the 6 screws ﬁxing the metallic protection cover.

Image 3-20

6. Remove the second wire bundle from the lower cable protective lock.

R5976888 RGB/VIDEO INPUT KIT 25/11/2010

3. (Re)placing the RGB input on iCon H600

Image 3-21

7. 1 piece plate : Remov e the indicated screws to allow the server to be slided to the side.

Image 3 -22

Image 3 -23

8. Remove t he LVDS co nnections from the PMP (only in case the server must be com pletely removed).

R5976888 RGB/VIDEO INPUT KIT 25/11/2010

3. (Re)placing the RGB input on iCon H600

Image 3-24

9. Remove the ATX power cable from the pow er box (only in case the se rver mus t b e completely removed).

Image 3-25

10.R emov e the E thernet connection and the small connector from the PMP (only if server mus t be completely removed).

Tip: The small cable is connected o n the back of the PMP, access to the con nector is m ade easy by removing the connector

in front of it (only if server must be com pletely removed).

Image 3-26

11.Remove the 3 screws ﬁxing the server to the projector frame.

R5976888 RGB/VIDEO INPUT KIT 25/11/2010

Page is loading ...

Barco RGBHV input board (QXGA) for iCon Installation guide

Brand: Barco

Model: RGBHV input board (QXGA) for iCon

Category: Projectors

Type: Installation guide

This manual is also suitable for

RGBHV input board QXGA for iCon

Download PDF

report

Barco RGBHV input board (QXGA) for iCon Installation guide

This manual is also suitable for

Barco RGBHV input board (QXGA) for iCon Installation guide

Related papers

Other documents