2. Barco
  3. iCon H600
iCon H600

Barco iCon H600 Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the Barco iCon H600 Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Barco service bulletin
Serial Number: InfoT 699
Date: 15/03/2007
Product: Barco iCon H600
Priority code*: D
A.
”Must” modification, Barco will provide t he necessary components to per form this mo difica tion
at no charge.
B.
Improves the reliability of the product.
C.
Improves the general working conditions of the product.
D.
For information only.
1. SOFTWARE V1.30
1.1 Specifications
CAUTION: This upgrade to V1.30 may only be done on projectors running
software V1.26.
Do not upgrade a projector
that runs a software version older than V1.26
(< V1.26) !
If the projector uses a software version older than V1.26, first upgrade
to V1.26 !
Firmware
• Scaling : issue preve
nting some portrait mode sources to be shown is solved.
• Image files : rename/copy of an empty list problem s solved.
Problem with the editing of YUV sources is solved.
Reduced number of image files for new projectors : 33 older image files are no longer
supported by the file system (see table below), and 2 portrait UXGA files added (UX-
GAP2@60, UXGAP1@59).
Note that the removed files will not be present on new pr ojectors but remain available
on old and upgraded projectors (since upgrading does not remove existing files).
• Power down : Locking state a t projector shutdown. In case the server does not respond
to an initiation of th
e shutdown process, the server is automatica lly put into shutdown
mode after 5 m i nutes waiting t ime. A countdown starts after 2 minut es and is shown in
therightbottomsideofthemessagedialogbox.
Barco nv Simulation Products
Noordlaan 5,
B-8520 Kuurne
www.barco.com
Page 1 of 4
Barco service bulletin
Server
• Only in VR Workroom : Start pixels settings can be set separately for stereo s ources
(for left and right ch ann el). For more de tails, See the VR Workroom Installation manual
R5976989_01
Note : This setting is not sho wn when the source is in mon o !
• Only in VR Workroom : Mono in VR Workroom mode : sometimes the selected projector
didnotstartup:solved
• Only in VR Workro om : For Mode switching (Mono in VR Workroom or Stereo in VR
Workroom) two “.bat” files have been added to the desktop to allow to switch from one
mode to another without going through the desktop integration settings and Services
restart.
For more details, See the VR Workroom I nstallation manual R5976989_01
• Single file downloader : One single file is used to perform an upgrad e o f the
projector : both firmware and server software are installed !
• Full screen source display is now also possible without logging on (displayed on the logon
screen )
Image 1-1
Stereo adjust in the VR Workroom
Image 1-2
Stereo adjust removed when source is not stereo
InfoT:
InfoT 699
Page 2 of 4
Barco service bulletin
1.2 Upgrade
CAUTION: This upgrade to V1.30 may only be done on projectors running
software V1.26.
Do not upgrade a projector that runs a software version older than V1.26
(< V1.26) !
If the projector uses a software version older than V1.26, first upgrade
to V1.26 !
How to u pg rade the projector ?
1.See the iCon service manual R5976824_04 for a detailed u pgrade procedure
InfoT:
InfoT 699
Page 4 of 4
/