DFI G7B630-B/G7B630-N/G7B630-NR User manual

G7B630-B/N/NR

System Board

User’s Manual

935-G7B632-300G

A03010038

Copyright

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior writ-

ten permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any ex-

press or implied warranties of merchantability or fitness for any par-

ticular purpose. The user will assume the entire risk of the use or the

results of the use of this document. Further, the manufacturer re-

serves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or en-

tity of such revisions or changes.

Trademarks

Product names or trademarks appearing in this manual are for iden-

tification purpose only and are the properties of the respective own-

ers.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communi-

cations. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following meas-

ures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

par

ty responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

About this Manual................................................................................

Warranty.................................................................................................

Static Electricity Precaution................................................................

Safety Measures.....................................................................................

About the Package...............................................................................

Before Using the System Board.........................................................

Chapter 1 - Introduction....................................................................

Specifications...................................................................................................................................

Features..............................................................................................................................................

Chapter 2 - Hardware Installation....................................................

System Board Layout ..........................................................................................................

System Memor

y..........................................................................................................................

CPU.......................................................................................................................................................

Jumper Settings............................................................................................................................

Rear Panel I/O Ports.............................................................................................................

I/O Connectors..........................................................................................................................

Chapter 3 - BIOS Setup......................................................................

Award BIOS Setup Utility.................................................................................................

Intel RAID BIOS........................................................................................................................

Updating the BIOS..................................................................................................................

Chapter 4 - Supported Softwares.....................................................

Chapter 5 - RAID

.................................................................................

Appendix A - Enabling Hyper-Threading Technology......................

Appendix B - System Error Messages...............................................

Appendix C - Troubleshooting..........................................................

Appendix D - Watchdog Sample Code..............................................

Appendix E - NLITE and AHCI Installation Guide...........................

5

6

7

8

11

15

18

22

28

34

45

60

99

100

102

127

132

135

137

141

143

About this Manual

An electronic file of this manual is included in the CD. To view the

user’s manual in the CD, insert the CD into a CD-ROM drive. The

autorun screen (Main Board Utility CD) will appear. Click “User’s

Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from

misuse of the product, inability to use the product, unauthorized

replacement or alteration of components and product specifica-

tions.

2. The warranty is void if the product has been subjected to physi-

cal abuse, improper installation, modification, accidents or unau-

thorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may

not, under any circumstances, attempt to perform service, adjust-

ments or repairs on the product, whether in or out of warranty.

It must be returned to the purchase point, factory or authorized

service agency for all such work.

4. We will not be liable for any indirect, special, incidental or

consequencial damages to the product that has been modified

or altered.

Introduction

1

6

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board,

components or devices even before installing them in your system

unit. Static electrical discharge can damage computer components

without causing any signs of physical damage. You must take extra

care in handling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its

anti-static bag until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of

the components, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connec-

tors. Hold modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor,

disk drive and other components. Perform the upgrade in-

struction procedures described at an ESD workstation

only. If such a station is not available, you can provide

some ESD protection by wearing an antistatic wrist strap

and attaching it to a metal part of the system chassis. If a

wrist strap is unavailable, establish and maintain contact

with the system chassis throughout any procedures requir-

ing ESD protection.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range

..

.

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

by

the manufacturer.

• Dispose of used batteries according to local ordinance.

1

Introduction

7

About the Package

The system board package contains the following items. If any of

these items are missing or damaged, please contact your dealer or

sales representative for assistance.

; The system board

; A user’s manual

; One IDE cable

; One FDD cable

; Two Serial ATA data cables

; Two Serial ATA power cables

; One bracket mounted with a serial port

; Two USB port cables

; One “Main Board Utility” CD

; One I/O shield

; One QR (Quick Reference)

The system board and accessories in the package may not come

similar to the information listed above. This may differ in accordance

to the sales region or models in which it was sold. For more infor-

mation about the standard package in your region, please contact

your dealer or sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need

at least the following internal components.

• A CPU

• Memory module

• Storage devices such as hard disk drive, CD-ROM, etc.

You will also need external system peripherals you intend to use

which will normally include at least a keyboard, a mouse and a video

display monitor.

Introduction

1

8

• LGA 775 socket for:

- Intel

®

Core

TM

2 Quad, Intel

®

Core

TM

2 Duo (Conroe family),

Intel

®

Pentium

®

D, Intel

®

Pentium

®

4 or Intel

®

Celeron, Intel

®

Celeron D

• Supports Intel Enhanced Memory 64 Technology (EMT64T)

• Supports Enhanced Intel SpeedStep Technology (EIST)

• Supports Intel Hyper-Threading Technology

• Supports 1066/800/533MHz FSB

• Intel

®

chipset

- Northbridge: Intel

®

Q965 Express chipset

- Southbridge: Intel

®

ICH8 (G7B630-B and G7B630-N)

Intel

®

ICH8DO (G7B630-NR)

• Four 240-pin DDR2 DIMM sockets

• Supports DDR2 533, DDR2 667 and DDR2 800 DIMMs

• Supports dual channel (128-bit wide) memory interface

• Supports up to 8GB system memory

• Supports non-ECC unbuffered DIMMs

• 1 PCI Express x16 slot

• 2 PCI Express x1 slots

• 4 PCI slots

• Built-in Intel Graphics Media Accelerator 3000

• Realtek ALC262 High Definition audio CODEC

• 2-channel audio output

• 1 stereo DAC supports 16/20/24-bit PCM format with 44.1/48/

96/192KHz sample rate

• 2 stereo ADCs support 16/20-bit PCM format with 44.1/48/96/

192KHz sample rate

• S/PDIF-in/out interface

• G7B630-B - Marvell 88E8056 PCI Express Gigabit Ethernet

controller

G7B630-N and G7B630-NR - Intel 82566DM and Marvell

88E8056 PCI Express Gigabit Ethernet controllers

• Supports 10Mbps, 100Mbps and 1Gbps data transmission

• IEEE 802.3 (10/100Mbps) and IEEE 802.3ab (1Gbps) compliant

• Supports SATA (Serial ATA) interfaces which are compliant with

SATA 1.0 specification

• G7B630-NR

- 6 Serial ATA ports

- SATA speed up to 3Gb/s

- RAID 0, RAID 1, RAID 5 and RAID 10

• G7B630-B and G7B630-N

- 4 Serial ATA ports

- SATA speed up to 3Gb/s

Processor

Chipset

System Memory

Expansion Slot

Graphics

Audio

LAN

Serial ATA

Chapter 1 - Introduction

Specifications

1

Introduction

9

IDE

Rear I/O

I/O Connectors

BIOS

Energy Efficient

Design

• JMicron JMB368 PCI Express to PATA host controller

• Supports up to 2 UltraDMA 133Mbps IDE devices

• 1 mini-DIN-6 PS/2 mouse port

• 1 mini-DIN-6 PS/2 keyboard port

• 1 DB-25 parallel port

• 1 DB-9 serial port

• 1 DB-15 VGA port

• 1 RJ45 LAN port (G7B630-B)

2 RJ45 LAN ports (G7B630-N and G7B630-NR)

• 4 USB 2.0/1.1 ports

• Mic-in, line-in and line-out jacks

• 3 connectors for 6 additional external USB 2.0/1.1 ports

• 1 connector for an external COM 2 port

• 1 Digital I/O connector

• 1 front audio connector for line-out and mic-in jacks

• 1 CD-in internal audio connector

• 1 S/PDIF-in/out connector

• 1 connector for IrDA interface

• 6 Serial ATA connectors (G7B630-NR)

4 Serial ATA connectors (G7B630-B and G7B630-N)

• 1 40-pin IDE connector

• 1 floppy connector

• 1 24-pin ATX power connector

• 1 4-pin 12V power connector

• 1 chassis open connector

• 1 front panel connector

• 3 4-wire fan connectors

• Award BIOS

• 4Mbit SPI flash memory (G7B630-B)

8Mbit SPI flash memory (G7B630-N/NR)

• Supports ACPI specification and OS Directed Power Manage-

ment

• Supports ACPI STR (Suspend to RAM) function

• Wake-On-Events include:

- Wake-On-PS/2 Keyboard/Mouse

- Wake-On-USB Keyboard/Mouse

- Wake-On-LAN

- Wake-On-Ring

- RTC timer to power-on the system

• System power management supported

• CPU stopped clock control

• Microsoft

®

/Intel

®

APM 1.2 compliant

• Soft Power supported - ACPI v2.0 specification

• AC power failure recovery

Introduction

1

10

Damage Free

Intelligence

Temperature

Humidity

PCB

• Monitors CPU/system temperature and overheat alarm

•

Monitors Vcore/VCC3/VBAT/3VSB/12V/1.25V/1.8V/5V voltages

and failure alarm

• Monitors CPU/2nd/system fan speed

• Read back capability that displays temperature, voltage and fan

speed

• Watchdog Timer function

• Operating: 0

o

C to 60

o

C

• Non-operating: -40

o

C to 85

o

C

• Operating: 10% to 90%

• 4 layers, ATX form factor

• 30.5cm (12") x 24.4cm (9.6")

1

Introduction

11

Features

The Watchdog Timer function allows your

application to regularly “clear” the system at

the set time interval. If the system hangs or fails to function, it will

reset at the set time interval so that your system will continue to

operate.

The system board supports Intel proces-

sors with Hyper-Threading Technology. Ena-

bling the functionality of Hyper-Threading

Technology for your computer system requires ALL of the following

platforms.

Components:

• CPU - an Intel

®

Pentium

®

4 Processor with HT Technology

• Chipset - an Intel

®

chipset that supports HT Technology

• BIOS - a BIOS that supports HT Technology and has it enabled

• OS - an operating system that includes optimizations for HT

Technology

Please refer to Appendix A for information about enabling the func-

tionality of the Hyper-Threading Technology. For more information on

Hyper-Threading Technology, go to: www.intel.com/info/hyperthreading.

DDR2 is a higher performance DDR technology

whose data transfer rate delivers bandwidth of 4.3

GB per second and beyond. That is twice the speed of the conven-

tional DDR without increasing its power consumption. DDR2

SDRAM modules work at 1.8V supply compared to 2.6V memory

voltage for DDR modules. DDR2 also incorporates new innovations

such as the On-Die Termination (ODT) as well as larger 4-bit pre-

fetch against DDR which fetches 2 bits per clock cycle.

The graphics engine of the built-in Intel

®

Graphics

Media Accelerator 3000 consists of a scalable array

of symmetric processing components known as execution units (EUs)

which can be programmed to dynamically process graphics or media

data alike. Execution units support dynamic load balancing, multi-

threading, and multi-functional data processing, resulting in increased

performance to enable a more compelling gaming and visual experi-

ence.

watchdog timer

graphics

hyper-threading

technology

DDR2

Introduction

1

12

S/PDIF is a standard audio file transfer format that

transfers digital audio signals to a device without

having to be converted first to an analog format. This prevents the

quality of the audio signal from degrading whenever it is converted

to analog. S/PDIF is usually found on digital audio equipment such as

a DAT machine or audio processing device. The S/PDIF connector on

the system board sends surround sound and 3D audio signal out-

puts to amplifiers and speakers and to digital recording devices like

CD recorders.

Serial ATA is a storage interface that is compliant

with SATA 1.0 specification. With speed of up to

3Gb/s, it improves hard drive performance faster than the standard

parallel ATA whose data transfer rate is 100MB/s. G7B630-NR

allows configuring RAID on Serial ATA drives. It supports RAID 0,

RAID 1, RAID 5 and RAID 10.

The JMicron JMB368 chip supports up to two

UltraDMA 133Mbps IDE devices.

The Intel 82566DM and Marvell 88E8056 PCI

Express Gigabit Ethernet controllers support up

to 1Gbps data transmission.

The system board is equipped with an IrDA connec-

tor for wireless connectivity between your computer

and peripheral devices. The IRDA (Infrared Data Association) specifi-

cation supports data transfers up to 115Kbps baud rate speed.

irda

gigabit lan

S/PDIF

IDE

SERIAL ATA

1

Introduction

13

The system board supports USB 2.0 and USB 1.1

ports. USB 1.1 supports 12Mb/second bandwidth

while USB 2.0 supports 480Mb/second bandwidth providing a

marked improvement in device transfer speeds between your com-

puter and a wide range of simultaneously accessible external Plug

and Play peripherals.

This feature allows the system that is in the

Suspend mode or Soft Power Off mode to

wake-up/power-on to respond to calls coming from an external mo-

dem or respond to calls from a modem PCI card that uses the PCI

PME (Power Management Event) signal to remotely wake up the

PC.

Important:

The 5V_standby power source of your power supply must sup-

port

≥

720mA.

This feature allows the network to remotely

wake up a Soft Power Down (Soft-Off) PC.

It is supported via the onboard LAN port or via a PCI LAN card

that uses the PCI PME (Power Management Event) signal. However,

if your system is in the Suspend mode, you can power-on the system

only through an IRQ or DMA interrupt.

Important:

The 5V_standby power source of your power supply must sup-

port

≥

720mA.

This function allows you to use the PS/2

keyboard or PS/2 mouse to power-on the

system.

Important:

The 5V_standby power source of your power supply must sup-

port

≥

720mA.

USB

wake-on-lan

wake-on-ring

wake-on-PS/2

Introduction

1

14

This function allows you to use a USB key-

board or USB mouse to wake up a system

from the S3 (STR - Suspend To RAM) state.

Important:

If you are using the Wake-On-USB Keyboard/Mouse function for

2 USB ports, the 5V_standby power source of your power sup-

ply must support

≥

1.5A. For 3 or more USB ports, the

5V_standby power source of your power supply must support

≥

2A.

The RTC installed on the system board allows your

system to automatically power-on on the set date

and time.

The system board is designed to meet the ACPI

(Advanced Configuration and Power Interface) speci-

fication. ACPI has energy saving features that enables PCs to imple-

ment Power Management and Plug-and-Play with operating systems

that support OS Direct Power Management. Currently, only Win-

dows

®®

®

2000/XP supports the ACPI function. ACPI when enabled in

the Power Management Setup will allow you to use the Suspend to

RAM function.

With the Suspend to RAM function enabled, you can power-off the

system at once by pressing the power button or selecting “Standby”

when you shut down Windows

®®

®

2000/XP without having to go

through the sometimes tiresome process of closing files, applications

and operating system. This is because the system is capable of stor-

ing all programs and data files during the entire operating session

into RAM (Random Access Memory) when it powers-off. The oper-

ating session will resume exactly where you left off the next time you

power-on the system.

Important:

The 5V_standby power source of your power supply must sup-

port

≥

720mA.

When power returns after an AC power fail-

ure, you may choose to either power-on the

system manually or let the system power-on

automatically.

Power failure

recovery

wake-on-USB

rtc timer

ACPI STR

15

2

Hardware Installation

System Board Layout

Chapter 2 - Hardware Installation

G7B630-B

Mouse

KB

LAN 1

USB 0-1

Mic-in

Line-in

Line-out

1

PS/2 power

select ( 1)JP

PCI Express x16

CD-in

1

Front

audio

1

S/PDIF

PCI 4

PCI 3

PCI 2

PCI 1

USB 4-5

1

USB 6-7

1

USB 8-9

1

Standby Power LED

DDR2-1

DDR2-2

DDR2-3

DDR2-4

1

Clear CMOS

()JP7

1

FDD

1

13

24

12

COM 2

1

2nd Fan

1

CPU Fan

1

IrDA

Front

1

System Fan

1

+12V

power

12

56

COM 2 RS232/AUX

select (JP6)

SATA 4 SATA 0

SATA 5

11

1

Digital I/O

Intel

Q965

Intel

ICH8

Parallel

VGA

COM 1

LGA 775

1

Chassis

open

Winbond

I/O chip

ATX

Marvell

88E8056

Realtek

ALC262

PCI Express x1

Battery

panel

JMicron

JMB368

IDE

power

1

USB 0-3 power

select ( )JP2

USB 4-7 power

select ( )JP3

USB 8-9 power

select ( )JP4

SPI Flash

BIOS

SATA 1

1

Power-on

select ( )JP9

USB 2-3

16

2

Hardware Installation

G7B630-N

Mouse

KB

LAN 1

USB 0-1

Mic-in

Line-in

Line-out

1

PS/2 power

select ( 1)JP

PCI Express x16

Front

audio

1

S/PDIF

PCI 4

PCI 3

PCI 2

PCI 1

USB 4-5

1

USB 6-7

1

USB 8-9

1

Standby Power LED

DDR2-1

DDR2-2

DDR2-3

DDR2-4

1

Clear CMOS

()JP7

1

FDD

1

13

24

12

COM 2

1

2nd Fan

1

CPU Fan

1

IrDA

Front

1

System Fan

1

+12V

power

12

56

COM 2 RS232/AUX

select (JP6)

SATA 4 SATA 0

SATA 5

11

1

Digital I/O

Intel

Q965

Intel

ICH8

Parallel

VGA

COM 1

LAN 2

USB 2-3

LGA 775

1

Chassis

open

Winbond

I/O chip

ATX

Marvell

88E8056

82566DM

Intel

Realtek

ALC262

PCI Express x1

Battery

panel

JMicron

JMB368

IDE

power

1

USB 0-3 power

select ( )JP2

USB 4-7 power

select ( )JP3

USB 8-9 power

select ( )JP4

SPI Flash

BIOS

SATA 1

1

Power-on

select ( )JP9

CD-in

1

17

2

Hardware Installation

Note:

The illustrations on the following pages are based on the G7B630-

NR system board.

G7B630-NR

Mouse

KB

LAN 1

USB 0-1

Mic-in

Line-in

Line-out

1

PS/2 power

select ( 1)JP

PCI Express x16

Front

audio

1

S/PDIF

PCI 4

PCI 3

PCI 2

PCI 1

USB 4-5

1

USB 6-7

1

USB 8-9

1

Standby Power LED

DDR2-1

DDR2-2

DDR2-3

DDR2-4

1

Clear CMOS

()JP7

1

FDD

1

13

24

12

COM 2

1

2nd Fan

1

CPU Fan

1

IrDA

Front

1

System Fan

1

+12V

power

12

56

COM 2 RS232/AUX

select (JP6)

SATA 4 SATA 0

SATA 5

11

1

Digital I/O

Intel

Q965

Intel

ICH8DO

Parallel

VGA

COM 1

LAN 2

USB 2-3

LGA 775

1

Chassis

open

Winbond

I/O chip

ATX

Marvell

88E8056

82566DM

Intel

Realtek

ALC262

PCI Express x1

Battery

panel

JMicron

JMB368

IDE

power

1

USB 0-3 power

select ( )JP2

USB 4-7 power

select ( )JP3

USB 8-9 power

select ( )JP4

SPI Flash

BIOS

SATA 2

SATA 3

1

SATA 1

1

Power-on

select ( )JP9

CD-in

1

18

2

Hardware Installation

Warning:

Electrostatic discharge (ESD) can damage your system board, proces-

sor, disk drives, add-in boards, and other components. Perform the

upgrade instruction procedures described at an ESD workstation only.

If such a station is not available, you can provide some ESD protec-

tion by wearing an antistatic wrist strap and attaching it to a metal

part of the system chassis. If a wrist strap is unavailable, establish

and maintain contact with the system chassis throughout any proce-

dures requiring ESD protection.

System Memory

The system board supports 240-pin DDR2 DIMM sockets. The four

DDR2 DIMM sockets on the system board are divided into 2 chan-

nels:

Channel A - DDR2-1 and DDR2-3

Channel B - DDR2-2 and DDR2-4

.

DDR2-1

DDR2-2

DDR2-3

DDR2-4

19

2

Hardware Installation

The system board supports the following memory interface.

Single Channel (SC)

Data will be accessed in chunks of 64 bits (8B) from the memory

channels.

Dual Channel (DC)

Data will be accessed in chunks of 128 bits from the memory chan-

nels. Dual channel provides better system performance because it

doubles the data transfer rate.

• DIMMs are on the same channel.

• DIMMs in a channel can be identical or

completely different. However, we highly rec-

ommend using identical DIMMs.

• Not all slots need to be populated.

• DIMMs of the same memory configura-

tion are on different channels.

Single Channel

Dual Channel

20

2

Hardware Installation

Installing the DIM Module

1. Make sure the PC and all other peripheral devices connected to

it has been powered down.

2. Disconnect all power cords and cables.

3. Locate the DDR2 socket on the system board.

4. Push the “ejector tabs” which are at the ends of the socket to

the side.

Ejector

tab

5. Note how the module is keyed to the socket.

DDR2 sockets

Ejector

tab

Key

Notch

Page is loading ...

DFI G7B630-B/G7B630-N/G7B630-NR User manual

DFI G7B630-B/G7B630-N/G7B630-NR User manual

Related papers

Other documents