IS-52160-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
5) (If second loop is already aached to canopy, proceed
to next step). Pass threaded pipe at end of second
loop through hole in canopy. Pass xture wire through
lockwasher[N] and thread lockwasher onto threaded
pipe protruding from inside canopy. Pass xture wire
through hole in hexnut[M] and thread hexnut onto end
of threaded pipe.
6) Aach chain link[F] to small loop at end of stem and to
loop on canopy. Close the open chain link by placing a piece
of cloth over the open link and using a pair of pliers gently
squeeze the link closed.
7) Find the appropriate threaded holes on mounng
strap[G]. Assemble mounng screws[H] into threaded
holes.
8) Aach mounng strap to outlet box[I] using the strap
mounng screws[O]. The mounng strap can be
adjusted to suit posion of xture.
9) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is
provided,aach ground wire from outlet box under
cupped washer and green ground screw, then thread
into mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector aer following the above steps. Never connect
ground wire to black or white power supply wires.
10) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth
(see illus.)
Neutral Wire
11) Push xture to ceiling, carefully passing mounng screws
through holes in canopy[J]. NOTE: Be certain wires do
not get pinched between canopy and ceiling.
12) Use knobs[K] and lockwashers[L] to secure canopy.
Tighten to secure.
13) Install the recommended bulbs. (Not supplied).
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
[A] Coupling
[B] Stem
[C] Short
Threaded
Tubes
[D] First Loop
[E] Second Loop
[F] Chain Link
[G] Mounting
Strap
[H] Mounting
Screws
[I] Outlet Box
[J] Canopy
[K] Knobs
[L] Lockwashers
[M] Hexnut
[N] Lockwasher
[O] Strap
Mounting
Screws
1) Pass xture wire from the coupling on top of xture
through a stem[B] and threaded tubes[C] and screw
stem into coupling[A] on top of the main body.
NOTE: Thread locking compound must be applied to
all stem threads as noted with symbol (4) to prevent
accidental rotaon of xture during cleaning, relamping,
etc.
2) Pass xture wire through desired amount of stems and
screw stems together using supplied short threaded
tubes.
3) Pass xture wire from last stem through rst loop[D].
Thread rst loop onto end of last stem.
4) Pass xture wire through second loop[E] and through
hole in canopy[J].
Installaon Instrucons (connued)
I
G
O
J
D
B
C
M
H
F
►
►
N
K
L
►
A
E