IS-52119-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
I
G
O
J
D
B
C
M
H
F
E
►
►
N
K
L
►
A
P
C
N
M
A
STEM HUNG MOUNTING INSTRUCTIONS
1) NOTE: At least one (1) 6 inch tube must be used during mounng. Pass xture
wire from the coupling on top of xture through a stem [B] and threaded
tubes [C] and screw stem into coupling [A] on top of the main body.
NOTE: Thread locking compound must be applied to all stem threads as
noted with symbol (4) to prevent accidental rotaon of xture during
cleaning, relamping, etc.
2) Pass xture wire through desired amount of stems and screw stems together
using supplied short threaded tubes.
3) Pass xture wire from last stem through rst loop [D]. Thread rst loop onto
end of last stem.
4) Pass xture wire through second loop [E] and through hole in canopy.
5) (If second loop is already aached to canopy, proceed to next step). Pass
threaded pipe at end of second loop through hole in canopy. Thread
lockwasher [N] onto threaded pipe protruding from inside canopy. Pass
xture wire through hole in hexnut [M] and thread hexnut onto end of
threaded pipe.
6) Aach chain link [F] to small loop at end of stem and to loop on canopy. Close
the open chain link by placing a piece of cloth over the open link and using a pair
of pliers gently squeeze the link closed.
7) Find the appropriate threaded holes on mounng strap [G]. Assemble
mounng screws [H] into threaded holes.
8) Aach mounng strap to outlet box [I] using the strap mounng screws [O].
The mounng strap can be adjusted to suit posion of xture.
9) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a hole and two raised
dimples, wrap ground wire from outlet box around green ground screw,
and thread into hole.
b) On xtures where a cupped washer is provided,aach ground wire from
outlet box under cupped washer and green ground screw, then thread
into mounng strap.
If xture is provided with ground wire, connect xture ground wire to outlet
box ground wire with wire connector aer following the above steps. Never
connect ground wire to black or white power supply wires.
10) Make wire connecon. Reference chart below for correct connecons and
wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth
(see illus.)
Neutral Wire
11) Push xture to ceiling, carefully passing mounng screws through holes in
canopy [J]. NOTE: Be certain wires do not get pinched between canopy and
ceiling.
12) Use knobs [K] and lockwashers [L] to secure canopy. Tighten to secure.
13) Install the recommended bulbs. (Not supplied).
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before
starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance with the Naonal Electrical
Code (NEC) and all local code specicaons. If you are not familiar with code
requirements, installaon by a cered electrician is recommended.
[A] Coupling
[B] Stem
[C] Short Threaded
Tubes
[D] First Loop
[E] Second Loop
[F] Chain Link
[G] Mounting Strap
[H] Mounting Screws
[I] Outlet Box
[J] Canopy
[K] Knobs
[L] Lockwashers
[M] Hexnut
[N] Lockwasher
[O] Strap Mounting
Screws
[P] 3 Inch Stem
Installaon Instrucons
SEMI-FLUSH MOUNTING INSTRUCTIONS
1) Pass xture wire from the coupling [A] on top of xture through the 3 inch
stem [P] and threaded tube [C] and screw stem into coupling on top of the
main body.
2) Pass threaded pipe at end of 3 inch stem through hole in canopy. Thread
lockwasher [N] onto threaded pipe protruding from inside canopy. Pass
xture wire through hole in hexnut and thread hexnut [M] onto end of
threaded pipe.
3) Follow steps 7 thru 13 from “STEM HUNG MOUNTING INSTRUCTIONS” to
complete installaon.
STEM HUNG MOUNTING
SEMI-FLUSH MOUNTING
Page is loading ...
Page is loading ...
/
