Wacker Neuson 5055 User manual

Type
User manual
Operator’s Manual
Wheel loader
550 / 5055
Machine model 349-03
From serial no. 349 03 0001
Version 1.0
Document number 1000311334
Language [us]
1000311334
Document ation
Documents Order no. Order no.
Operator’s Manual [us] 1000311334
Copyright – 2014 Kramer-Werke GmbH
Printed in Germany
All rights reserved, in particular the copyright, the right of reproduction and the right of distribution applicable
worldwide.
No part of this publication may be reproduced, translated or used in any form or by any means – graphic,
electronic or mechanical including photocopying, recording, taping or information storage or retrieval systems –
without prior permission in writing from the manufacturer.
No reproduction or translation of this publication, in whole or part, without the written consent of
KRAMER-WERKE GmbH.
Violations of legal regulations, in particular of the copyright protection, shall be subject to civil and criminal
prosecution.
KRAMER-WERKE GmbH keep abreast of the latest technical developments and constantly improve their
products. For this reason, we may from time to time need to make changes to diagrams and descriptions in this
documentation which do not reflect products that have already been delivered and that will not be implemented
on these machines.
Technical data, dimensions and weights are only given as an indication. Responsibility for errors or omissions
not accepted.
The cover features the machine with possible optional equipment.
Exclusively built for Wacker Neuson.
Kramer-Werke GmbH
Wacker-Neuson-Str. 1
D-88630 Pfullendorf
Tel. 0080090209020
www.kramer.de
Legend
Original Operator’s Manual x
Translation of original Opera-
tor’s Manual
Version 1.0
Date 04/2014
Document BA 34903 *
BA 34903 * 1.0 * BA_34903_V1_usIVZ.fm I-1
Table of contents
Table of contents
1Foreword
1.1 Operator’s Manual................................................................................................................................ 1-1
1.2 Warranty and liability ............................................................................................................................ 1-4
2 Safety
2.1 Safety symbols and signal words ......................................................................................................... 2-1
2.2 Conduct and safety instructions ........................................................................................................... 2-2
2.3 Qualification of operating and maintenance personnel......................................................................... 2-3
2.4 Operation.............................................................................................................................................. 2-4
2.5 Lifting gear applications........................................................................................................................ 2-8
2.6 Trailer operation ................................................................................................................................. 2-10
2.7 Operation of attachments ................................................................................................................... 2-11
2.8 Towing, loading and transporting ....................................................................................................... 2-12
2.9 Maintenance....................................................................................................................................... 2-15
2.10 Measures for avoiding risks................................................................................................................ 2-18
3 Introduction
3.1 Machine overview................................................................................................................................. 3-1
3.2 Brief description of machine ................................................................................................................. 3-3
3.3 Notices and regulations on use ............................................................................................................ 3-5
3.4 Labels................................................................................................................................................. 3-11
4 Putting into operation
4.1 Cabin/control stand............................................................................................................................... 4-1
4.2 Overview of control elements ............................................................................................................. 4-25
4.3 Indicator lights and warning lights (overview)..................................................................................... 4-30
4.4 Preparatory work ................................................................................................................................ 4-33
4.5 Starting and stopping the engine........................................................................................................ 4-41
5Operation
5.1 Steering system.................................................................................................................................... 5-1
5.2 Accelerator actuation............................................................................................................................ 5-4
5.3 Brakes .................................................................................................................................................. 5-5
5.4 Travel operation.................................................................................................................................... 5-7
5.5 Differential lock................................................................................................................................... 5-12
5.6 Lights/signaling system ...................................................................................................................... 5-13
5.7 Wiper/wash system ............................................................................................................................ 5-18
5.8 Heating, ventilation and air conditioning system (option) ................................................................... 5-20
5.9 Operating hydraulics........................................................................................................................... 5-21
5.10 Attachments........................................................................................................................................ 5-29
5.11 Work operation ................................................................................................................................... 5-35
5.12 Emergency lowering........................................................................................................................... 5-53
5.13 Options ............................................................................................................................................... 5-54
5.14 Putting out of operation/back into operation....................................................................................... 5-61
5.15 Permanently putting out of operation.................................................................................................. 5-63
6Transportation
6.1 Towing the machine ............................................................................................................................. 6-1
6.2 Loading the machine ............................................................................................................................ 6-4
6.3 Transporting the machine..................................................................................................................... 6-8
Table of contents
I-2 BA 34903 * 1.0 * BA_34903_V1_usIVZ.fm
Table of contents
7 Maintenance
7.1 Notice on maintenance......................................................................................................................... 7-1
7.2 Maintenance overview.......................................................................................................................... 7-3
7.3 Fluids and lubricants........................................................................................................................... 7-10
7.4 Maintenance accesses....................................................................................................................... 7-14
7.5 Cleaning and maintenance................................................................................................................. 7-15
7.6 Lubrication work.................................................................................................................................. 7-21
7.7 Fuel system ........................................................................................................................................ 7-24
7.8 Engine lubrication system................................................................................................................... 7-27
7.9 Cooling system................................................................................................................................... 7-30
7.10 Air filter................................................................................................................................................ 7-35
7.11 V-belt/toothed belt............................................................................................................................... 7-38
7.12 Hydraulic system ................................................................................................................................ 7-41
7.13 Electrical system................................................................................................................................. 7-48
7.14 Heating, ventilation and air conditioning system................................................................................. 7-52
7.15 Washer system................................................................................................................................... 7-54
7.16 Axles/traveling drive............................................................................................................................ 7-55
7.17 Braking system................................................................................................................................... 7-56
7.18 Tires.................................................................................................................................................... 7-58
7.19 Maintenance of attachments............................................................................................................... 7-61
7.20 Maintenance of options....................................................................................................................... 7-62
7.21 Exhaust gas treatment........................................................................................................................ 7-67
7.22 Machine preservation ......................................................................................................................... 7-71
8Malfunctions
8.1 Diesel engine malfunctions................................................................................................................... 8-1
8.2 Drive malfunctions................................................................................................................................ 8-4
8.3 Malfunctions of the hydraulic system.................................................................................................... 8-4
8.4 Malfunctions of the electrical system.................................................................................................... 8-4
8.5 Malfunctions in the air conditioning system (option)............................................................................. 8-5
9 Technical data
9.1 Model and trade names........................................................................................................................ 9-1
9.2 Engine................................................................................................................................................... 9-1
9.3 Traveling drive/axles............................................................................................................................. 9-2
9.4 Brakes................................................................................................................................................... 9-4
9.5 Tires...................................................................................................................................................... 9-5
9.6 Steering system.................................................................................................................................... 9-5
9.7 Operating hydraulics............................................................................................................................. 9-6
9.8 Electrical system................................................................................................................................... 9-8
9.9 Tightening torques.............................................................................................................................. 9-11
9.10 Coolant ............................................................................................................................................... 9-12
9.11 Noise emissions.................................................................................................................................. 9-12
9.12 Vibration.............................................................................................................................................. 9-13
9.13 Weight................................................................................................................................................. 9-13
9.14 Payload/lift capacity/stability............................................................................................................... 9-14
9.15 Dimensions......................................................................................................................................... 9-15
Index
Index ..............................................................................................................................................................S-1
BA 34903 * 1.0 * 34903_01_Vorwort.fm 1-1
Foreword 1
1 Foreword
1.1 Operators Manual
Important notices on the operating personnel
This Operator’s Manual applies to machine model 349-03 and is intended
for use by the operator and operating company.
It provides instructions on the use, the adjustment, the operation and the
maintenance of the machine.
Before driving or using the machine for the first time, the operator must be
briefed on this machine and must carefully read and understand this
Operator’s Manual, in particular chapter “Safety instructions”.
Work on the machine may only be performed by trained and instructed
personnel that has been authorized by the operating company. Any
person involved in operation, inspection, maintenance, servicing, repair
work or transport of the machine must read, understand and follow the
complete instructions in the Operator’s Manual and in particular the safety
instructions.
The buyer/operating company is responsible for the operators’ training in
safe working on and with the machine. Kramer-Werke GmbH
recommends repeating training at regular intervals.
The buyer/operating company is responsible for ensuring that any
additional safety regulations applicable in the country of use of the
machine are followed.
The machine may only be operated by persons who are physically,
mentally and professionally suited for this work.
Persons under the influence of alcohol or drugs may not use the
machine.
The operator is the person operating and/or driving the machine.
Before putting the machine into operation, the operator of the machine
must ensure that it is in a perfect condition, and during operation he
must pay attention to the regulations regarding operation.
The operator is responsible for ensuring that the machine and its use
do not constitute a risk.
Before working with the machine, the operator must familiarize himself
with all the control elements and their functions, and with the handling
of the machine.
Information
Careful and prudent working is the best way to avoid accidents!
Foreword
Table of contents
Index
1-2 BA 34903 * 1.0 * 34903_01_Vorwort.fm
1 Foreword
Important notices on this Operators Manual
The Operator’s Manual and amendments form part of the machine and
must always be available at the place of use of the machine.
Store this Operator’s Manual in the storage compartment or net
provided for this in the cabin.
Immediately replace an incomplete or illegible Operator’s Manual by a
new one.
In addition to the Operator’s Manual, observe and instruct the operator
in all other generally applicable legal and other mandatory regulations
relevant to accident prevention and environmental protection.
Please contact your dealer if you require more information on the
machine and the Operator’s Manual.
Kramer-Werke keep abreast of the latest technical developments and
constantly improve their products. For this reason, we may from time to
time need to make changes to diagrams and descriptions in this
documentation which do not reflect products which have already been
delivered and which will not be implemented on these machines.
Technical data, dimensions and weights are only given as an
indication. Responsibility for errors or omissions not accepted.
BA 34903 * 1.0 * 34903_01_Vorwort.fm 1-3
Foreword 1
Explanation of symbols and abbreviations
The indication left or right in the descriptions always refers to the travel
direction of the machine.
Symbols Explanation
Identifies a general list
1
Identifies a list in a table (position numbers)
2
1.
Identifies activities that must be performed in a cer-
tain order
2.
Identifies results
Identifies things to be avoided in the warning and
safety instructions
Abbreviations Explanation
Rpm Revolution per minute
l/min Litres per minute
MIN minimum
MAX. maximum
e.g. for example
or
sec Seconds
Fig. Figure
o/h Operating hours
Order no. Order, item or part number
ROPS Roll Over Protective Structure
FOPS Falling Object Protective Structure
Trucks Trucks
1-4 BA 34903 * 1.0 * 34903_01_Vorwort.fm
1 Foreword
1.2 Warranty and liability
Warranty claims can only be made if the conditions of warranty have been
observed.
They are included in the General Conditions of Sales and Delivery for new
machines and spare parts sold by the dealers. Furthermore, the
instructions in this Operator’s Manual must be observed.
Notice on maintenance, repairs and spare parts
Operational safety and readiness of the machine do not only depend on
your reliable control, but also on maintenance and servicing of the
machine. This is why regular maintenance and service work is absolutely
necessary.
Information
Repair work, maintenance or modifications may only be performed by
specifically trained technical personnel or by a service center!
Follow the instructions, in particular in chapters “Notices on maintenance”
and “Maintenance overview”.
Information
Insist on using original spare parts for repairs!
The machine’s permits, certifications, registrations, etc., may be
withdrawn if machine parts/components with a prescribed condition or
quality, or machine parts/components that can put persons at risk during
operation, are subsequently modified or exchanged.
BA 34903 * 1.0 * Sicherheit.fm 2-1
Safety 2
2 Safety
2.1 Safety symbols and signal words
Explanation
The following symbol identifies safety instructions. It is used for warning
against potential personal risk or danger.
DANGER
DANGER identifies a situation causing death or serious injury if it is
not avoided.
Consequences in case of non-observance.
Avoidance of injury or death.
WARNING
WARNING identifies a situation that can cause death or serious
injury if it is not avoided.
Consequences in case of non-observance.
Avoidance of injury or death.
CAUTION
CAUTION identifies a situation that can cause injury if it is not
avoided.
Consequences in case of non-observance.
Avoidance of injury.
NOTICE
NOTICE identifies a situation that causes damage to the machine if it is
not observed.
Avoidance of damage to property.
Safety
2-2 BA 34903 * 1.0 * Sicherheit.fm
2 Safety
2.2 Conduct and safety instructions
Prerequisites for operation
The machine has been designed and built in accordance with state-of-
the-art standards and the recognized safety regulations.
Nevertheless its use can cause danger to the operator or other
persons, or damage to the machine.
Store this Operator’s Manual in the place provided for this in or on the
machine. Immediately replace a damaged or illegible Operator’s
Manual and any supplements to it.
The machine must only be operated in accordance with its designated
use and the instructions set forth in this Operator’s Manual.
The operator and owner are obligated not to put into operation or
operate a damaged or malfunctioning machine.
- If a damage or malfunction occurs during operation, put the machine
out of operation immediately and secure it against restart.
- Have all malfunctions jeopardizing the safety of the operator or other
persons immediately repaired by a Wacker Neuson service center.
Do not put the machine into operation or operate it after an accident;
have it inspected for damage by a Wacker Neuson service center.
- Have the seat belt replaced by a Wacker Neuson service center after
an accident, even if there is no visible damage.
- Cabin and protective structures
Remove all dirt, snow and ice from climbing aids (handholds,
footholds, handrails, for example).
The owner is responsible for requiring the operating and maintenance
personnel to wear protective clothing and equipment as required by the
circumstances.
BA 34903 * 1.0 * Sicherheit.fm 2-3
Safety 2
2.3 Qualification of operating and maintenance personnel
Owners duties
Only allow specifically authorized, trained and experienced persons to
operate, drive and perform maintenance on the machine.
Do not allow persons to be trained or instructed by anyone other than
an authorized and experienced person.
Have persons to be trained or instructed practise under supervision
until they are familiar with the machine and its behavior (with the
steering and braking behavior, for example).
Children and persons under the influence of alcohol, drugs or medicine
are not allowed to access the machine or operate it.
Clearly and unequivocally define the responsibilities of the operating
and maintenance personnel.
Clearly and unequivocally define the responsibilities on the job site,
also in view of traffic regulations.
Give the operator the authority to refuse instructions by other persons
that are contrary to safety.
Have the machine serviced and repaired only by a Wacker Neuson
service center.
Required knowledge of operator
The operator is responsible for other persons.
Avoid any operational mode that might be prejudicial to safety.
The specific national driving license is required.
The machine may only be operated by authorized and safety-
conscious persons who are fully aware of the risks involved in
operating the machine.
The operator and owner are obligated to operate the machine only in a
safe and working condition.
All persons working on or with the machine must have read and under-
stood the safety instructions in this Operator’s Manual before starting
work.
Follow, and instruct the operator in, legal and other mandatory regula-
tions relevant to accident prevention.
Observe and instruct the operator in regulations regarding road traffic
and environmental protection.
Use only the defined accesses for getting on and off the machine.
Be familiar with the emergency exit of the machine.
Preparatory measures for the operator
Before starting, check the machine whether it can be driven and
operated safely.
Tie back long hair and remove all jewellery.
Wear close-fitting work clothes that do not hinder movement.
2-4 BA 34903 * 1.0 * Sicherheit.fm
2 Safety
2.4 Operation
Preparatory measures
Operation is only allowed with correctly installed and intact protective
structures.
Keep the machine clean. This reduces injury, accident and fire
hazards.
Safely store objects you carry with you at the places provided for this
(storage compartment, drinks holder, for example).
Do not carry objects with you that protrude into the operator’s work
space. They can create another danger in case of an accident.
Observe all safety, warning and information labels.
Start and operate the machine only with the seat belt fastened and only
from the place provided for this.
Check the condition and the fastening of the seat belt. Have malfunc-
tioning seat belts and mounting hardware replaced by a Wacker
Neuson service center.
Before starting work, adjust the seating position so that all control
elements can be reached and fully operated.
Perform the personal adjustment at machine standstill only (operator
seat, steering column, for example).
Ensure that all safety devices are properly installed and functional
before starting work.
Before starting work or after interrupting work, ensure that the brake,
steering, signaling and light systems are functional.
Before putting the machine into operation, ensure that nobody is in the
danger zone.
BA 34903 * 1.0 * Sicherheit.fm 2-5
Safety 2
Job site
The operator is responsible for other persons.
Before starting work, familiarize yourself with the job site. This applies
to, for example:
- Obstacles in the working and traveling area
- Any barriers separating the job site from public roads
- Soil weight-bearing capacity
- Existing overhead and underground lines
- Special operating conditions (dust, steam, smoke, asbestos, for
example)
The operator must know the maximum dimensions of the machine and
the attachment – see “Technical data”.
Maintain a safe distance (buildings, edges of building pits, for
example).
When working in buildings or in enclosed areas, look out for:
- Height of the ceiling/clearances
- Width of entries/passages
- Maximum load of ceilings and floors
- Sufficient room ventilation (risk of carbon monoxide poisoning, for
example)
Use existing visual aids to stay aware of the danger zone.
In conditions of darkness and poor visibility, switch on existing work
lights and ensure that motorists are not blinded by these lights.
If the existing lights of the machine are not sufficient for performing
work safely, ensure additional lighting of the job site.
Due to hot machine parts, maintain a safe distance from easily
flammable material (hay, dry leaves, for example).
Danger zone
The danger zone is the area in which persons are in danger due to the
movements of the machine, the attachment, and/or the load.
The danger zone also includes the area that can be affected by falling
material, equipment or by parts that are thrown out.
Extend the danger zone sufficiently in the immediate vicinity of
buildings, scaffolds or other elements of construction.
Seal off the danger zone should it not be possible to keep a sufficient
safety distance.
Stop work immediately if persons do not stay clear of the danger zone.
2-6 BA 34903 * 1.0 * Sicherheit.fm
2 Safety
Carrying passengers
Carrying passengers with the machine is PROHIBITED.
Carrying passengers on/in attachments/tools is PROHIBITED.
Carrying passengers on/in trailers is PROHIBITED.
Mechanical integrity
The operator and owner are obligated to operate the machine only in a
safe and working condition.
Operate the machine only if all protective and safety-oriented
equipment (protective structures such as a cabin or rollbar, removable
safety devices, for example) is installed and functional.
Check the machine for visible damage and defects.
In case of damage and/or unusual behavior, put the machine out of
operation immediately and secure it against restart.
Have all malfunctions jeopardizing the safety of the operator or other
persons immediately repaired by a Wacker Neuson service center.
Starting the engine of the machine
Start the engine only according to the Operator’s Manual.
Observe all warning lights and indicator lights.
Do not use any liquid or gaseous starting aids (ether or starting fuel, for
example).
Operating the machine
Start and operate the machine only with the seat belt fastened and only
from the place provided for this.
Put the machine into operation only if visibility is sufficient (have
another person guide you if necessary).
Operation on slopes:
- Travel/work only uphill or downhill.
- Avoid driving across a slope, observe the machine’s permissible
inclination (and of the trailer if necessary).
- Keep loads on the uphill side of the machine and as close as
possible to it.
- Keep attachments/work equipment close to the ground.
Adapt the travel speed to the circumstances (ground conditions,
weather conditions, for example).
There is increased danger when reversing the machine. Persons in the
blind spot of the machine cannot be seen by the operator.
- Ensure that nobody is in the danger zone when changing the travel
direction.
Never get on a moving machine and never jump off the machine.
BA 34903 * 1.0 * Sicherheit.fm 2-7
Safety 2
Machine travel on public roads/sites
The specific national driving license is required.
Observe the national regulations (road traffic regulations, for example)
during machine travel on public roads/sites.
Ensure that the machine is in compliance with the national regulations.
In order not to blind other motorists, using the existing work lights
during machine travel on public roads/site is prohibited.
When crossing underpasses, bridges, tunnels, for example, ensure
that the clearance height and width is sufficient.
The attachment fitted onto the machine must be certified for travel on
public roads/sites (see registration documents, for example).
The attachment fitted onto the machine must be empty and in transport
position.
The attachment fitted onto the machine must be equipped with the
mandatory lights and protective equipment.
Take measures against unintentional operation of the operating
hydraulics.
If the machine has different steering modes, ensure that the mandatory
steering mode is selected.
Stopping the engine of the machine
Stop the engine only according to the Operator’s Manual.
Before stopping the engine, lower the work equipment/attachment to
the ground.
Stopping and securing the machine
Unbuckle the seat belt only after stopping the engine.
Before leaving the machine, secure it to prevent it from rolling away
(parking brake, suitable wheel chocks, for example).
Remove the starting key and secure the machine against unauthorized
operation.
2-8 BA 34903 * 1.0 * Sicherheit.fm
2 Safety
2.5 Lifting gear applications
Requirements
Have loads fastened and the operator guided by a qualified person
having specific knowledge of lifting gear applications and the usual
hand signals.
The person giving instructions to the operator must stay in visual
contact with the operator when fastening, guiding or removing the load
(maintain visual contact).
If this not be possible, ask one more person with the same qualifica-
tions to guide.
The operator may not leave his seat as long as the load is raised.
Fastening, guiding and removing loads
Follow the applicable specific regulations for fastening, guiding and
removing a load.
Wear protective clothing and equipment when fastening, guiding and
removing loads (hard hat, safety glasses, protective gloves, safety
boots, for example).
Do not place lifting and fastening gear over sharp edges or rotating
parts. Loads must be fastened so as to prevent them from slipping or
falling.
Move loads only on horizontal, level and firm ground.
Move loads close to the ground.
In order to avoid oscillating movements of loads:
- Perform smooth, slow movements with the machine.
- Use cables to guide the load (do not use hands to guide).
- Bear in mind the weather conditions (wind force, for example).
- Keep a minimum safety distance from objects.
The operator may allow the load to be fastened and removed only if
the machine and its work equipment are not being moved.
Danger zones must not overlap with the work zones of other machines.
BA 34903 * 1.0 * Sicherheit.fm 2-9
Safety 2
Lifting gear applications
The machine must be certified for lifting gear applications.
Observe the national regulations for lifting gear applications.
Lifting gear applications are procedures involving raising, transporting
and lowering loads with the help of lifting and fastening gear.
The help of an accompanying person is necessary for fastening,
guiding and removing the load.
There must be nobody under the load.
Stop the machine immediately and stop the engine if persons enter the
danger zone.
Use the machine for lifting gear applications ONLY if the mandatory
lifting gear (joint rod and load hook, for example) and safety equipment
(optical and acoustic warning devices, hose burst valve, stability table,
for example) is installed and functional.
Use only lifting and fastening gear certified by a test/certification body,
observe the inspection intervals (Only use chains and shackles. No
belts, slings or cables).
Do not use any lifting and fastening gear that is dirty, damaged or not
of sufficient size.
Do not interrupt the work process with a load attached.
2-10 BA 34903 * 1.0 * Sicherheit.fm
2 Safety
2.6 Trailer operation
Trailer operation
The machine must be certified for trailer operation.
Observe the national regulations for trailer operation.
The specific national driving license is required.
Carrying passengers on/in trailers is PROHIBITED.
Observe the maximum permissible tongue load and towing capacity.
Do not exceed the permissible trailer speed.
Trailer operation with the towing gear of the machine is prohibited.
Trailer operation changes the machine’s operating behavior, the
operator must be familiar with this and act accordingly.
Bear in mind the machine’s steering mode and the trailer’s turning
circle.
Before hitching/unhitching the trailer, secure it to prevent it from rolling
away (parking brake, suitable wheel chocks, for example).
There must be nobody between the machine and the trailer when
hitching a trailer.
Hitch the trailer onto the machine correctly.
Ensure that all equipment works correctly (brakes, lights, for example).
Before starting machine travel, ensure that nobody is between the
machine and the trailer.
BA 34903 * 1.0 * Sicherheit.fm 2-11
Safety 2
2.7 Operation of attachments
Attachments
Use only attachments that are certified for the machine or its protective
equipment (shatter protection, for example).
All other attachments require the machine manufacturer’s release.
The danger zone and the work zone depend on the attachment used –
see the Operator’s Manual of the attachment.
Secure the load.
Do not overload attachments.
Check the correct position of the lock.
Operation
Carrying persons on/in an attachment is prohibited.
Installing a work platform is prohibited.
- Exception: The machine is certified and equipped with the necessary
safety equipment.
Attachments and counterweights modify handling, as well as the
steering and braking capability of the machine.
The operator must be familiar with these modifications and act accord-
ingly.
Before starting work, operate the attachment to check that it works
correctly.
Before putting the attachment into operation, ensure that nobody is in
danger.
Lower the attachment to the ground before leaving the operator seat.
Removing and fitting attachments
Before uncoupling or coupling hydraulic connections:
- Stop the engine
- Release the pressure in the operating hydraulics
Picking up and lowering attachments to the ground requires special
care:
- Pick up and safely lock the attachment in accordance with the
Operator’s Manual.
- Lower the attachment only to firm, level ground and secure it to
prevent it from tipping over or rolling away.
Put the machine and the attachment into operation only if:
- The protective equipment has been installed and is functional.
- The connections for the lights and the hydraulic system have been
established and are functional.
Perform a visual check of the lock after locking the attachment.
There must be nobody between the machine and the equipment when
picking up or lowering an attachment to the ground.
2-12 BA 34903 * 1.0 * Sicherheit.fm
2 Safety
2.8 Towing, loading and transporting
Towing
Seal off the danger zone.
Ensure that no one is near the towing bar or cable. The safety distance
is equal to 1.5 times the length of the towing equipment.
Observe the mandatory transport position, permissible speed and
itinerary.
A tractor vehicle of the same weight category must be used as a
minimum. Furthermore, the tractor vehicle must be equipped with a
safe braking system and sufficient tractive power.
Use only towing bars or cables certified by a test/certification body,
observe the inspection intervals.
Do not use any towing bars or cables that are dirty, damaged or not of
sufficient size.
Fasten towing bars or cables only at the defined points.
Tow away only in accordance with this Operator’s Manual to avoid
damage to the machine.
Observe the national regulations (light regulations, for example) when
towing on public roads/sites.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276

Wacker Neuson 5055 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI