Original operating instructions
Document number: 150001257_06_us
Version: 24/04/2023
BX201-32
Precision forage harvester
BiG X 580
From machine number: 1126759
2
BiG X 580
Original operating instructions 150001257_06_us
Contact
Krone North America, Inc.
12121 Forest Dr.
Olive Branch, MS 38654
U.S.A.
Phone + 1 662 913-7171
Fax + 1 662 913-7137
Email [email protected]
Internet www.krone-northamerica.com
For information on your KRONE machines, also refer to mykrone.green. After you have
registered, you can generate and manage your machines via the machine number so that you
can view the machine data. Via your personal account, you can also access all KRONE
Services.
Information for enquiries and orders
Model
Vehicle identification number
Year of manufacture
Contact data of your dealer
Table of contents
BiG X 580
Original operating instructions 150001257_06_us 3
1 Information on This Document...............................................................................................13
1.1 Validity .......................................................................................................................................13
1.2 Significance of the document.....................................................................................................13
1.3 Re-ordering ................................................................................................................................13
1.4 Applicable documents................................................................................................................13
1.5 Target group of this document ...................................................................................................13
1.6 How to use this document..........................................................................................................14
1.6.1 Directories and references.........................................................................................................14
1.6.2 Information on direction .............................................................................................................14
1.6.3 Term “machine”..........................................................................................................................14
1.6.4 Figures .......................................................................................................................................14
1.6.5 Scope of the document ..............................................................................................................14
1.6.6 Means of representation ............................................................................................................14
1.6.7 Conversion table ........................................................................................................................17
2 Safety ........................................................................................................................................18
2.1 Intended use ..............................................................................................................................18
2.2 Reasonably foreseeable misuse................................................................................................18
2.3 Service life of the machine.........................................................................................................19
2.4 Basic safety instructions ............................................................................................................19
2.4.1 Importance of operating instructions..........................................................................................19
2.4.2 Personnel qualification of the operating personnel ....................................................................19
2.4.3 Personnel qualification of the technicians..................................................................................20
2.4.4 Children in danger......................................................................................................................20
2.4.5 Connecting the machine ............................................................................................................20
2.4.6 Structural modifications on the machine ....................................................................................21
2.4.7 Additional equipment and spare parts .......................................................................................21
2.4.8 Jobs on the machine..................................................................................................................21
2.4.9 Operational safety: Technically sound condition........................................................................22
2.4.10 Danger zones.............................................................................................................................23
2.4.11 Ensuring functionality of safety devices .....................................................................................25
2.4.12 Personal protective equipment ..................................................................................................25
2.4.13 Safety sign on the machine........................................................................................................26
2.4.14 Road safety................................................................................................................................26
2.4.15 Parking the machine safely .......................................................................................................27
2.4.16 Consumables .............................................................................................................................27
2.4.17 Chemicals ..................................................................................................................................28
2.4.18 Dangers arising from environment.............................................................................................28
2.4.19 Sources of danger on the machine ............................................................................................30
2.4.20 Dangers in connection with certain activities: climbing up and down ........................................31
2.4.21 Dangers in connection with certain activities: Working on the machine ....................................32
2.4.22 Dangers in connection with certain activities: checking and charging batteries ........................33
2.4.23 Dangers in connection with certain activities: working on wheels and tyres..............................33
2.4.24 Behaviour in dangerous situations and in case of accidents .....................................................34
2.5 Safety routines ...........................................................................................................................34
2.5.1 Shutting down and safeguarding the machine...........................................................................34
2.5.2 Securing raised machine and machine parts against lowering..................................................35
2.5.3 Carrying out oil level check and oil and filter element changes safely.......................................35
2.5.4 Running actuator test.................................................................................................................36
2.6 Safety sign on the machine........................................................................................................36
2.7 Information signs on the machine ..............................................................................................59
2.8 Safety equipment .......................................................................................................................67
2.8.1 SMV emblem .............................................................................................................................69
2.8.2 Fire extinguisher ........................................................................................................................69
3 Data memory ............................................................................................................................71
4 Machine Description................................................................................................................72
4.1 Machine overview ......................................................................................................................72
4.1.1 Contents of the storage compartment........................................................................................73
4.2 Labelling.....................................................................................................................................74
4.3 EPA certificate on the engine.....................................................................................................75
Table of contents
4
BiG X 580
Original operating instructions 150001257_06_us
4.4 Lighting ......................................................................................................................................75
4.4.1 Road travel lighting ....................................................................................................................75
4.4.2 Working lights ............................................................................................................................76
4.4.3 Maintenance lighting ..................................................................................................................77
4.5 Function description chopping crops .........................................................................................78
5 Technical Data..........................................................................................................................80
5.1 Dimensions ................................................................................................................................80
5.2 Technically permitted maximum speed (road travel) .................................................................80
5.3 Engine data................................................................................................................................81
5.4 Traction drive .............................................................................................................................81
5.5 Electrical system ........................................................................................................................81
5.6 Airborne noise emission.............................................................................................................81
5.7 Ambient temperature .................................................................................................................82
5.8 Vibration values .........................................................................................................................82
5.9 tow coupling ...............................................................................................................................82
5.10 Power supply for headers – power ............................................................................................82
5.11 Power supply for headers – hydraulics ......................................................................................82
5.12 Power supply for headers – electrics .........................................................................................82
5.13 Consumables .............................................................................................................................82
5.13.1 Oils.............................................................................................................................................83
5.13.2 Lubricating grease .....................................................................................................................85
5.13.3 Coolant.......................................................................................................................................85
5.13.4 Refrigerant (air conditioning)......................................................................................................85
5.13.5 Fuel/urea....................................................................................................................................86
5.14 Tyres ..........................................................................................................................................86
5.15 Total weights and axle loads......................................................................................................87
5.16 Released headers......................................................................................................................90
6 Control and Display Elements ................................................................................................92
6.1 Overview of operating elements ................................................................................................92
6.2 Opening doors and windows of cabin .......................................................................................92
6.3 Control and display elements on the steering column ...............................................................95
6.3.1 Steering column switch ..............................................................................................................95
6.3.1.1 Activating horn ...........................................................................................................................95
6.3.1.2 Switching direction indicators on/off...........................................................................................96
6.3.1.3 Switching parking light, dipped beam and work lightings on/off.................................................96
6.3.1.4 Switching full beam on/off ..........................................................................................................98
6.3.1.5 Actuating headlamp flasher .......................................................................................................98
6.3.1.6 Switching windshield wipers on/off ...........................................................................................98
6.3.2 Indicator and warning lamps ......................................................................................................99
6.3.3 Switching the flashing warning light on/off ...............................................................................100
6.4 Actuating service brake............................................................................................................100
6.5 Actuate the trailer brake system (for "trailer brake system" version) .......................................101
6.6 Actuating the momentary foot switches (for "Momentary foot switches in the cabin" version) 102
6.7 Mirror adjuster..........................................................................................................................102
6.8 Setting the anti-collision mirror.................................................................................................103
6.9 Keypad for wiper and warning beacon.....................................................................................104
6.10 Lighting on the cabin ladder and right ladder...........................................................................104
6.11 Interior lighting .........................................................................................................................106
6.12 Operating elements on control lever ........................................................................................106
6.13 Control and display elements on the keypad ...........................................................................110
6.14 Main mode switch ....................................................................................................................112
6.15 Quick-stop switch.....................................................................................................................113
6.16 Navigation module ...................................................................................................................113
6.17 Ignition lock ..............................................................................................................................115
6.18 Additional keypad.....................................................................................................................115
6.19 Sockets ....................................................................................................................................116
6.19.1 Cigarette lighter 12 Volt ...........................................................................................................116
6.19.2 12 V socket/24 V socket ..........................................................................................................117
6.19.3 Diagnostics sockets .................................................................................................................118
6.19.4 In-cab socket............................................................................................................................118
Table of contents
BiG X 580
Original operating instructions 150001257_06_us 5
6.19.5 USB connection .......................................................................................................................118
6.20 Grinding control unit.................................................................................................................119
6.21 Quick-stop switch grinding control unit ....................................................................................120
6.22 Opening and closing side hoods and rear hood ......................................................................121
7 Initial operation ......................................................................................................................122
7.1 Checklist for initial operation ....................................................................................................122
7.2 Mounting warning panels in operating position........................................................................123
7.3 Mounting fire extinguisher........................................................................................................123
7.4 Mounting licence plate .............................................................................................................124
8 Start-up ...................................................................................................................................125
8.1 Check before start-up ..............................................................................................................125
8.2 Setting driver’s seat .................................................................................................................126
8.2.1 Air-cushioned comfort seat ......................................................................................................126
8.2.1.1 Operating air-cushioned comfort seat (for "Standard" version)................................................127
8.2.1.2 Operating air-cushioned comfort seat (for "ACTIVO" version).................................................129
8.2.1.3 Turning the driver's seat (for the "Swivel seat adapter" design) ..............................................133
8.2.2 Steering column adjustment ....................................................................................................133
8.2.3 Setting the terminal ..................................................................................................................134
8.2.4 Monitor for camera monitoring .................................................................................................135
8.2.5 Sun visor ..................................................................................................................................136
8.2.6 Adjustable air nozzles ..............................................................................................................137
8.2.7 Inside rear mirror......................................................................................................................137
8.3 General aspects.......................................................................................................................137
8.3.1 Instructional seat......................................................................................................................137
8.3.2 Cooling box (version with "Insulated thermobox")....................................................................138
8.3.3 Drawer for first-aid kit and operating instructions.....................................................................138
9 Start-up – Grass mode/direct cut header ............................................................................139
9.1 Removing the corn conditioner ................................................................................................140
9.2 Installing the grass channel .....................................................................................................144
9.3 Adjusting the air intake.............................................................................................................145
9.4 Removing round brush from the rotating screen......................................................................146
9.5 Setting Lifting Unit Hydraulics ..................................................................................................146
9.6 Removing grain capture sheet .................................................................................................147
9.7 Removing spout extension.......................................................................................................148
9.8 Mounting camera in grass mode position (for "EasyLoad auto-loading system" version) .......150
9.9 Dismounting camera in maize mode position (for "EasyLoad auto-loading system" version) .151
9.10 Removing rear weight ..............................................................................................................152
9.11 Removing husk comb (version with "Husk comb")...................................................................154
9.11.1 Removing the maintenance flap and deflector sheet...............................................................154
9.11.2 Removing blade support and husk comb.................................................................................156
9.11.3 Removing wear plate ...............................................................................................................157
9.11.4 Mounting wear plate (without window) and deflector sheet .....................................................157
9.11.5 Mounting maintenance flap transfer shaft................................................................................158
9.12 Removing additional axle.........................................................................................................158
10 Commissioning – Maize mode..............................................................................................166
10.1 Removing the grass channel ...................................................................................................167
10.2 Installing the corn conditioner ..................................................................................................168
10.3 Adjusting the air intake.............................................................................................................172
10.4 Pressing round brushes onto the rotating screen ....................................................................173
10.5 Adjusting the lifting unit hydraulics...........................................................................................174
10.6 Mounting grain capture sheet ..................................................................................................174
10.7 Mounting spout extension ........................................................................................................175
10.8 Mounting camera in maize mode position (for "EasyLoad auto-loading system" version) ......180
10.9 Dismounting camera in grass mode position (for "EasyLoad auto-loading system" version) ..182
10.10 Attaching rear weight ...............................................................................................................182
10.11 Installing husk comb (version with "Husk comb").....................................................................185
10.11.1 Removing the maintenance flap transfer shaft and wear plate................................................185
10.11.2 Mounting wear plate.................................................................................................................187
Table of contents
6
BiG X 580
Original operating instructions 150001257_06_us
10.11.3 Mounting husk comb................................................................................................................188
10.11.4 Mounting blade support ...........................................................................................................189
10.11.5 Mounting maintenance flap transfer shaft and deflector sheet ................................................191
10.12 Mounting additional axle ..........................................................................................................192
11 Commissioning – Grass/maize mode for the transition period.........................................202
12 Start-up – Attaching and removing EasyFlow ....................................................................206
12.1 Mounting EasyFlow..................................................................................................................207
12.1.1 Preparing the intake.................................................................................................................207
12.1.2 Connecting EasyFlow ..............................................................................................................208
12.1.3 Connecting hydraulic hoses.....................................................................................................210
12.1.4 Moving parking jacks on right/left into transport position .........................................................211
12.2 Removing EasyFlow ................................................................................................................211
12.3 Putting Down EasyFlow ...........................................................................................................213
13 Commissioning – Attaching and removing XCollect..........................................................214
13.1 Attaching XCollect....................................................................................................................215
13.1.1 Preparing the intake.................................................................................................................215
13.1.2 Connecting XCollect ................................................................................................................216
13.1.3 Connecting hydraulic hoses.....................................................................................................218
13.1.4 Moving support jacks on right/left into transport position .........................................................219
13.1.5 Enabling additional axle on the terminal ..................................................................................220
13.2 Removing XCollect ..................................................................................................................220
13.3 Parking XCollect ......................................................................................................................223
14 Start-up – Attaching and removing EasyCollect.................................................................224
14.1 Mounting EasyCollect ..............................................................................................................225
14.1.1 Preparing the intake.................................................................................................................225
14.1.2 Connecting EasyCollect...........................................................................................................226
14.1.3 Connecting hydraulic hoses.....................................................................................................228
14.1.4 Moving parking jacks on right/left into transport position .........................................................229
14.2 Removing EasyCollect.............................................................................................................230
14.3 Putting down EasyCollect .......................................................................................................233
15 Start-up – Attaching and removing XDisc ...........................................................................234
15.1 Mounting XDisc........................................................................................................................235
15.1.1 Preparing the intake.................................................................................................................235
15.1.2 Connecting XDisc ....................................................................................................................235
15.1.3 Moving parking jacks on right/left into transport position .........................................................238
15.2 Removing XDisc ......................................................................................................................238
15.3 Putting down XDisc..................................................................................................................240
16 Driving and Transport ...........................................................................................................241
16.1 Preparing the machine for road travel......................................................................................241
16.1.1 Transport position ....................................................................................................................242
16.1.2 Moving header to transport position.........................................................................................242
16.1.3 Moving intake into transport position .......................................................................................245
16.1.4 Swivelling spout into transport position....................................................................................245
16.1.5 Opening the stop cock additional running gear on the XCollect ..............................................246
16.2 Starting engine.........................................................................................................................246
16.2.1 Observing indicator and warning lamps...................................................................................248
16.3 Behaviour after the engine has stalled.....................................................................................249
16.4 Starting up machine .................................................................................................................249
16.4.1 Setting the acceleration behaviour...........................................................................................250
16.4.2 Notes on driving the machine ..................................................................................................250
16.4.3 Driving forwards and stopping .................................................................................................251
16.4.3.1 Cruise control...........................................................................................................................251
16.4.4 Driving backward and stopping................................................................................................253
16.5 Stopping the machine ..............................................................................................................253
16.5.1 Stopping machine by using control lever .................................................................................254
16.5.2 Stopping machine with the service brake ................................................................................255
16.6 Couple brake pedals (for "trailer brake system" version).........................................................256
Table of contents
BiG X 580
Original operating instructions 150001257_06_us 7
16.7 Applying parking brake ............................................................................................................256
16.8 Switching off the engine...........................................................................................................258
16.9 Fitting wheel chocks.................................................................................................................258
16.10 Main battery switch ..................................................................................................................259
16.11 Parking the machine ................................................................................................................259
16.12 Towing the machine.................................................................................................................260
16.12.1 Releasing the parking brake manually.....................................................................................261
16.13 Preparing the machine for shipment ........................................................................................262
16.13.1 Lashing the machine................................................................................................................262
16.13.2 Removing the machine wheels ................................................................................................263
17 Operation device....................................................................................................................264
17.1 Raising and lowering lifting unit ...............................................................................................265
17.2 Aligning pendulum tube horizontally ........................................................................................265
17.3 Releasing header locking.........................................................................................................266
17.4 Trailer operation.......................................................................................................................267
17.4.1 Connecting trailer.....................................................................................................................268
17.4.2 Disconnecting trailer ................................................................................................................269
17.5 Additional axles........................................................................................................................270
17.5.1 Maize mode .............................................................................................................................271
17.5.2 Grass mode .............................................................................................................................271
17.5.3 XDisc operating mode..............................................................................................................271
17.6 Silage additives unit .................................................................................................................272
17.6.1 Internal silage additives unit coarse dosing (for version with "Controlled silage additives unit")
.................................................................................................................................................272
17.6.2 Internal silage additives unit fine dosing (for "regulated silage additives unit fine dosing" version)
.................................................................................................................................................278
17.6.3 Connecting an additional silage additives unit (for "External silage additives unit" version)....284
17.7 Field mode on slopes...............................................................................................................284
17.8 Setting inclination-dependent distribution of traction of the traction drive (for "inclination sensor"
version) ....................................................................................................................................285
17.9 Fast change of direction of travel (fast reversing)....................................................................285
17.10 Operating intake/header ..........................................................................................................286
17.11 Lifting unit control.....................................................................................................................288
17.12 Setting spout ...........................................................................................................................291
17.13 Adjusting discharge distance ...................................................................................................292
17.14 TractionControl/Traction control system ..................................................................................292
17.15 Automatic steering system.......................................................................................................293
17.16 Setting chop length ..................................................................................................................295
17.17 Metal detection.........................................................................................................................297
17.18 RockProtect .............................................................................................................................298
17.19 ConstantPower ........................................................................................................................299
17.20 Engine speed management .....................................................................................................300
17.21 AutoScan .................................................................................................................................301
17.22 CropControl..............................................................................................................................301
17.23 PowerSplit................................................................................................................................303
17.24 Contents sensor system ..........................................................................................................305
17.25 Operating VariQuick electrically...............................................................................................307
17.26 Operating VariLOC chop length gearbox.................................................................................308
17.26.1 Switching VariLOC cutting length gearbox ..............................................................................310
17.26.2 VariLOC cutting length gearbox settings on the terminal.........................................................311
17.27 Operating the EasyLoad auto-loading system .........................................................................314
17.27.1 Camera monitor status display ................................................................................................314
17.27.2 Setting EasyLoad auto-loading system....................................................................................316
17.27.3 Activating/deactivating EasyLoad auto-loading system ...........................................................319
17.27.4 Selecting filling strategy ...........................................................................................................319
17.27.5 Filling to rear ............................................................................................................................320
17.28 Operating the dirt seal..............................................................................................................321
18 Terminal ..................................................................................................................................323
18.1 Display design..........................................................................................................................323
18.2 Description display...................................................................................................................324
Table of contents
8
BiG X 580
Original operating instructions 150001257_06_us
18.3 Possible terminals....................................................................................................................324
18.4 Input window ............................................................................................................................325
18.5 Selection window .....................................................................................................................326
19 Terminal machine functions .................................................................................................328
19.1 Status line ................................................................................................................................329
19.2 Malfunctions indicated on malfunction warning panel..............................................................334
19.2.1 Warning lamps – urea tank filling level ....................................................................................336
19.2.2 Warning lamps – urea quality ..................................................................................................336
19.2.3 Warning lamps – urea system defective or tampered with ......................................................337
19.2.4 Warning lamps – load condition diesel particulate filter ...........................................................339
19.3 Keys in the title bar ..................................................................................................................340
19.3.1 “Counters” menu ......................................................................................................................340
19.3.2 “Error” menu.............................................................................................................................350
19.3.3 Main menu ...............................................................................................................................354
19.4 Direct input “Field mode”..........................................................................................................354
19.4.1 Temporarily change working width or number of rows ............................................................355
19.4.2 Changing the header speed.....................................................................................................356
19.4.3 Change chop length.................................................................................................................356
19.4.4 Changing the lifting unit control default value ..........................................................................357
19.4.5 Changing Corn Conditioner Roller Distance ............................................................................357
19.5 Information area.......................................................................................................................358
19.6 Engine and driving data display range.....................................................................................358
19.7 Displaying malfunctions in the "Engine and driving data" display range..................................363
19.8 Traction drive indicator lights ...................................................................................................363
20 Terminal - Menus ...................................................................................................................366
20.1 Menu structure .........................................................................................................................366
20.2 Bringing up menu level ............................................................................................................376
20.3 Navigating in menus ................................................................................................................377
20.3.1 Changing/saving parameter.....................................................................................................377
20.4 “Diagnostics” menu explanation...............................................................................................377
20.5 "Machine" menu.......................................................................................................................379
20.5.1 "Electronics" menu...................................................................................................................381
20.5.1.1 "E-Solutions" menu ..................................................................................................................382
20.5.1.2 "Telemetry" menu.....................................................................................................................382
20.5.1.3 "Active errors" menu ................................................................................................................384
20.5.1.4 "Error history" menu.................................................................................................................385
20.5.1.5 "Control units overview" menu .................................................................................................386
20.5.1.6 "Control unit versions" menu....................................................................................................388
20.5.1.7 "Information" menu...................................................................................................................389
20.5.2 "Lighting" menu........................................................................................................................389
20.5.3 "Camera systems" menu..........................................................................................................391
20.5.3.1 "Camera system" menu ...........................................................................................................392
20.5.3.2 "Surround View" menu.............................................................................................................392
20.6 “Cabin” menu ...........................................................................................................................393
20.6.1 “Terminal” menu.......................................................................................................................395
20.6.2 “Armrest” menu ........................................................................................................................396
20.6.3 “Control Lever” menu ...............................................................................................................398
20.6.4 "Interior lighting" menu.............................................................................................................399
20.6.5 “Control Unit Versions” menu...................................................................................................400
20.6.6 “Printer” menu ..........................................................................................................................401
20.6.7 "Automatic climate control" menu ............................................................................................401
20.6.8 "Wiper" menu ...........................................................................................................................403
20.6.9 "Mirror heating" menu ..............................................................................................................404
20.6.10 "Momentary foot switch" menu.................................................................................................404
20.7 "Lubrication" menu...................................................................................................................405
20.7.1 "Central lubrication" menu........................................................................................................406
20.7.2 "Intermediate gearbox" menu...................................................................................................408
20.8 "Crop flow" menu .....................................................................................................................408
20.8.1 “Header” menu.........................................................................................................................412
20.8.2 “Header Drive” menu ...............................................................................................................412
Table of contents
BiG X 580
Original operating instructions 150001257_06_us 9
20.8.3 "AutoScan" menu.....................................................................................................................413
20.8.4 “Intake” menu...........................................................................................................................414
20.8.5 "Foreign object detection" menu ..............................................................................................414
20.8.6 “Lifting Unit” menu....................................................................................................................415
20.8.7 "Grinding device and counterblade" menu...............................................................................416
20.8.8 “Main Coupling” menu..............................................................................................................419
20.8.9 “Corn Conditioner” menu .........................................................................................................420
20.8.10 “Discharge Accelerator” menu .................................................................................................423
20.8.11 "Content material sensor" menu ..............................................................................................424
20.8.12 "CropControl" menu .................................................................................................................425
20.8.13 "Silage additives units" menu...................................................................................................428
20.8.13.1 "External silage additives unit" menu.......................................................................................428
20.8.13.2 "Silage additives unit fine dosing" menu ..................................................................................428
20.8.13.3 "Silage additives unit coarse dosing" menu .............................................................................429
20.9 "Spout" menu ...........................................................................................................................430
20.9.1 "Spout" menu ...........................................................................................................................431
20.9.2 "Auto-loading system" menu....................................................................................................433
20.10 “Engine” menu .........................................................................................................................434
20.10.1 “Diesel Engine” menu ..............................................................................................................434
20.10.2 “ConstantPower” menu ...........................................................................................................436
20.10.3 "Compressed air cleaning" menu.............................................................................................437
20.11 “Hydraulics” menu....................................................................................................................438
20.11.1 “Header Locking” menu ..........................................................................................................439
20.11.2 “Work Hydraulics” menu ..........................................................................................................439
20.11.3 “Auxiliary Hydraulics” menu .....................................................................................................440
20.12 “Drive Functions” menu............................................................................................................440
20.12.1 “Automatic Steering System” menu .........................................................................................442
20.12.2 “Traction Drive” Menu ..............................................................................................................442
20.12.3 “Additional Axle” menu.............................................................................................................445
20.12.4 “Rear Axle” menu.....................................................................................................................445
20.12.5 "Trailer brake" menu ................................................................................................................447
20.13 “Season Settings” menu ..........................................................................................................447
20.14 "User level" menu.....................................................................................................................448
21 Settings...................................................................................................................................449
21.1 Optimising crop flow.................................................................................................................449
21.2 Optimising discharge capacity of the machine.........................................................................450
21.2.1 Adjusting overhang of chopping blades ...................................................................................450
21.2.2 Setting drum base ...................................................................................................................450
21.2.3 Setting the rear wall of the discharge accelerator....................................................................453
21.3 Setting the corn conditioner/grass channel holding-down clamp.............................................458
21.4 Setting deflector sheet on the corn conditioner........................................................................458
22 Maintenance - General Information......................................................................................460
22.1 Observe the service record booklet .........................................................................................460
22.2 Maintenance table....................................................................................................................461
22.2.1 Maintenance – Before the season ...........................................................................................461
22.2.2 Maintenance – After the season ..............................................................................................462
22.2.3 Maintenance - once after 1 hour .............................................................................................463
22.2.4 Maintenance - once after 4 hours ............................................................................................464
22.2.5 Maintenance - once after 10 hours ..........................................................................................464
22.2.6 Maintenance – 6 times after every 10 hours............................................................................464
22.2.7 Maintenance - Once after 50 hours .........................................................................................464
22.2.8 Maintenance – Once after 200 hours.......................................................................................465
22.2.9 Maintenance – Once after 1,000 km........................................................................................465
22.2.10 Maintenance - Every 10 hours, but at least once a day...........................................................465
22.2.11 Maintenance – Weekly.............................................................................................................467
22.2.12 Maintenance – Every 30 hours ................................................................................................467
22.2.13 Maintenance - Every 50 hours .................................................................................................467
22.2.14 Maintenance - every 100 hours ...............................................................................................467
22.2.15 Maintenance - every 250 hours ...............................................................................................468
22.2.16 Maintenance - Every 500 hours ...............................................................................................468
Table of contents
10
BiG X 580
Original operating instructions 150001257_06_us
22.2.17 Maintenance - Every 750 hours, at least every 2 years...........................................................470
22.2.18 Maintenance - every 1,000 hours but at least at the end of the season ..................................470
22.2.19 Maintenance – Every 3000 hours ............................................................................................470
22.2.20 Maintenance - every 3 years....................................................................................................470
22.2.21 Maintenance - as required .......................................................................................................471
22.3 Tightening torques ...................................................................................................................472
22.4 Cleaning the machine ..............................................................................................................475
22.5 Compressed air connections to clean with compressed air.....................................................476
23 Maintenance - Engine ............................................................................................................478
23.1 Engine overview ......................................................................................................................479
23.2 Dirt deposits in engine compartment .......................................................................................479
23.2.1 Cleaning engine compartment with compressed air ................................................................480
23.3 Engine oil level.........................................................................................................................480
23.3.1 Checking engine oil level ........................................................................................................481
23.3.2 Topping up engine oil...............................................................................................................481
23.4 Fuel prefilter/water separator ...................................................................................................482
23.4.1 Changing the fuel filter element ...............................................................................................482
23.4.2 Cleaning the fuel prefilter sight glass .......................................................................................483
23.4.3 Draining condensation water out of the fuel prefilter................................................................483
23.5 Changing urea filter inserts ......................................................................................................484
23.6 Cleaning the non-return valve on the urea pump module........................................................486
23.7 Refuelling .................................................................................................................................488
23.8 Topping up urea solution .........................................................................................................489
23.9 Vent fuel filter ...........................................................................................................................490
23.10 Engine coolant .........................................................................................................................491
23.11 Checking the engine coolant level ...........................................................................................492
23.12 Checking engine piping............................................................................................................493
23.12.1 Checking pipework in the air conditioning and heating system ...............................................493
23.12.2 Checking tubing in engine cooling system...............................................................................494
23.12.3 Checking pipework in air intake and charge air .......................................................................494
23.12.4 Checking fuel lines...................................................................................................................495
23.13 Cleaning air filter ......................................................................................................................495
23.14 Replacing safety cartridge .......................................................................................................496
23.15 Shutting down the diesel engine ..............................................................................................497
24 Maintenance – Compressed Air System..............................................................................498
24.1 Drain condensation water from the compressed air tank.........................................................498
24.2 Retighten tensioning straps at the compressed air tank ..........................................................499
25 Maintenance – Basic Machine ..............................................................................................500
25.1 Cleaning the windows and outside rear-view mirrors of the cabin...........................................500
25.2 Checking/refilling windscreen washer system .........................................................................501
25.3 Maintaining air conditioning and heating..................................................................................502
25.3.1 Components of air conditioning ...............................................................................................502
25.3.2 Carrying out a visual inspection at the receiver/dryer ..............................................................503
25.3.3 Checking the condition and filling quantity of refrigerant ........................................................503
25.3.4 Replacing/cleaning fresh air filter.............................................................................................504
25.3.5 Replacing/cleaning circulation filter..........................................................................................505
25.4 Cleaning cooler and cooler compartment ................................................................................505
25.5 Draining coolant .......................................................................................................................506
25.6 Maintaining chassis..................................................................................................................507
25.6.1 Checking attachment of steering cylinder ................................................................................507
25.6.2 Checking fitting of track rod .....................................................................................................507
25.6.3 Checking the hub cover of the rear axle, with front wheel drive version..................................508
25.6.4 Checking the hub bearing of the rear axle, for the front-wheel drive version...........................508
25.6.5 Checking attachment of wheel hub gearbox............................................................................509
25.7 Maintaining brake (Bosch) .......................................................................................................510
25.8 Maintaining belt drives ............................................................................................................511
25.8.1 Checking kraftband ..................................................................................................................512
25.8.2 Checking pulley........................................................................................................................513
25.9 Maintaining tyres and wheels...................................................................................................513
Table of contents
BiG X 580
Original operating instructions 150001257_06_us 11
25.9.1 Checking/maintaining tyres......................................................................................................513
25.9.2 Retighten wheel nuts ...............................................................................................................514
25.9.3 Running direction of tyres ........................................................................................................514
25.9.4 Changing tyre size ...................................................................................................................514
25.10 Maintaining tow coupling..........................................................................................................515
25.11 Checking the fire extinguisher..................................................................................................516
25.12 Checking the gaps at the mudguards ......................................................................................516
26 Maintenance – Feed System .................................................................................................519
26.1 Removing intake unit with mounting cart .................................................................................519
26.2 Mounting intake unit with installation cart ................................................................................522
26.3 Removing intake unit with header............................................................................................524
26.4 Mounting intake unit with header .............................................................................................526
26.5 Grinding chopping blades ........................................................................................................528
26.5.1 Grinding the chopping blades when intake is not mounted .....................................................530
26.5.2 Checking the grinding stone and cleaning the grinding channel..............................................531
26.5.3 Performing grinding process ....................................................................................................532
26.5.4 Readjusting the counterblade ..................................................................................................533
26.5.5 Grinding and readjusting counterblade (for the version with "automatisch counterblade
adjustment") .............................................................................................................................536
26.6 Readjusting or replacing grinding stone...................................................................................537
26.6.1 Checking grinding stone ..........................................................................................................538
26.6.2 Readjusting grinding stone ......................................................................................................539
26.6.3 Replacing grinding stone .........................................................................................................541
26.7 Readjusting or changing chopping blades ...............................................................................543
26.8 Working with half the number of chopping blades ...................................................................558
26.9 Turning or replacing counterblade ...........................................................................................559
26.10 Operating the mounting cart of the chopper unit (for "Chopper unit mounting cart" design) ...561
26.10.1 Setting mounting cart ...............................................................................................................561
26.10.2 Parking mounting cart ..............................................................................................................562
26.11 Turning or replacing conveyor bars of pre-compression roller.................................................562
26.12 Changing conveyor bars on feed roller ....................................................................................563
26.13 Adjusting the distance between the scraper and flat roller ......................................................563
26.14 Setting the gap compression roller-scraper .............................................................................565
26.15 Setting the tension springs of intake unit .................................................................................567
27 Maintenance - Crop Flow.......................................................................................................569
27.1 Access points to crop flow .......................................................................................................569
27.1.1 Removing the grass channel ...................................................................................................570
27.1.2 Installing the grass channel .....................................................................................................570
27.1.3 Opening maintenance flap transfer shaft .................................................................................570
27.1.4 Removing drum base and grating base (version with "Grating base").....................................571
27.1.5 Mounting drum base and grating base (version with "Grating base")......................................573
27.1.6 Removing the rear wall of the discharge accelerator...............................................................574
27.1.7 Reinstalling the rear wall of the discharge accelerator ............................................................575
27.1.8 Removing maintenance flap in channel support ......................................................................575
27.1.9 Opening maintenance flap in the spout ...................................................................................576
27.2 Maintaining the corn conditioner ..............................................................................................577
27.2.1 Lubricating the deflection roll of the corn conditioner belt after washing .................................577
27.2.2 Check the corn conditioner with rollers for wear and tear........................................................578
27.3 Maintenance discharge accelerator .........................................................................................579
27.3.1 Cleaning the bearing of the discharge accelerator ..................................................................579
27.3.2 Checking discharge scoops ....................................................................................................580
27.3.3 Removing/installing discharge scoops.....................................................................................580
27.3.4 Checking and adjusting discharge accelerator scraper ...........................................................581
27.4 Setting corn conditioner ...........................................................................................................582
27.5 Maintenance husk comb (version with "Husk comb") ..............................................................583
28 Maintenance - Hydraulic System..........................................................................................586
28.1 Pressure limiting valves ...........................................................................................................586
28.2 Hydraulic oil .............................................................................................................................587
28.3 Maintaining hydraulic oil tank...................................................................................................587
Table of contents
12
BiG X 580
Original operating instructions 150001257_06_us
28.4 Changing the high-pressure filter.............................................................................................588
28.5 Checking hydraulic hoses ........................................................................................................589
29 Maintenance - Gearbox .........................................................................................................590
29.1 Overview of gearboxes ............................................................................................................590
29.2 Maintaining transfer gearbox ...................................................................................................591
29.3 Maintaining intermediate gearbox............................................................................................592
29.4 Maintaining intermediate gearbox intake .................................................................................592
29.5 Maintaining bottom roller gearbox............................................................................................593
29.6 Maintaining top roller gearbox..................................................................................................594
29.7 Maintaining wheel hub gearbox ...............................................................................................595
29.8 Maintaining spout rotary drive gearbox....................................................................................598
29.9 Maintaining fan gearbox...........................................................................................................599
29.10 Maintaining power take-off gear...............................................................................................600
29.11 Servicing VariLOC chop length gearbox..................................................................................601
30 Maintenance – Electrics ........................................................................................................603
30.1 Batteries...................................................................................................................................604
30.1.1 Cleaning and maintaining batteries..........................................................................................605
30.1.2 Charging batteries....................................................................................................................605
30.1.3 Replacing batteries .................................................................................................................606
30.2 Maintaining alternator ..............................................................................................................608
30.3 Maintaining starter ...................................................................................................................609
31 Maintenance - Lubrication ....................................................................................................610
31.1 Lubricating universal shafts .....................................................................................................610
31.1.1 Lubricating the universal shaft drive intake..............................................................................611
31.1.2 Lubricating the universal shaft upper roller gearbox ................................................................611
31.1.3 Lubricating universal shaft header ...........................................................................................612
31.1.4 Lubricating the double joint ......................................................................................................613
31.2 Lubrication chart - machine......................................................................................................613
32 Maintenance – Central Lubrication System .......................................................................622
32.1 Distributor blocks of the central lubrication unit .......................................................................622
32.2 Lubricants ................................................................................................................................627
32.3 Filling the lubricant tank ...........................................................................................................627
32.4 Check filling level .....................................................................................................................628
32.5 Starting intermediate lubrication ..............................................................................................629
33 Malfunction, cause and remedy ...........................................................................................630
33.1 Electrics/electronics BiG X defective .......................................................................................630
33.1.1 Cable break, short circuit .........................................................................................................630
33.1.2 Overview of fuses ....................................................................................................................632
33.1.3 Overview of control units..........................................................................................................635
33.1.4 Overview of sensors ................................................................................................................636
33.1.5 Overview actuators ..................................................................................................................637
33.2 Malfunctions in the central lubrication unit ...............................................................................639
33.2.1 Searching for the error in the central lubrication system..........................................................639
33.3 External starting of the machine ..............................................................................................639
33.4 Removing crop blockages in area of crop flow ........................................................................641
33.5 Car jack contact points.............................................................................................................646
34 Waste disposal.......................................................................................................................648
Index........................................................................................................................................649
Information on This Document 1
Validity 1.1
BiG X 580
Original operating instructions 150001257_06_us 13
1 Information on This Document
1.1 Validity
This document is valid for machines of type:
BX201-32 (BiG X 580)
All information, illustrations and technical data in this document correspond to the latest state at
the time of publication.
We reserve the right to make design changes at any time and without notification of reasons.
1.2 Significance of the document
This is an important document. It is addressed to the user and contains safety-relevant
information.
Prior to starting work, read the complete document and observe its contents.
Keep this document ready to hand for the user of the machine.
Hand over this document to subsequent users.
1.3 Re-ordering
You can request a replacement document if this document became completely or partly
unusable, or if you need it in a different language. Please specify the document number shown
on the cover page in your order. Alternatively, you can download the document online from
KRONE MEDIA https://media.mykrone.green.
1.4 Applicable documents
To ensure that the machine is used safely and as intended, observe the following further
applicable documents.
• Operating instructions for diesel engine, MTU Friedrichshafen GmbH
• Fuel specification for diesel engine, MTU Friedrichshafen GmbH
• Maintenance instructions for diesel engine, MTU Friedrichshafen GmbH
• Supplement to operating instructions "Error messages, information messages and
parameters"
• Operating instructions for prefilter for diesel fuel, HYDAC
• Operating instructions for header, KRONE
• Operating instructions for transport wagon, KRONE
• KRONE NIR Control dual operating instructions
• Operating instructions for universal shaft
• Circuit diagram, KRONE
• Spare parts list, KRONE
• Service record booklet, KRONE
1.5 Target group of this document
This document aims at the operator of the machine who fulfills the minimum requirements of
personnel qualification,see Page19.
1 Information on This Document
1.6 How to use this document
14
BiG X 580
Original operating instructions 150001257_06_us
1.6 How to use this document
1.6.1 Directories and references
Contents/headers
The contents and headers in this document ensure quick orientation in the chapters.
Index
The index contains catchwords in alphabetical order which enable to find information on a
desired topic easily. The index can be found on the last pages of this document.
Cross references
Cross references to another place in the document or to another document are in the text with
page number.
Examples:
• Check the tight seat of all screws on the machine, see Page14. (INFO: If you use an
electronic version of this document, click on the link to go to the specified page.)
• For further information, refer to the operating instructions of the universal shaft
manufacturer.
1.6.2 Information on direction
Directional information in this document, such as front, rear, right and left, applies in the
direction of travel of the machine.
1.6.3 Term “machine”
Throughout the rest of this document, the “exact forage harvester” will also be referred to as the
“machine”.
1.6.4 Figures
The figures in this document do not always represent the exact machine type. The information
that refers to the figure always corresponds to the machine type of this document.
1.6.5 Scope of the document
In addition to standard equipment, accessories kits and versions of the machine are described
in this document. Your machine may deviate from this document.
1.6.6 Means of representation
Icons in the text
The following means of representation (icons) are used to present the text more clearly:
Information on This Document 1
How to use this document 1.6
BiG X 580
Original operating instructions 150001257_06_us 15
This arrow characterizes an action step. Several arrows in a row identify a sequence of
actions to be performed step by step.
This icon identifies a prerequisite that has to be fulfilled to perform an action step or a
sequence of actions.
This arrow marks the intermediate result of an action step.
This arrow identifies the result of an action step or sequence of actions.
This bullet point identifies an enumeration. If the bullet point is intended, it identifies the
second level of the enumeration.
Icons in figures
The following icons can be used in illustrations:
Icon Explanation Icon Explanation
1
Reference sign for part
I
Position of a part (e.g. move from
position I to position II)
X
Dimensions (e. g. also W = width,
H = height, L = length)
Magnification of display detail
LH
Left side of machine
RH
Right side of machine
Direction of travel Direction of motion
Reference line for visible material Reference line for covered mater-
ial
Centre line Cable routes
Open Closed
Apply liquid lubricant (e.g. lubric-
ating oil)
Apply lubricating grease
Warning signs
Warnings of dangers are separated from the remaining text as warning signs and are identified
with a danger sign and signal words.
The warning signs must be read and the measures must be observed in order to prevent
personal injury.
Explanation of danger sign
This is the danger sign that warns of a risk of injury.
Please observe all notes marked with the danger sign in order to avoid injuries or death.
1 Information on This Document
1.6 How to use this document
16
BiG X 580
Original operating instructions 150001257_06_us
Explanation of signal words
DANGER
The signal word DANGER warns of a hazardous situation which will result in serious injuries
or death if the warning sign is ignored.
WARNING
The signal word WARNING warns of a hazardous situation which will result in serious injuries
or death if the warning sign is ignored.
CAUTION
The signal word CAUTION warns of a hazardous situation which will result in minor to
moderate injuries if the warning sign is ignored.
Example of a warning sign:
WARNING
Eye damage caused by flying dirt particles
When cleaning with compressed air, dirt particles are ejected at high speed and could get into
the eyes. Therefore eyes could be hurt.
Keep people away from the working area.
Wear personal protective equipment when performing cleaning work with compressed air
(e.g. eye protection).
Warnings of property damage/environmental damage
Warnings of property/environmental damage are separated from the remaining text and marked
with "Notice".
Example:
NOTICE
Gearbox damage due to low oil level
The gearboxes could be damaged when the oil level is too low.
Check gear oil level at regular intervals and top up oil, if necessary.
Check gear oil level approx. 3 to 4 hours after the machine has been switched off. Check
oil level only when machine is in horizontal position.
Notices with information and recommendations
Additional information and recommendations for trouble-free and productive operation of the
machine are separated from the remaining text and marked with “Information”.
Example:
INFO
Each safety sign is provided with an order number and can be ordered directly from the
manufacturer or from an authorised specialist dealer.
Information on This Document 1
How to use this document 1.6
BiG X 580
Original operating instructions 150001257_06_us 17
1.6.7 Conversion table
The following table can be used to convert metric units into US units.
Size SI units (metric) Factor Inch-pound units
Unit name Abbrevi-
ation
Unit name Abbrevi-
ation
Area Hectare ha 2.47105 Acre acres
Volume flow Litres per minute L/min 0.2642 US gallons per
minute
gpm
Cubic metres
per hour
m³/h 4.4029
Force Newton N 0.2248 Pound force lbf
Length Millimetre mm 0.03937 Inch in.
Metre m 3.2808 Foot ft.
Power Kilowatt kW 1.3410 Horsepower hp
Pressure Kilopascal kPa 0.1450 Pounds per
square inch
psi
Megapascal MPa 145.0377
bar (non-SI) bar 14.5038
Torque Newtonmeter Nm 0.7376 pound-foot or
foot-pound
ft∙lbf
8.8507 pound-inch or
inch-pound
in∙lbf
Temperature Degrees Celsius °C °Cx1.8+32 Degrees
Fahrenheit
°F
Velocity Metres per
minute
m/min 3.2808 Feet per minute ft/min
Metres per
second
m/s 3.2808 Feet per second ft/s
Kilometres per
hour
km/h 0.6215 Miles per hour mph
Volumes Litres L 0.2642 US gallon US gal.
Millilitre ml 0.0338 US ounce US oz.
Cubic centi-
metre
cm³ 0.0610 Cubic inch in³
Weight Kilogram kg 2.2046 Pound lbs
2 Safety
2.1 Intended use
18
BiG X 580
Original operating instructions 150001257_06_us
2 Safety
2.1 Intended use
This machine is a self-propelled forage harvester and is used to chop crops.
The crops designated for the intended use of this machine in conjunction with
• a KRONE XCollect are harvested thick-stemmed forage plants, e.g. maize plants,
• a KRONE EasyCollect are harvested thick-stemmed forage plants, e.g. maize plants,
• a KRONE XDisc are mown stalk and leaf crops,
• a KRONE EasyFlow collected stalk and leaf crops,
• a header for smallwood crops from cut groves.
The machine is designed exclusively for use in agriculture and may only be used when
• all safety devices are available according to the operating instructions and are located in the
protective position.
• all safety instructions of the operating instructions have been observed and complied with,
both in chapter “Basic safety instructions”, see Page19, and directly in the chapters of the
operating instructions.
The machine may be used only by people who satisfy the personnel qualification requirements
designated by the machine manufacturer, see Page19.
These operating instructions are part of the machine and must therefore be at hand when the
machine is in use. The machine may be operated only when the operator has received training
and in compliance with these operating instructions.
If the machine is used for applications which are not described in these operating instructions,
this may result in serious injuries or death and damage to the machine and other property.
Unauthorised modifications to the machine may affect the properties of the machine or disrupt
the proper operation. For this reason, unauthorised modifications shall exclude any liability of
the manufacturer for consequential damage.
The intended use shall also include the adherence to the operating, maintenance and repair
conditions set by the manufacturer.
2.2 Reasonably foreseeable misuse
Any use beyond the intended usesee Page18 is regarded as improper use and is therefore
misuse according to the Machinery Directive. The manufacturer is not liable for damage
resulting from this, the user alone bears the risk.
Such misuse is for example:
• Processing of crops which are outside the intended use of the machine,see Page18
• Transport of people
• Transport of goods
• Exceeding the permitted technical gross weight
• Non-compliance with the safety labels on the machine and safety notes in the operating
instructions
• Performing troubleshooting, setting, cleaning, repair and maintenance work contrary to the
information in the operating instructions
• Unauthorised modifications to the machine
• Attachment of unauthorised or unapproved additional equipment
• Use of spare parts which are not KRONE original spare parts
• Stationary operation of the machine
Unauthorised modifications to the machine may affect the properties of the machine or disrupt
proper operation. For this reason, unauthorised modifications will exclude any liability of the
manufacturer for consequential damage.
Safety 2
Service life of the machine 2.3
BiG X 580
Original operating instructions 150001257_06_us 19
2.3 Service life of the machine
• The service life of this machine depends on its proper operation and maintenance as well
as the operating and harvesting conditions.
• By heeding the instructions and information in these operating instructions, permanent
operational readiness and a long service life of the machine can be achieved.
• After each operating season, inspect the entire machine for wear and other damage.
• Replace damaged and worn components before recommissioning the machine.
• Carry out a full technical inspection of the machine after five years of machine operation
and make a decision on further machine usage taking the results of this inspection into
account.
• Theoretically, the service life of this machine is unlimited as all worn or damaged
components can be replaced.
2.4 Basic safety instructions
Non-compliance with the safety instructions and warnings
Non-compliance with the safety instructions and warnings may result in injuries and damage to
the environment and property.
2.4.1 Importance of operating instructions
The operating instructions are an important document and a part of the machine. They are
intended for the user and contain information that is relevant to safety.
Only the procedures specified in the operating instructions are safe. If the operating instructions
are not followed, there is a risk of serious or even fatal injuries.
Prior to using the machine for the first time, read and observe the "Basic safety notices"
completely.
Prior to starting work, read and observe the respective sections in the operating instructions
too.
Keep the operating instructions easily accessible for the machine user at all times.
Hand over the operating instructions to subsequent users.
2.4.2 Personnel qualification of the operating personnel
If the machine is not used properly, people may be seriously injured or killed. To avoid
accidents, each person who works with the machine must satisfy the following minimum
requirements:
• He is physically capable of controlling the machine.
• He can work safely with the machine in accordance with these operating instructions.
• He understands the method of operation of the machine within the scope of his work and
can identify and avoid the dangers associated with the work.
• He has read the operating instructions and can implement the information in the operating
instructions accordingly.
• He is familiar with driving vehicles safely.
• For road travel he has adequate knowledge of the highway code and has the stipulated
driving licence.
2 Safety
2.4 Basic safety instructions
20
BiG X 580
Original operating instructions 150001257_06_us
2.4.3 Personnel qualification of the technicians
If the work (assembly, conversion, modification, extension, repairs, retrofitting) is performed
improperly on the machine, people may be seriously or fatally injured. To avoid accidents,
everyone who performs work according to these instructions must meet the following minimum
requirements:
• Qualified professional, with relevant training.
• Capable of assembling the (partially) disassembled machine according to the assembly
instructions provided by the manufacturer.
• He is capable, e.g. by attending a training course, of extending, modifying or repairing the
function of the machine according to the relevant instructions provided by the manufacturer.
• He has read the operating instructions and can implement the information in the operating
instructions accordingly.
• Ability to perform the work safely according to these instructions.
• Understands the mode of operation of the work to be performed and the machine and is
able to identify and avoid risk in carrying out the necessary work.
• Has read these instructions and is able to implement the information explained in these
instructions accordingly.
2.4.4 Children in danger
Children are not in a position to assess dangers and behave unpredictably.
Thus children are particularly at risk.
• Children are especially at risk when climbing up and down the machine.
• There is no possibility to secure children sufficiently on the self-propelled machine.
• Vibrations can be particularly harmful to children's bodies.
• Children may initiate dangerous movements of the machine.
Never take children on the self-propelled harvester.
Keep children away from the machine.
Keep children away from consumables.
Make sure that there are no children in the danger zone, especially when starting and
triggering machine movements.
2.4.5 Connecting the machine
If headers or trailers not connected properly to the forage harvester, serious accidents could be
caused.
When connecting, observe the following operating instructions:
• the header operating instructions
• the trailer operating instructions
• the machine operating instructions
• the universal shaft operating instructions
Follow the coupling instructions:
• for headers see Page206 und see Page224.
• for trailers see Page267
Observe the changed driving behaviour of the combination.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
