Original operating instructions
Document number: 150001258_06_en
Version: 24/04/2023
BX201-42
Precision forage harvester
BiG X 630
From machine number: 1126759
2
BiG X 630
Original operating instructions 150001258_06_en
Contact
Maschinenfabrik Bernard Krone GmbH & Co. KG
Heinrich-Krone-Straße 10
48480 Spelle
Germany
Telephone main office + 49 (0) 59 77/935-0
Telefax main office + 49 (0) 59 77/935-339
Telefax spare parts warehouse na-
tional territory
+ 49 (0) 59 77/935-239
Telefax spare parts warehouse export + 49 (0) 59 77/935-359
Internet www.landmaschinen.krone.de
https://mediathek.krone.de/
For information on your KRONE machines, also refer to mykrone.green. After you have
registered, you can generate and manage your machines via the machine number so that you
can view the machine data. Via your personal account, you can also access all KRONE
Services.
Information for enquiries and orders
Model
Vehicle identification number
Year of manufacture
Contact data of your dealer
Table of contents
BiG X 630
Original operating instructions 150001258_06_en 3
1 Information on This Document...............................................................................................13
1.1 Validity .......................................................................................................................................13
1.2 Significance of the document.....................................................................................................13
1.3 Re-ordering ................................................................................................................................13
1.4 Applicable documents................................................................................................................13
1.5 Target group of this document ...................................................................................................13
1.6 How to use this document..........................................................................................................14
1.6.1 Directories and references.........................................................................................................14
1.6.2 Information on direction .............................................................................................................14
1.6.3 Term “machine”..........................................................................................................................14
1.6.4 Figures .......................................................................................................................................14
1.6.5 Scope of the document ..............................................................................................................14
1.6.6 Means of representation ............................................................................................................14
1.6.7 Conversion table ........................................................................................................................17
2 Safety ........................................................................................................................................18
2.1 Intended use ..............................................................................................................................18
2.2 Reasonably foreseeable misuse................................................................................................18
2.3 Service life of the machine.........................................................................................................19
2.4 Basic safety instructions ............................................................................................................19
2.4.1 Importance of operating instructions..........................................................................................19
2.4.2 Personnel qualification of the operating personnel ....................................................................19
2.4.3 Personnel qualification of the technicians..................................................................................20
2.4.4 Children in danger......................................................................................................................20
2.4.5 Connecting the machine ............................................................................................................20
2.4.6 Structural modifications on the machine ....................................................................................21
2.4.7 Additional equipment and spare parts .......................................................................................21
2.4.8 Jobs on the machine..................................................................................................................21
2.4.9 Operational safety: Technically sound condition........................................................................22
2.4.10 Danger zones.............................................................................................................................23
2.4.11 Ensuring functionality of safety devices .....................................................................................25
2.4.12 Personal protective equipment ..................................................................................................25
2.4.13 Safety sign on the machine........................................................................................................26
2.4.14 Road safety................................................................................................................................26
2.4.15 Parking the machine safely .......................................................................................................27
2.4.16 Consumables .............................................................................................................................27
2.4.17 Chemicals ..................................................................................................................................28
2.4.18 Dangers arising from environment.............................................................................................28
2.4.19 Sources of danger on the machine ............................................................................................30
2.4.20 Dangers in connection with certain activities: climbing up and down ........................................31
2.4.21 Dangers in connection with certain activities: Working on the machine ....................................32
2.4.22 Dangers in connection with certain activities: checking and charging batteries ........................33
2.4.23 Dangers in connection with certain activities: working on wheels and tyres..............................33
2.4.24 Behaviour in dangerous situations and in case of accidents .....................................................34
2.5 Safety routines ...........................................................................................................................34
2.5.1 Shutting down and safeguarding the machine...........................................................................34
2.5.2 Securing raised machine and machine parts against lowering..................................................35
2.5.3 Carrying out oil level check and oil and filter element changes safely.......................................35
2.5.4 Running actuator test.................................................................................................................36
2.6 Safety sign on the machine........................................................................................................36
2.7 Information signs on the machine ..............................................................................................57
2.8 Safety equipment .......................................................................................................................65
2.8.1 SMV emblem .............................................................................................................................67
2.8.2 Fire extinguisher ........................................................................................................................67
3 Data memory ............................................................................................................................69
4 Machine Description................................................................................................................70
4.1 Machine overview ......................................................................................................................70
4.1.1 Contents of the storage compartment........................................................................................71
4.2 Labelling.....................................................................................................................................72
4.3 Lighting ......................................................................................................................................73
Table of contents
4
BiG X 630
Original operating instructions 150001258_06_en
4.3.1 Road travel lighting ....................................................................................................................73
4.3.2 Working lights ............................................................................................................................74
4.3.3 Maintenance lighting ..................................................................................................................75
4.4 Function description chopping crops .........................................................................................76
5 Technical Data..........................................................................................................................78
5.1 Dimensions ................................................................................................................................78
5.2 Weights ......................................................................................................................................78
5.3 Technically permitted maximum speed (road travel) .................................................................78
5.4 Engine data................................................................................................................................79
5.5 Traction drive .............................................................................................................................79
5.6 Electrical system ........................................................................................................................79
5.7 Airborne noise emission.............................................................................................................79
5.8 Ambient temperature .................................................................................................................80
5.9 Vibration values .........................................................................................................................80
5.10 tow coupling ...............................................................................................................................80
5.11 Power supply for headers – power ............................................................................................80
5.12 Power supply for headers – hydraulics ......................................................................................80
5.13 Power supply for headers – electrics .........................................................................................80
5.14 Consumables .............................................................................................................................80
5.14.1 Oils.............................................................................................................................................81
5.14.2 Lubricating grease .....................................................................................................................83
5.14.3 Coolant.......................................................................................................................................83
5.14.4 Refrigerant (air conditioning)......................................................................................................83
5.14.5 Fuel/urea....................................................................................................................................84
5.15 Tyres ..........................................................................................................................................84
5.16 Total weights and axle loads......................................................................................................85
5.17 Released headers......................................................................................................................88
6 Control and Display Elements ................................................................................................90
6.1 Overview of operating elements ................................................................................................90
6.2 Opening doors and windows of cabin .......................................................................................90
6.3 Control and display elements on the steering column ...............................................................93
6.3.1 Steering column switch ..............................................................................................................93
6.3.1.1 Activating horn ...........................................................................................................................93
6.3.1.2 Switching direction indicators on/off...........................................................................................94
6.3.1.3 Switching parking light, dipped beam and work lightings on/off.................................................94
6.3.1.4 Switching full beam on/off ..........................................................................................................96
6.3.1.5 Actuating headlamp flasher .......................................................................................................96
6.3.1.6 Switching windshield wipers on/off ...........................................................................................96
6.3.2 Indicator and warning lamps ......................................................................................................97
6.3.3 Switching the flashing warning light on/off .................................................................................98
6.4 Actuating service brake..............................................................................................................98
6.5 Actuate the trailer brake system (for "trailer brake system" version) .........................................99
6.6 Actuating the momentary foot switches (for "Momentary foot switches in the cabin" version) 100
6.7 Mirror adjuster..........................................................................................................................100
6.8 Setting the anti-collision mirror.................................................................................................101
6.9 Keypad for wiper and warning beacon.....................................................................................102
6.10 Lighting on the cabin ladder and right ladder...........................................................................102
6.11 Interior lighting .........................................................................................................................104
6.12 Operating elements on control lever ........................................................................................104
6.13 Control and display elements on the keypad ...........................................................................108
6.14 Main mode switch ....................................................................................................................110
6.15 Quick-stop switch.....................................................................................................................111
6.16 Navigation module ...................................................................................................................111
6.17 Ignition lock ..............................................................................................................................113
6.18 Additional keypad.....................................................................................................................113
6.19 Sockets ....................................................................................................................................114
6.19.1 Cigarette lighter 12 Volt ...........................................................................................................114
6.19.2 12 V socket/24 V socket ..........................................................................................................115
6.19.3 Diagnostics sockets .................................................................................................................116
6.19.4 In-cab socket............................................................................................................................116
Table of contents
BiG X 630
Original operating instructions 150001258_06_en 5
6.19.5 USB connection .......................................................................................................................116
6.20 Grinding control unit.................................................................................................................117
6.21 Quick-stop switch grinding control unit ....................................................................................118
6.22 Opening and closing side hoods and rear hood ......................................................................119
7 Initial operation ......................................................................................................................120
7.1 Checklist for initial operation ....................................................................................................120
7.2 Mounting warning panels in operating position........................................................................121
7.3 Mounting fire extinguisher........................................................................................................121
7.4 Mounting licence plate .............................................................................................................122
8 Start-up ...................................................................................................................................123
8.1 Check before start-up ..............................................................................................................123
8.2 Setting driver’s seat .................................................................................................................124
8.2.1 Air-cushioned comfort seat ......................................................................................................124
8.2.1.1 Operating air-cushioned comfort seat (for "Standard" version)................................................125
8.2.1.2 Operating air-cushioned comfort seat (for "ACTIVO" version).................................................127
8.2.1.3 Turning the driver's seat (for the "Swivel seat adapter" design) ..............................................131
8.2.2 Steering column adjustment ....................................................................................................131
8.2.3 Setting the terminal ..................................................................................................................132
8.2.4 Monitor for camera monitoring .................................................................................................133
8.2.5 Sun visor ..................................................................................................................................134
8.2.6 Adjustable air nozzles ..............................................................................................................135
8.2.7 Inside rear mirror......................................................................................................................135
8.3 General aspects.......................................................................................................................135
8.3.1 Instructional seat......................................................................................................................135
8.3.2 Cooling box (version with "Insulated thermobox")....................................................................136
8.3.3 Drawer for first-aid kit and operating instructions.....................................................................136
9 Start-up – Grass mode/direct cut header ............................................................................137
9.1 Removing the corn conditioner ................................................................................................138
9.2 Installing the grass channel .....................................................................................................142
9.3 Adjusting the air intake.............................................................................................................143
9.4 Removing round brush from the rotating screen......................................................................144
9.5 Setting Lifting Unit Hydraulics ..................................................................................................144
9.6 Removing grain capture sheet .................................................................................................145
9.7 Removing spout extension.......................................................................................................146
9.8 Mounting camera in grass mode position (for "EasyLoad auto-loading system" version) .......148
9.9 Dismounting camera in maize mode position (for "EasyLoad auto-loading system" version) .149
9.10 Removing rear weight ..............................................................................................................150
9.11 Removing husk comb (version with "Husk comb")...................................................................152
9.11.1 Removing the maintenance flap and deflector sheet...............................................................152
9.11.2 Removing blade support and husk comb.................................................................................154
9.11.3 Removing wear plate ...............................................................................................................155
9.11.4 Mounting wear plate (without window) and deflector sheet .....................................................155
9.11.5 Mounting maintenance flap transfer shaft................................................................................156
9.12 Removing additional axle.........................................................................................................156
10 Commissioning – Maize mode..............................................................................................164
10.1 Removing the grass channel ...................................................................................................165
10.2 Installing the corn conditioner ..................................................................................................166
10.3 Adjusting the air intake.............................................................................................................170
10.4 Pressing round brushes onto the rotating screen ....................................................................171
10.5 Adjusting the lifting unit hydraulics...........................................................................................172
10.6 Mounting grain capture sheet ..................................................................................................172
10.7 Mounting spout extension ........................................................................................................173
10.8 Mounting camera in maize mode position (for "EasyLoad auto-loading system" version) ......178
10.9 Dismounting camera in grass mode position (for "EasyLoad auto-loading system" version) ..180
10.10 Attaching rear weight ...............................................................................................................180
10.11 Installing husk comb (version with "Husk comb").....................................................................183
10.11.1 Removing the maintenance flap transfer shaft and wear plate................................................183
10.11.2 Mounting wear plate.................................................................................................................185
Table of contents
6
BiG X 630
Original operating instructions 150001258_06_en
10.11.3 Mounting husk comb................................................................................................................186
10.11.4 Mounting blade support ...........................................................................................................187
10.11.5 Mounting maintenance flap transfer shaft and deflector sheet ................................................189
10.12 Mounting additional axle ..........................................................................................................190
11 Commissioning – Grass/maize mode for the transition period.........................................200
12 Start-up – Attaching and removing EasyFlow ....................................................................204
12.1 Mounting EasyFlow..................................................................................................................205
12.1.1 Preparing the intake.................................................................................................................205
12.1.2 Connecting EasyFlow ..............................................................................................................206
12.1.3 Connecting hydraulic hoses.....................................................................................................208
12.1.4 Moving parking jacks on right/left into transport position .........................................................209
12.2 Removing EasyFlow ................................................................................................................209
12.3 Putting Down EasyFlow ...........................................................................................................211
13 Commissioning – Attaching and removing XCollect..........................................................212
13.1 Attaching XCollect....................................................................................................................213
13.1.1 Preparing the intake.................................................................................................................213
13.1.2 Connecting XCollect ................................................................................................................214
13.1.3 Connecting hydraulic hoses.....................................................................................................216
13.1.4 Moving support jacks on right/left into transport position .........................................................217
13.1.5 Enabling additional axle on the terminal ..................................................................................218
13.2 Removing XCollect ..................................................................................................................218
13.3 Parking XCollect ......................................................................................................................221
14 Start-up – Attaching and removing EasyCollect.................................................................222
14.1 Mounting EasyCollect ..............................................................................................................223
14.1.1 Preparing the intake.................................................................................................................223
14.1.2 Connecting EasyCollect...........................................................................................................224
14.1.3 Connecting hydraulic hoses.....................................................................................................226
14.1.4 Moving parking jacks on right/left into transport position .........................................................227
14.2 Removing EasyCollect.............................................................................................................228
14.3 Putting down EasyCollect .......................................................................................................231
15 Start-up – Attaching and removing XDisc ...........................................................................232
15.1 Mounting XDisc........................................................................................................................233
15.1.1 Preparing the intake.................................................................................................................233
15.1.2 Connecting XDisc ....................................................................................................................233
15.1.3 Moving parking jacks on right/left into transport position .........................................................236
15.2 Removing XDisc ......................................................................................................................236
15.3 Putting down XDisc..................................................................................................................238
16 Driving and Transport ...........................................................................................................239
16.1 Preparing the machine for road travel......................................................................................239
16.1.1 Transport position ....................................................................................................................240
16.1.2 Moving header to transport position.........................................................................................240
16.1.3 Moving intake into transport position .......................................................................................243
16.1.4 Swivelling spout into transport position....................................................................................243
16.1.5 Opening the stop cock additional running gear on the XCollect ..............................................244
16.2 Starting engine.........................................................................................................................244
16.2.1 Observing indicator and warning lamps...................................................................................246
16.3 Behaviour after the engine has stalled.....................................................................................247
16.4 Starting up machine .................................................................................................................247
16.4.1 Setting the acceleration behaviour...........................................................................................248
16.4.2 Notes on driving the machine ..................................................................................................248
16.4.3 Driving forwards and stopping .................................................................................................249
16.4.3.1 Cruise control...........................................................................................................................249
16.4.4 Driving backward and stopping................................................................................................251
16.5 Stopping the machine ..............................................................................................................251
16.5.1 Stopping machine by using control lever .................................................................................252
16.5.2 Stopping machine with the service brake ................................................................................253
16.6 Couple brake pedals (for "trailer brake system" version).........................................................254
Table of contents
BiG X 630
Original operating instructions 150001258_06_en 7
16.7 Applying parking brake ............................................................................................................254
16.8 Switching off the engine...........................................................................................................256
16.9 Fitting wheel chocks.................................................................................................................256
16.10 Main battery switch ..................................................................................................................257
16.11 Parking the machine ................................................................................................................257
16.12 Towing the machine.................................................................................................................258
16.12.1 Releasing the parking brake manually.....................................................................................259
16.13 Preparing the machine for shipment ........................................................................................260
16.13.1 Lashing the machine................................................................................................................260
16.13.2 Removing the machine wheels ................................................................................................261
17 Operation device....................................................................................................................262
17.1 Raising and lowering lifting unit ...............................................................................................263
17.2 Aligning pendulum tube horizontally ........................................................................................263
17.3 Releasing header locking.........................................................................................................264
17.4 Trailer operation.......................................................................................................................265
17.4.1 Connecting trailer.....................................................................................................................266
17.4.2 Disconnecting trailer ................................................................................................................267
17.5 Additional axles........................................................................................................................268
17.5.1 Maize mode .............................................................................................................................269
17.5.2 Grass mode .............................................................................................................................269
17.5.3 XDisc operating mode..............................................................................................................269
17.6 Silage additives unit .................................................................................................................270
17.6.1 Internal silage additives unit coarse dosing (for version with "Controlled silage additives unit")
.................................................................................................................................................270
17.6.2 Internal silage additives unit fine dosing (for "regulated silage additives unit fine dosing" version)
.................................................................................................................................................276
17.6.3 Connecting an additional silage additives unit (for "External silage additives unit" version)....282
17.7 Field mode on slopes...............................................................................................................282
17.8 Setting inclination-dependent distribution of traction of the traction drive (for "inclination sensor"
version) ....................................................................................................................................283
17.9 Fast change of direction of travel (fast reversing)....................................................................283
17.10 Operating intake/header ..........................................................................................................284
17.11 Lifting unit control.....................................................................................................................286
17.12 Setting spout ...........................................................................................................................289
17.13 Adjusting discharge distance ...................................................................................................290
17.14 TractionControl/Traction control system ..................................................................................290
17.15 Automatic steering system.......................................................................................................291
17.16 Setting chop length ..................................................................................................................293
17.17 Metal detection.........................................................................................................................295
17.18 RockProtect .............................................................................................................................296
17.19 ConstantPower ........................................................................................................................297
17.20 Engine speed management .....................................................................................................298
17.21 AutoScan .................................................................................................................................299
17.22 CropControl..............................................................................................................................299
17.23 PowerSplit................................................................................................................................301
17.24 Contents sensor system ..........................................................................................................303
17.25 Operating VariQuick electrically...............................................................................................305
17.26 Operating VariLOC chop length gearbox.................................................................................306
17.26.1 Switching VariLOC cutting length gearbox ..............................................................................308
17.26.2 VariLOC cutting length gearbox settings on the terminal.........................................................309
17.27 Operating the EasyLoad auto-loading system .........................................................................312
17.27.1 Camera monitor status display ................................................................................................312
17.27.2 Setting EasyLoad auto-loading system....................................................................................314
17.27.3 Activating/deactivating EasyLoad auto-loading system ...........................................................317
17.27.4 Selecting filling strategy ...........................................................................................................317
17.27.5 Filling to rear ............................................................................................................................318
17.28 Operating the dirt seal..............................................................................................................319
18 Terminal ..................................................................................................................................321
18.1 Display design..........................................................................................................................321
18.2 Description display...................................................................................................................322
Table of contents
8
BiG X 630
Original operating instructions 150001258_06_en
18.3 Possible terminals....................................................................................................................322
18.4 Input window ............................................................................................................................323
18.5 Selection window .....................................................................................................................324
19 Terminal machine functions .................................................................................................326
19.1 Status line ................................................................................................................................327
19.2 Malfunctions indicated on malfunction warning panel..............................................................332
19.2.1 Warning lamps – urea tank filling level ....................................................................................334
19.2.2 Warning lamps – urea quality ..................................................................................................334
19.2.3 Warning lamps – urea system defective or tampered with ......................................................335
19.2.4 Warning lamps – load condition diesel particulate filter ...........................................................337
19.3 Keys in the title bar ..................................................................................................................338
19.3.1 “Counters” menu ......................................................................................................................338
19.3.2 “Error” menu.............................................................................................................................348
19.3.3 Main menu ...............................................................................................................................352
19.4 Direct input “Field mode”..........................................................................................................352
19.4.1 Temporarily change working width or number of rows ............................................................353
19.4.2 Changing the header speed.....................................................................................................354
19.4.3 Change chop length.................................................................................................................354
19.4.4 Changing the lifting unit control default value ..........................................................................355
19.4.5 Changing Corn Conditioner Roller Distance ............................................................................355
19.5 Information area.......................................................................................................................356
19.6 Engine and driving data display range.....................................................................................356
19.7 Displaying malfunctions in the "Engine and driving data" display range..................................361
19.8 Traction drive indicator lights ...................................................................................................361
20 Terminal - Menus ...................................................................................................................364
20.1 Menu structure .........................................................................................................................364
20.2 Bringing up menu level ............................................................................................................374
20.3 Navigating in menus ................................................................................................................375
20.3.1 Changing/saving parameter.....................................................................................................375
20.4 “Diagnostics” menu explanation...............................................................................................375
20.5 "Machine" menu.......................................................................................................................377
20.5.1 "Electronics" menu...................................................................................................................379
20.5.1.1 "E-Solutions" menu ..................................................................................................................380
20.5.1.2 "Telemetry" menu.....................................................................................................................380
20.5.1.3 "Active errors" menu ................................................................................................................382
20.5.1.4 "Error history" menu.................................................................................................................383
20.5.1.5 "Control units overview" menu .................................................................................................384
20.5.1.6 "Control unit versions" menu....................................................................................................386
20.5.1.7 "Information" menu...................................................................................................................387
20.5.2 "Lighting" menu........................................................................................................................387
20.5.3 "Camera systems" menu..........................................................................................................389
20.5.3.1 "Camera system" menu ...........................................................................................................390
20.5.3.2 "Surround View" menu.............................................................................................................390
20.6 “Cabin” menu ...........................................................................................................................391
20.6.1 “Terminal” menu.......................................................................................................................393
20.6.2 “Armrest” menu ........................................................................................................................394
20.6.3 “Control Lever” menu ...............................................................................................................396
20.6.4 "Interior lighting" menu.............................................................................................................397
20.6.5 “Control Unit Versions” menu...................................................................................................398
20.6.6 “Printer” menu ..........................................................................................................................399
20.6.7 "Automatic climate control" menu ............................................................................................399
20.6.8 "Wiper" menu ...........................................................................................................................401
20.6.9 "Mirror heating" menu ..............................................................................................................402
20.6.10 "Momentary foot switch" menu.................................................................................................402
20.7 "Lubrication" menu...................................................................................................................403
20.7.1 "Central lubrication" menu........................................................................................................404
20.7.2 "Intermediate gearbox" menu...................................................................................................406
20.8 "Crop flow" menu .....................................................................................................................406
20.8.1 “Header” menu.........................................................................................................................410
20.8.2 “Header Drive” menu ...............................................................................................................410
Table of contents
BiG X 630
Original operating instructions 150001258_06_en 9
20.8.3 "AutoScan" menu.....................................................................................................................411
20.8.4 “Intake” menu...........................................................................................................................412
20.8.5 "Foreign object detection" menu ..............................................................................................412
20.8.6 “Lifting Unit” menu....................................................................................................................413
20.8.7 "Grinding device and counterblade" menu...............................................................................414
20.8.8 “Main Coupling” menu..............................................................................................................417
20.8.9 “Corn Conditioner” menu .........................................................................................................418
20.8.10 “Discharge Accelerator” menu .................................................................................................421
20.8.11 "Content material sensor" menu ..............................................................................................422
20.8.12 "CropControl" menu .................................................................................................................423
20.8.13 "Silage additives units" menu...................................................................................................426
20.8.13.1 "External silage additives unit" menu.......................................................................................426
20.8.13.2 "Silage additives unit fine dosing" menu ..................................................................................426
20.8.13.3 "Silage additives unit coarse dosing" menu .............................................................................427
20.9 "Spout" menu ...........................................................................................................................428
20.9.1 "Spout" menu ...........................................................................................................................429
20.9.2 "Auto-loading system" menu....................................................................................................431
20.10 “Engine” menu .........................................................................................................................432
20.10.1 “Diesel Engine” menu ..............................................................................................................432
20.10.2 “ConstantPower” menu ...........................................................................................................434
20.10.3 "Compressed air cleaning" menu.............................................................................................435
20.11 “Hydraulics” menu....................................................................................................................436
20.11.1 “Header Locking” menu ..........................................................................................................437
20.11.2 “Work Hydraulics” menu ..........................................................................................................437
20.11.3 “Auxiliary Hydraulics” menu .....................................................................................................438
20.12 “Drive Functions” menu............................................................................................................438
20.12.1 “Automatic Steering System” menu .........................................................................................440
20.12.2 “Traction Drive” Menu ..............................................................................................................440
20.12.3 “Additional Axle” menu.............................................................................................................443
20.12.4 “Rear Axle” menu.....................................................................................................................443
20.12.5 "Trailer brake" menu ................................................................................................................445
20.13 “Season Settings” menu ..........................................................................................................445
20.14 "User level" menu.....................................................................................................................446
21 Settings...................................................................................................................................447
21.1 Optimising crop flow.................................................................................................................447
21.2 Optimising discharge capacity of the machine.........................................................................448
21.2.1 Adjusting overhang of chopping blades ...................................................................................448
21.2.2 Setting drum base ...................................................................................................................448
21.2.3 Setting the rear wall of the discharge accelerator....................................................................451
21.3 Setting the corn conditioner/grass channel holding-down clamp.............................................456
21.4 Setting deflector sheet on the corn conditioner........................................................................456
22 Maintenance - General Information......................................................................................458
22.1 Observe the service record booklet .........................................................................................458
22.2 Maintenance table....................................................................................................................459
22.2.1 Maintenance – Before the season ...........................................................................................459
22.2.2 Maintenance – After the season ..............................................................................................460
22.2.3 Maintenance - once after 1 hour .............................................................................................461
22.2.4 Maintenance - once after 4 hours ............................................................................................462
22.2.5 Maintenance - once after 10 hours ..........................................................................................462
22.2.6 Maintenance – 6 times after every 10 hours............................................................................462
22.2.7 Maintenance - Once after 50 hours .........................................................................................462
22.2.8 Maintenance – Once after 200 hours.......................................................................................463
22.2.9 Maintenance – Once after 1,000 km........................................................................................463
22.2.10 Maintenance - Every 10 hours, but at least once a day...........................................................463
22.2.11 Maintenance – Weekly.............................................................................................................465
22.2.12 Maintenance – Every 30 hours ................................................................................................465
22.2.13 Maintenance - Every 50 hours .................................................................................................465
22.2.14 Maintenance - every 100 hours ...............................................................................................465
22.2.15 Maintenance - every 250 hours ...............................................................................................466
22.2.16 Maintenance - Every 500 hours ...............................................................................................466
Table of contents
10
BiG X 630
Original operating instructions 150001258_06_en
22.2.17 Maintenance - Every 750 hours, at least every 2 years...........................................................468
22.2.18 Maintenance - every 1,000 hours but at least at the end of the season ..................................468
22.2.19 Maintenance – Every 3000 hours ............................................................................................468
22.2.20 Maintenance - every 3 years....................................................................................................468
22.2.21 Maintenance - as required .......................................................................................................469
22.3 Tightening torques ...................................................................................................................470
22.4 Cleaning the machine ..............................................................................................................473
22.5 Compressed air connections to clean with compressed air.....................................................474
23 Maintenance - Engine ............................................................................................................476
23.1 Engine overview ......................................................................................................................477
23.2 Dirt deposits in engine compartment .......................................................................................477
23.2.1 Cleaning engine compartment with compressed air ................................................................478
23.3 Engine oil level.........................................................................................................................478
23.3.1 Checking engine oil level ........................................................................................................479
23.3.2 Topping up engine oil...............................................................................................................479
23.4 Fuel prefilter/water separator ...................................................................................................480
23.4.1 Changing the fuel filter element ...............................................................................................480
23.4.2 Cleaning the fuel prefilter sight glass .......................................................................................481
23.4.3 Draining condensation water out of the fuel prefilter................................................................481
23.5 Changing urea filter inserts ......................................................................................................482
23.6 Cleaning the non-return valve on the urea pump module........................................................484
23.7 Refuelling .................................................................................................................................486
23.8 Topping up urea solution .........................................................................................................487
23.9 Vent fuel filter ...........................................................................................................................488
23.10 Engine coolant .........................................................................................................................489
23.11 Checking the engine coolant level ...........................................................................................490
23.12 Checking engine piping............................................................................................................491
23.12.1 Checking pipework in the air conditioning and heating system ...............................................491
23.12.2 Checking tubing in engine cooling system...............................................................................492
23.12.3 Checking pipework in air intake and charge air .......................................................................492
23.12.4 Checking fuel lines...................................................................................................................493
23.13 Cleaning air filter ......................................................................................................................493
23.14 Replacing safety cartridge .......................................................................................................494
23.15 Shutting down the diesel engine ..............................................................................................495
24 Maintenance – Compressed Air System..............................................................................496
24.1 Drain condensation water from the compressed air tank.........................................................496
24.2 Retighten tensioning straps at the compressed air tank ..........................................................497
25 Maintenance – Basic Machine ..............................................................................................498
25.1 Cleaning the windows and outside rear-view mirrors of the cabin...........................................498
25.2 Checking/refilling windscreen washer system .........................................................................499
25.3 Maintaining air conditioning and heating..................................................................................500
25.3.1 Components of air conditioning ...............................................................................................500
25.3.2 Carrying out a visual inspection at the receiver/dryer ..............................................................501
25.3.3 Checking the condition and filling quantity of refrigerant ........................................................501
25.3.4 Replacing/cleaning fresh air filter.............................................................................................502
25.3.5 Replacing/cleaning circulation filter..........................................................................................503
25.4 Cleaning cooler and cooler compartment ................................................................................503
25.5 Draining coolant .......................................................................................................................504
25.6 Maintaining chassis..................................................................................................................505
25.6.1 Checking attachment of steering cylinder ................................................................................505
25.6.2 Checking fitting of track rod .....................................................................................................505
25.6.3 Checking the hub cover of the rear axle, with front wheel drive version..................................506
25.6.4 Checking the hub bearing of the rear axle, for the front-wheel drive version...........................506
25.6.5 Checking attachment of wheel hub gearbox............................................................................507
25.7 Maintaining brake (Bosch) .......................................................................................................508
25.8 Maintaining belt drives ............................................................................................................509
25.8.1 Checking kraftband ..................................................................................................................510
25.8.2 Checking pulley........................................................................................................................511
25.9 Maintaining tyres and wheels...................................................................................................511
Table of contents
BiG X 630
Original operating instructions 150001258_06_en 11
25.9.1 Checking/maintaining tyres......................................................................................................511
25.9.2 Retighten wheel nuts ...............................................................................................................512
25.9.3 Running direction of tyres ........................................................................................................512
25.9.4 Changing tyre size ...................................................................................................................512
25.10 Maintaining tow coupling..........................................................................................................513
25.11 Checking the fire extinguisher..................................................................................................514
25.12 Checking the gaps at the mudguards ......................................................................................514
26 Maintenance – Feed System .................................................................................................517
26.1 Removing intake unit with mounting cart .................................................................................517
26.2 Mounting intake unit with installation cart ................................................................................520
26.3 Removing intake unit with header............................................................................................522
26.4 Mounting intake unit with header .............................................................................................524
26.5 Grinding chopping blades ........................................................................................................526
26.5.1 Grinding the chopping blades when intake is not mounted .....................................................528
26.5.2 Checking the grinding stone and cleaning the grinding channel..............................................529
26.5.3 Performing grinding process ....................................................................................................530
26.5.4 Readjusting the counterblade ..................................................................................................531
26.5.5 Grinding and readjusting counterblade (for the version with "automatisch counterblade
adjustment") .............................................................................................................................534
26.6 Readjusting or replacing grinding stone...................................................................................535
26.6.1 Checking grinding stone ..........................................................................................................536
26.6.2 Readjusting grinding stone ......................................................................................................537
26.6.3 Replacing grinding stone .........................................................................................................539
26.7 Readjusting or changing chopping blades ...............................................................................541
26.8 Working with half the number of chopping blades ...................................................................556
26.9 Turning or replacing counterblade ...........................................................................................557
26.10 Operating the mounting cart of the chopper unit (for "Chopper unit mounting cart" design) ...559
26.10.1 Setting mounting cart ...............................................................................................................559
26.10.2 Parking mounting cart ..............................................................................................................560
26.11 Turning or replacing conveyor bars of pre-compression roller.................................................560
26.12 Changing conveyor bars on feed roller ....................................................................................561
26.13 Adjusting the distance between the scraper and flat roller ......................................................561
26.14 Setting the gap compression roller-scraper .............................................................................563
26.15 Setting the tension springs of intake unit .................................................................................565
27 Maintenance - Crop Flow.......................................................................................................567
27.1 Access points to crop flow .......................................................................................................567
27.1.1 Removing the grass channel ...................................................................................................568
27.1.2 Installing the grass channel .....................................................................................................568
27.1.3 Opening maintenance flap transfer shaft .................................................................................568
27.1.4 Removing drum base and grating base (version with "Grating base").....................................569
27.1.5 Mounting drum base and grating base (version with "Grating base")......................................571
27.1.6 Removing the rear wall of the discharge accelerator...............................................................572
27.1.7 Reinstalling the rear wall of the discharge accelerator ............................................................573
27.1.8 Removing maintenance flap in channel support ......................................................................573
27.1.9 Opening maintenance flap in the spout ...................................................................................574
27.2 Maintaining the corn conditioner ..............................................................................................575
27.2.1 Lubricating the deflection roll of the corn conditioner belt after washing .................................575
27.2.2 Check the corn conditioner with rollers for wear and tear........................................................576
27.3 Maintenance discharge accelerator .........................................................................................577
27.3.1 Cleaning the bearing of the discharge accelerator ..................................................................577
27.3.2 Checking discharge scoops ....................................................................................................578
27.3.3 Removing/installing discharge scoops.....................................................................................578
27.3.4 Checking and adjusting discharge accelerator scraper ...........................................................579
27.4 Setting corn conditioner ...........................................................................................................580
27.5 Maintenance husk comb (version with "Husk comb") ..............................................................581
28 Maintenance - Hydraulic System..........................................................................................584
28.1 Pressure limiting valves ...........................................................................................................584
28.2 Hydraulic oil .............................................................................................................................585
28.3 Maintaining hydraulic oil tank...................................................................................................585
Table of contents
12
BiG X 630
Original operating instructions 150001258_06_en
28.4 Changing the high-pressure filter.............................................................................................586
28.5 Checking hydraulic hoses ........................................................................................................587
29 Maintenance - Gearbox .........................................................................................................588
29.1 Overview of gearboxes ............................................................................................................588
29.2 Maintaining transfer gearbox ...................................................................................................589
29.3 Maintaining intermediate gearbox............................................................................................590
29.4 Maintaining intermediate gearbox intake .................................................................................590
29.5 Maintaining bottom roller gearbox............................................................................................591
29.6 Maintaining top roller gearbox..................................................................................................592
29.7 Maintaining wheel hub gearbox ...............................................................................................593
29.8 Maintaining spout rotary drive gearbox....................................................................................596
29.9 Maintaining fan gearbox...........................................................................................................597
29.10 Maintaining power take-off gear...............................................................................................598
29.11 Servicing VariLOC chop length gearbox..................................................................................599
30 Maintenance – Electrics ........................................................................................................601
30.1 Batteries...................................................................................................................................602
30.1.1 Cleaning and maintaining batteries..........................................................................................603
30.1.2 Charging batteries....................................................................................................................603
30.1.3 Replacing batteries .................................................................................................................604
30.2 Maintaining alternator ..............................................................................................................606
30.3 Maintaining starter ...................................................................................................................607
31 Maintenance - Lubrication ....................................................................................................608
31.1 Lubricating universal shafts .....................................................................................................608
31.1.1 Lubricating the universal shaft drive intake..............................................................................609
31.1.2 Lubricating the universal shaft upper roller gearbox ................................................................609
31.1.3 Lubricating universal shaft header ...........................................................................................610
31.1.4 Lubricating the double joint ......................................................................................................611
31.2 Lubrication chart - machine......................................................................................................611
32 Maintenance – Central Lubrication System .......................................................................620
32.1 Distributor blocks of the central lubrication unit .......................................................................620
32.2 Lubricants ................................................................................................................................625
32.3 Filling the lubricant tank ...........................................................................................................625
32.4 Check filling level .....................................................................................................................626
32.5 Starting intermediate lubrication ..............................................................................................627
33 Malfunction, cause and remedy ...........................................................................................628
33.1 Electrics/electronics BiG X defective .......................................................................................628
33.1.1 Cable break, short circuit .........................................................................................................628
33.1.2 Overview of fuses ....................................................................................................................630
33.1.3 Overview of control units..........................................................................................................633
33.1.4 Overview of sensors ................................................................................................................634
33.1.5 Overview actuators ..................................................................................................................635
33.2 Malfunctions in the central lubrication unit ...............................................................................637
33.2.1 Searching for the error in the central lubrication system..........................................................637
33.3 External starting of the machine ..............................................................................................637
33.4 Removing crop blockages in area of crop flow ........................................................................639
33.5 Car jack contact points.............................................................................................................644
34 Waste disposal.......................................................................................................................646
Index........................................................................................................................................647
35 Declaration of conformity .....................................................................................................661
Information on This Document 1
Validity 1.1
BiG X 630
Original operating instructions 150001258_06_en 13
1 Information on This Document
1.1 Validity
This document is valid for machines of type:
BX201-42 (BiG X 630)
All information, illustrations and technical data in this document correspond to the latest state at
the time of publication.
We reserve the right to make design changes at any time and without notification of reasons.
1.2 Significance of the document
This is an important document. It is addressed to the user and contains safety-relevant
information.
Prior to starting work, read the complete document and observe its contents.
Keep this document ready to hand for the user of the machine.
Hand over this document to subsequent users.
1.3 Re-ordering
You can request a replacement document if this document became completely or partly
unusable, or if you need it in a different language. Please specify the document number shown
on the cover page in your order. Alternatively, you can download the document online from
KRONE MEDIA https://media.mykrone.green.
1.4 Applicable documents
To ensure that the machine is used safely and as intended, observe the following further
applicable documents.
• Operating instructions for diesel engine, MTU Friedrichshafen GmbH
• Fuel specification for diesel engine, MTU Friedrichshafen GmbH
• Maintenance instructions for diesel engine, MTU Friedrichshafen GmbH
• Supplement to operating instructions "Error messages, information messages and
parameters"
• Operating instructions for prefilter for diesel fuel, HYDAC
• Operating instructions for header, KRONE
• Operating instructions for transport wagon, KRONE
• KRONE NIR Control dual operating instructions
• Operating instructions for universal shaft
• Circuit diagram, KRONE
• Spare parts list, KRONE
• Service record booklet, KRONE
1.5 Target group of this document
This document aims at the operator of the machine who fulfills the minimum requirements of
personnel qualification,see Page19.
1 Information on This Document
1.6 How to use this document
14
BiG X 630
Original operating instructions 150001258_06_en
1.6 How to use this document
1.6.1 Directories and references
Contents/headers
The contents and headers in this document ensure quick orientation in the chapters.
Index
The index contains catchwords in alphabetical order which enable to find information on a
desired topic easily. The index can be found on the last pages of this document.
Cross references
Cross references to another place in the document or to another document are in the text with
page number.
Examples:
• Check the tight seat of all screws on the machine, see Page14. (INFO: If you use an
electronic version of this document, click on the link to go to the specified page.)
• For further information, refer to the operating instructions of the universal shaft
manufacturer.
1.6.2 Information on direction
Directional information in this document, such as front, rear, right and left, applies in the
direction of travel of the machine.
1.6.3 Term “machine”
Throughout the rest of this document, the “exact forage harvester” will also be referred to as the
“machine”.
1.6.4 Figures
The figures in this document do not always represent the exact machine type. The information
that refers to the figure always corresponds to the machine type of this document.
1.6.5 Scope of the document
In addition to standard equipment, accessories kits and versions of the machine are described
in this document. Your machine may deviate from this document.
1.6.6 Means of representation
Icons in the text
The following means of representation (icons) are used to present the text more clearly:
Information on This Document 1
How to use this document 1.6
BiG X 630
Original operating instructions 150001258_06_en 15
This arrow characterizes an action step. Several arrows in a row identify a sequence of
actions to be performed step by step.
This icon identifies a prerequisite that has to be fulfilled to perform an action step or a
sequence of actions.
This arrow marks the intermediate result of an action step.
This arrow identifies the result of an action step or sequence of actions.
This bullet point identifies an enumeration. If the bullet point is intended, it identifies the
second level of the enumeration.
Icons in figures
The following icons can be used in illustrations:
Icon Explanation Icon Explanation
1
Reference sign for part
I
Position of a part (e.g. move from
position I to position II)
X
Dimensions (e. g. also W = width,
H = height, L = length)
Magnification of display detail
LH
Left side of machine
RH
Right side of machine
Direction of travel Direction of motion
Reference line for visible material Reference line for covered mater-
ial
Centre line Cable routes
Open Closed
Apply liquid lubricant (e.g. lubric-
ating oil)
Apply lubricating grease
Warning signs
Warnings of dangers are separated from the remaining text as warning signs and are identified
with a danger sign and signal words.
The warning signs must be read and the measures must be observed in order to prevent
personal injury.
Explanation of danger sign
This is the danger sign that warns of a risk of injury.
Please observe all notes marked with the danger sign in order to avoid injuries or death.
1 Information on This Document
1.6 How to use this document
16
BiG X 630
Original operating instructions 150001258_06_en
Explanation of signal words
DANGER
The signal word DANGER warns of a hazardous situation which will result in serious injuries
or death if the warning sign is ignored.
WARNING
The signal word WARNING warns of a hazardous situation which will result in serious injuries
or death if the warning sign is ignored.
CAUTION
The signal word CAUTION warns of a hazardous situation which will result in minor to
moderate injuries if the warning sign is ignored.
Example of a warning sign:
WARNING
Eye damage caused by flying dirt particles
When cleaning with compressed air, dirt particles are ejected at high speed and could get into
the eyes. Therefore eyes could be hurt.
Keep people away from the working area.
Wear personal protective equipment when performing cleaning work with compressed air
(e.g. eye protection).
Warnings of property damage/environmental damage
Warnings of property/environmental damage are separated from the remaining text and marked
with "Notice".
Example:
NOTICE
Gearbox damage due to low oil level
The gearboxes could be damaged when the oil level is too low.
Check gear oil level at regular intervals and top up oil, if necessary.
Check gear oil level approx. 3 to 4 hours after the machine has been switched off. Check
oil level only when machine is in horizontal position.
Notices with information and recommendations
Additional information and recommendations for trouble-free and productive operation of the
machine are separated from the remaining text and marked with “Information”.
Example:
INFO
Each safety sign is provided with an order number and can be ordered directly from the
manufacturer or from an authorised specialist dealer.
Information on This Document 1
How to use this document 1.6
BiG X 630
Original operating instructions 150001258_06_en 17
1.6.7 Conversion table
The following table can be used to convert metric units into US units.
Size SI units (metric) Factor Inch-pound units
Unit name Abbrevi-
ation
Unit name Abbrevi-
ation
Area Hectare ha 2.47105 Acre acres
Volume flow Litres per minute L/min 0.2642 US gallons per
minute
gpm
Cubic metres
per hour
m³/h 4.4029
Force Newton N 0.2248 Pound force lbf
Length Millimetre mm 0.03937 Inch in.
Metre m 3.2808 Foot ft.
Power Kilowatt kW 1.3410 Horsepower hp
Pressure Kilopascal kPa 0.1450 Pounds per
square inch
psi
Megapascal MPa 145.0377
bar (non-SI) bar 14.5038
Torque Newtonmeter Nm 0.7376 pound-foot or
foot-pound
ft∙lbf
8.8507 pound-inch or
inch-pound
in∙lbf
Temperature Degrees Celsius °C °Cx1.8+32 Degrees
Fahrenheit
°F
Velocity Metres per
minute
m/min 3.2808 Feet per minute ft/min
Metres per
second
m/s 3.2808 Feet per second ft/s
Kilometres per
hour
km/h 0.6215 Miles per hour mph
Volumes Litres L 0.2642 US gallon US gal.
Millilitre ml 0.0338 US ounce US oz.
Cubic centi-
metre
cm³ 0.0610 Cubic inch in³
Weight Kilogram kg 2.2046 Pound lbs
2 Safety
2.1 Intended use
18
BiG X 630
Original operating instructions 150001258_06_en
2 Safety
2.1 Intended use
This machine is a self-propelled forage harvester and is used to chop crops.
The crops designated for the intended use of this machine in conjunction with
• a KRONE XCollect are harvested thick-stemmed forage plants, e.g. maize plants,
• a KRONE EasyCollect are harvested thick-stemmed forage plants, e.g. maize plants,
• a KRONE XDisc are mown stalk and leaf crops,
• a KRONE EasyFlow collected stalk and leaf crops,
• a header for smallwood crops from cut groves.
The machine is designed exclusively for use in agriculture and may only be used when
• all safety devices are available according to the operating instructions and are located in the
protective position.
• all safety instructions of the operating instructions have been observed and complied with,
both in chapter “Basic safety instructions”, see Page19, and directly in the chapters of the
operating instructions.
The machine may be used only by people who satisfy the personnel qualification requirements
designated by the machine manufacturer, see Page19.
These operating instructions are part of the machine and must therefore be at hand when the
machine is in use. The machine may be operated only when the operator has received training
and in compliance with these operating instructions.
If the machine is used for applications which are not described in these operating instructions,
this may result in serious injuries or death and damage to the machine and other property.
Unauthorised modifications to the machine may affect the properties of the machine or disrupt
the proper operation. For this reason, unauthorised modifications shall exclude any liability of
the manufacturer for consequential damage.
The intended use shall also include the adherence to the operating, maintenance and repair
conditions set by the manufacturer.
2.2 Reasonably foreseeable misuse
Any use beyond the intended usesee Page18 is regarded as improper use and is therefore
misuse according to the Machinery Directive. The manufacturer is not liable for damage
resulting from this, the user alone bears the risk.
Such misuse is for example:
• Processing of crops which are outside the intended use of the machine,see Page18
• Transport of people
• Transport of goods
• Exceeding the permitted technical gross weight
• Non-compliance with the safety labels on the machine and safety notes in the operating
instructions
• Performing troubleshooting, setting, cleaning, repair and maintenance work contrary to the
information in the operating instructions
• Unauthorised modifications to the machine
• Attachment of unauthorised or unapproved additional equipment
• Use of spare parts which are not KRONE original spare parts
• Stationary operation of the machine
Unauthorised modifications to the machine may affect the properties of the machine or disrupt
proper operation. For this reason, unauthorised modifications will exclude any liability of the
manufacturer for consequential damage.
Safety 2
Service life of the machine 2.3
BiG X 630
Original operating instructions 150001258_06_en 19
2.3 Service life of the machine
• The service life of this machine depends on its proper operation and maintenance as well
as the operating and harvesting conditions.
• By heeding the instructions and information in these operating instructions, permanent
operational readiness and a long service life of the machine can be achieved.
• After each operating season, inspect the entire machine for wear and other damage.
• Replace damaged and worn components before recommissioning the machine.
• Carry out a full technical inspection of the machine after five years of machine operation
and make a decision on further machine usage taking the results of this inspection into
account.
• Theoretically, the service life of this machine is unlimited as all worn or damaged
components can be replaced.
2.4 Basic safety instructions
Non-compliance with the safety instructions and warnings
Non-compliance with the safety instructions and warnings may result in injuries and damage to
the environment and property.
2.4.1 Importance of operating instructions
The operating instructions are an important document and a part of the machine. They are
intended for the user and contain information that is relevant to safety.
Only the procedures specified in the operating instructions are safe. If the operating instructions
are not followed, there is a risk of serious or even fatal injuries.
Prior to using the machine for the first time, read and observe the "Basic safety notices"
completely.
Prior to starting work, read and observe the respective sections in the operating instructions
too.
Keep the operating instructions easily accessible for the machine user at all times.
Hand over the operating instructions to subsequent users.
2.4.2 Personnel qualification of the operating personnel
If the machine is not used properly, people may be seriously injured or killed. To avoid
accidents, each person who works with the machine must satisfy the following minimum
requirements:
• He is physically capable of controlling the machine.
• He can work safely with the machine in accordance with these operating instructions.
• He understands the method of operation of the machine within the scope of his work and
can identify and avoid the dangers associated with the work.
• He has read the operating instructions and can implement the information in the operating
instructions accordingly.
• He is familiar with driving vehicles safely.
• For road travel he has adequate knowledge of the highway code and has the stipulated
driving licence.
2 Safety
2.4 Basic safety instructions
20
BiG X 630
Original operating instructions 150001258_06_en
2.4.3 Personnel qualification of the technicians
If the work (assembly, conversion, modification, extension, repairs, retrofitting) is performed
improperly on the machine, people may be seriously or fatally injured. To avoid accidents,
everyone who performs work according to these instructions must meet the following minimum
requirements:
• Qualified professional, with relevant training.
• Capable of assembling the (partially) disassembled machine according to the assembly
instructions provided by the manufacturer.
• He is capable, e.g. by attending a training course, of extending, modifying or repairing the
function of the machine according to the relevant instructions provided by the manufacturer.
• He has read the operating instructions and can implement the information in the operating
instructions accordingly.
• Ability to perform the work safely according to these instructions.
• Understands the mode of operation of the work to be performed and the machine and is
able to identify and avoid risk in carrying out the necessary work.
• Has read these instructions and is able to implement the information explained in these
instructions accordingly.
2.4.4 Children in danger
Children are not in a position to assess dangers and behave unpredictably.
Thus children are particularly at risk.
• Children are especially at risk when climbing up and down the machine.
• There is no possibility to secure children sufficiently on the self-propelled machine.
• Vibrations can be particularly harmful to children's bodies.
• Children may initiate dangerous movements of the machine.
Never take children on the self-propelled harvester.
Keep children away from the machine.
Keep children away from consumables.
Make sure that there are no children in the danger zone, especially when starting and
triggering machine movements.
2.4.5 Connecting the machine
If headers or trailers not connected properly to the forage harvester, serious accidents could be
caused.
When connecting, observe the following operating instructions:
• the header operating instructions
• the trailer operating instructions
• the machine operating instructions
• the universal shaft operating instructions
Follow the coupling instructions:
• for headers see Page204 und see Page222.
• for trailers see Page265
Observe the changed driving behaviour of the combination.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
