Powerwave Technologies OS-1933-E0-003 User manual

Brand: Powerwave Technologies

Model: OS-1933-E0-003

Type: User manual

This manual is also suitable for

E675JS0105

044-05243 Rev A June 2008

OUTDOOR BOOSTER SYSTEM

INSTALLATION AND SERVICE MANUAL

MCPA OUTDOOR SYSTEM

OS-1933-E0-003

Installation and

Powerwave Technologies, and the Powerwave logo are registered trademarks.

This Powerwave product is intended only for installation in a RESTRICTED ACCESS LOCATION and

this Powerwave product is designed to operate within the normal operating (typical operating) ranges

or conditions specified in this document. Operation of this equipment beyond the specified ranges in

this document may cause:

1.Spurious emissions that violate regulatory requirements.

2.The equipment to be automatically removed from service when maximum thresholds are exceeded.

3.The equipment to not perform in accordance with its specifications.

It is the operator’s responsibility of the operator to ensure this equipment is properly installed and

operated within Powerwave operating specifications to obtain proper performance from the equipment

and to comply with regulatory requirements.

For PERMANENTLY CONNECTED EQUIPMENT, a readily accessible disconnect device shall be

incorporated in the building permanent wiring.

OS-1933-E3-003 Revision Record

044-05243 Rev A i

Revision Record

Revision Date of Change Reason for Change

Rev A June 2008 Initial Release

OS-1933-E3-003 Revision Record

ii 044-05243 Rev A

This page intentionally left blank

044-05243 Rev A vii

Preface

Warning, Cautions, and Notes

Warnings, Cautions, and Notes are found throughout this manual where applicable. The associated icons in

warnings and cautions are used to quickly identify a potential condition that could result in the consequences

described below if precautions are not taken. Notes clarify and provide additional information to assist the

user.

WARNING: The warning symbol means danger. You are in a situation that could cause bodily

injury or death. Before you work on any equipment, be aware of the hazards involved with elec-

trical and RF circuitry and be familiar with standard practices for preventing accidents.

CAUTION: The caution symbol means the potential exists for equipment damage or loss of

data.

NOTE: Notes contain helpful suggestions or references to material not covered in the document.

Safety

Any personnel involved in installation, operation, or service of units included in a Powerwave MCPA Outdoor

System must understand and follow the points below:

❑Units supplied from the mains must be connected to grounded outlets and in conformity with the local

prescriptions.

❑For outdoor use, the power cord should meet at least IP65 encapsulation requirements. Do not turn

the main power on until you are ready to commission the equipment.

❑Power supply units supplied from the mains contain dangerous voltage that can cause electric shock.

Disconnect the mains prior to any work in such a unit. Local regulations are to be followed when

servicing such units. Only authorized service personnel are allowed to service units while the mains

are connected.

Safety OS-1933-E3-003

viii 044-05243 Rev A

This page intentionally left blank.

OS-1933-E3-003 Table of Contents

044-05243 Rev A ix

TABLE OF CONTENTS

Warning, Cautions, and Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Chapter 1 - Product Description

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Scope of Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

MCPA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

RF Conditioning Unit (RFCU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Controller Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Power System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

TMA Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Ethernet Web Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Form-C Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

External Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Chapter 2 - Installation

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Site Survey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Unpacking and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Electrical Service Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

RF Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Form-C Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

External Alarms (EA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

MCPA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Power system Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

RFCU Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Chapter 3 - Operation

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Initial Start-Up Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

OS System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Configure PC for Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Activate Sectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Activate Rectifier Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Activate TMA Channels (2 per Sector) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Adjust LNA Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Adjust Tx Gain. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Adjust VSWR Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Activate External Alarm Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Status Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

MCPA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Controller Web Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

System – Download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Software Download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

System – Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

Status – Static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

Status – Dynamic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

Table of Contents OS-1933-E3-003

x044-05243 Rev A

MCPA APC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

MCPA Front Panel Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

Rectifiers – Installed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

Rectifiers – Comm Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

Rectifiers – Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

Status – Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

User. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

Alarm Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

Alarm Status Indicators (front panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

PC Interface (front panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

Ethernet Interface (front panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

Ethernet Web Page Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-17

Ethernet Interface (rear panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

Form C/External Alarm Interface (rear panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-17

Form-C Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

Alarm 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

Alarm 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

Alarm 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18

Alarm 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18

Alarm 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18

External Alarm Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18

Chapter 4 - Maintenance

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Cleaning Air Inlets/Outlets/Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

MCPA does not have a solid green LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Rectifier Module with a Red LED or Individual Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

RECT ALL COMM Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Rectifier Voltage Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Fans Not Operating – . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

RFCU Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

RF Performance Issues -. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Field Replaceable Parts and Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

MCPA Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Rectifier Module Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6

Controller Module Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

RF Conditioning Unit (RFCU) Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Fan Assembly Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Air Filter Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Power System Fuse Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

Chapter 5 - Specifications and Drawings

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

OS-1933-E3-003 Table of Contents

044-05243 Rev A xi

List of Figures

1-1 Outdoor System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

1-2 Outdoor System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

1-3 Outdoor System, Front View, Door Open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

1-4 Outdoor System, Rear View, Door Open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

1-5 MCPA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

1-6RF Conditioning Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

1-7 Control Module Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

1-8 Power System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

2-1 AC Power Connections Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2-2 Interface Bulkhead RFCU Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

2-3 Controller Module Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

2-4 External Alarms and Form-C Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

2-5 MCPA Quarter-Turn Fasteners, Status Indicator, and RF Power Switch . . . . . . . . . . . . . . . . . . . . . . 2-8

2-6 MCPA 21-Pin D-Sub Connector Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

3-1 Network Configuration and Controller Module Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

3-2 Network Connections Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

3-3 Local Area Connection Properties Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

3-4 Internet Protocol (TCP/IP) Properties. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

3-5 Setting the IP Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

3-6 Enable the Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

3-7 Rectifier Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

3-8 MCPA Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

3-9 Controller Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

3-10 Download Web Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

3-11 Select File to Download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

3-12 Download Now . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

3-13 Download In Progress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

3-14 Download Complete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

3-15System - Configuration page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

3-16 Status - Static page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

3-17 Status - Dynamic page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

3-18 Status - Alarms page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

3-19 User page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

4-1 MCPA Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

4-2 Rectifier Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

4-3 Controller Module Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

4-4 RF Conditioning Unit Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

4-5 Fan Assembly Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

4-6 Air Filter Removal, Cleaning, and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

4-7 Fuse removal and replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

5-1 Outdoor System Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

5-2 Installation Example One . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

5-3 Installation Example Two . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

5-4 Installation Example Three . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Table of Contents OS-1933-E3-003

xii 044-05243 Rev A

List of Tables

1-1 Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

2-1 Unpacking and Inspection Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2-2 Averaged AC and DC Current Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2-3 Materials Required for System Installation, Not Supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

2-4 Tools Needed for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

2-5 AC Power Connection Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

2-6 OS System RF Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2-7 Form-C Alarms Connection Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

2-8 Form-C Alarm Terminal Block Relay Connections and Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

2-9 External Alarms Connection Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

2-10 MCPA Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

2-11 Rectifier Module Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

2-12 Rectifier Module Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

2-13 RFCU Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

3-1 Initial Start-Up Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3-2 Configure PC for Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

3-3 Activate Sectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

3-4 Activate Rectifier Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

3-5 Activate TMA Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

3-6 Adjust LNA Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

3-7 Adjust Tx Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

3-8 Adjust VSWR Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

3-9 Activate External Alarm Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

3-10 Status Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

3-11 Rectifier Status Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

3-12 MCPA Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

3-13 Downloading Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

3-14 LED Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

3-15 Ethernet Web Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

4-1 Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4-2 MCPA - no solid green LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

4-3 Field Replaceable System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

4-4 MCPA Removal and Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

4-5 Controller Module Removal and Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

4-6 Controller Module Removal and Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

4-7 RF Conditioning Unit (RFCU) Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

4-8 Fan Assembly Removal and Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

4-9 Air Filter Cleaning Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

4-10 60-Amp Fuse Removal and Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

4-11 15-Amp Fuse Removal and Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

5-1 Outdoor System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

5-2 Weights and Measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

044-05243 Rev A 1-1

Chapter 1

Product Description

Introduction

This manual provides information and procedures for installation, operation, and maintenance of the

OS-1933-E0-003 Multi-Carrier Power Amplifier (MCPA) Outdoor Booster System.

Scope of Manual

This manual is intended for use by service technicians familiar with similar types of equipment. It contains

service information required for the equipment described and is current as of the printing date. Changes which

occur after the printing date may be incorporated by a complete manual revision or alternatively as additions.

General Description

The outdoor system (OS), shown in Figures 1-1 through 1-4, is a three-way system operating in a 60MHz

transmit frequency band from 1930 to 1990MHz with an instantaneous bandwidth of any 60MHz within the

operating transmit band and an uplink frequency range of 1850 to 1910 MHz.

The OS has a sturdy aluminum IP55 rated cabinet with front and rear locking hinged doors equipped with

intrusion alarms. The door latches are 1/4 turn and require a 10 mm hex socket wrench or nut driver to open

and close. The doors can be secured with a padlock with a 1/2 inch maximum shank diameter. The front and

rear doors contain removable, washable air filters.

Bolt inserts located on the cabinet side and bottom panels are for mounting the OS to a secure fixed location.

RF connections are located on the interface bulkhead plate at the bottom rear of the cabinet. External power,

communications, and alarm cables are routed through access holes located adjacent to the bulkhead. Cabinet

ground is also located next to the interface bulkhead.

The OS system provides three forms of alarm reporting; Form-C contact closure, ethernet (web page), and

wireless modem.

Major features of the OS cabinet include the following:

MCPA

The MCPA module, shown in Figure 1-5, is a 1900 MHz RF amplifier. The MCPAs operational features include

a front panel RF OFF/ON/RESET switch and a multicolored LED indicator to display system status. MCPA

faults are reported via the status alarm web page.

RF Conditioning Unit (RFCU)

The RF Conditioning Unit (RFCU) shown in Figure 1-6 combines up to four separate BTS feeds; two duplexed

and two simplexed. The RFCU combines, attenuates, and conditions the RF signals. If a critical system failure

occurs, the RFCU places the system into bypass mode. The RFCU has two Low Noise Amplifier Units with

adjustable gain, each located between the output and input duplexer on the RX path and the diversity RX path.

Performance of the RFCU is monitored and reported via the Ethernet web pages. Faults from the RFCU are

mapped to Form-C and optional wireless modem alarms.

❑Up to three MCPAs. (one per sector, up to 160W)

❑Three RF Conditioning Units (RFCU).

❑One Control Module

❑One power system containing up to four rectifier modules.

❑Two variable-speed fan assemblies, front and rear doors.

OS-1933-E3-003 Scope of Manual

1-2 044-05243 Rev A

Controller Module

The Controller Module shown in Fig. 1-7 provides control and monitoring of the OS operation through two

Ethernet ports, Form-C alarms, external alarm inputs and LED status indicators. Status and configuration

details are available through Ethernet web pages.

Power System

The power system shown in Figure 1-8, contains up to four +28.5 VDC plug-in 1300 watt rectifier modules.The

rectifier modules convert the system AC input power to supply +28.5 VDC to each MCPA and the Controller

Module. Performance of the power system is monitored and reported via the Ethernet web pages. Power

system faults are mapped to Form-C and optional wireless modem alarms

TMA Supply

The two Rx channels per sector provide DC power via Bias-Ts to external Tower Mounted Amplifier (TMA)

modules. Each channel is programmable via the Ethernet web pages. The Control Module monitors and

reports DC current. Loss of current or excessive current generates a fault and disables the channel. All fault

modes are continuously monitored for fault auto recovery. TMA power is provided independent of the bypass

status.

Fans

The system is cooled by two variable speed DC fans, located on the front and rear doors, providing air flow

through the booster cabinet. The fans draw ambient air through a filter mounted in the front panel vents and

send heated air out the filter mounted in the rear panel. The variable speed fans are dependant on the MCPA,

power system, Controller Module temperature sensors, and door intrusion status. Fan operation is disabled

when any door opens. Pulling out the door intrusion switch plunger emulates a door closure and activates the

fan operation. The variable speed fans maintain adequate cooling by operating at the slowest possible speed.

All temperature sensors are monitored by the Control Module and the hottest device controls the fan speed.

Fan speed increases or decreases by one step per one minute.

Ethernet Web Pages

The Ethernet web pages are accessible via the front panel Ethernet port on the Controller Module. Use a web

browser to view the following pages:

Form-C Alarms

The Form-C method includes four alarm levels detailing alarm severity as follows:

❑Status/Static - Displays current firmware and user controllable configurations.

❑Status/Dynamic - Displays the operator performance of the system in real time.

❑Status/Alarm - Displays the status of all the individual alarm parameters.

❑User - Displays Unique I.D. about this system and password entries.

❑System/Configuration - Displays and allows modification to system configurations.

❑System/Download - Firmware related interface.

❑Minor - System requires maintenance.

❑Major - System operating but not at optimum performance.

❑Critical (one per sector, three total)- System disabled and bypass active due to a loss

of Tx or Rx.

Scope of Manual OS-1933-E3-003

044-05243 Rev A 1-3

External Alarms

The OS booster is capable of monitoring and reporting external Form-C alarms. Four channels are provided

and each channel is programmed via the Controller Module for NO or NC conditions. For example, NO will

fault when shorted to Common (C) and NC will fault when open to Common (C).The four channels are mapped

to Form-C alarm outputs configured as such via the Ethernet web pages.

(1) Could be critical and bypass if both Rx channels are faulted.

(2) If enabled.

Table 1-1 Faults

Control Module Display X = Form-C

Fan XX Fault FT(front)/

RT(frear)

Minor

RFCU Fault (3) Sector 1 - 3 Critical

Bypassx DC Fault (3) Sector 1 - 3 Critical

LNA 1 Fault

LNA 2 Fault

Sector 1 - 3 Major (1)

Rect Comm Fault Minor

Rect VAC High Major

Rect VAC Low Major

Rect VDC High Major

Rect VDC Low Major

Rect Current Limit Major

Rect Fault (not all) Major

Rect Fault (all) Critical

No MCPA Sector 1 - 3 Critical

MCPAX VSWR Sector 1 - 3 Critical

MCPAX Loop Sector 1 - 3 Critical

MCPAX Ovr Pwr Sector 1 - 3 Critical

MCPAX Hi Temp Sector 1 - 3 Critical

MCPAXInt DC Sector 1 - 3 Critical

MCPAX Ext DC Sector 1 - 3 Critical

Ext Alarm0 Major (2)

Ext Alarm1 Major (2)

Ext Alarm2 Major (2)

Ext Alarm3 Major (2)

TMA1 Hi Current Major (1)

TMA 1 Lo Current Major (1)

TMA 2 Hi Current Major (1)

TMA 2 Lo Current Major (1)

OS-1933-E3-003 Scope of Manual

1-4 044-05243 Rev A

Figure 1-1 Outdoor System Block Diagram

PA0

Attenuator

Section

Controller

Ethernet

Interface

BTS TX1/RXm

BTS TX2/RXd

ANT. RXd

ANT. TX/RXm

Rectifier

Shelf

(x4)

PA Control I/O

RFCU Control I/O

Power and

Control Lines

DC Power

External Alarm

Inputs

Ext. Alarm Info.

Form-C

Interface

Form-C Data Out

VSWR

RFCU_Sector_0

PA1

Input

Filtering

Section

Output

Filtering

Section

Attenuator

Section

RFCU_Sector_1

PA2

Attenuator

Section

RFCU_Sector_2

SECTOR_0 RF

Interface

SECTOR_1 RF

Interface

SECTOR_2 RF

Interface

BTS TX3

BTS TX4

BTS TX1/RXm

BTS TX2/RXd

ANT. RXd

ANT. TX/RXm VSWR

BTS TX3

BTS TX4

BTS TX1/RXm

BTS TX2/RXd

ANT. RXd

ANT. TX/RXm VSWR

BTS TX3

BTS TX4

Input

Filtering

Section

Output

Filtering

Section

Input

Filtering

Section

Output

Filtering

Section

Bypass

Switching

Bypass

Switching

Bypass

Switching

LNA

Section

LNA

Section

LNA

Section

Input Power, I/O_1,

and I/O_2

Fan Assy. (x2)

Fan Control

Internal User

Interface Panel

Rear Interface

Panel

Ethernet

AC Input

Figure 1-2 Outdoor System

Front Rear

“A” locations my be used as lifting points.

Use minimum of two eyebolts.

Scope of Manual OS-1933-E3-003

044-05243 Rev A 1-5

Figure 1-3 Outdoor System, Front View, Door Open

Figure 1-4 Outdoor System, Rear View, Door Open

Power

System

MCPAs

Controller Module

Intrusion

Alarm Switch

Fan

RF Conditioning

Unit(s)

(Rectifier Modules)

RF Input

and Output

Interface

Ground

Power/Alarm

Fan

AC Input

Intrusion

Alarm

Switch

Cable Access

External Alarms Form-C Alarms

Terminal

Panel

OS-1933-E3-003 Scope of Manual

1-6 044-05243 Rev A

Figure 1-5 MCPA

Figure 1-6 RF Conditioning Unit

Figure 1-7 Control Module Front Panel

Front Rear

Rear

Front

Scope of Manual OS-1933-E3-003

044-05243 Rev A 1-7

Figure 1-8 Power System

Rectifier 0

Rectifier 1

Rectifier 2

Rectifier 3

OS-1933-E3-003 Scope of Manual

1-8 044-05243 Rev A

This page intentionally left blank

044-05243 Rev A 2-1

Chapter 2

Installation

Introduction

This chapter provides unpacking, inspection, installation instructions, and recommendations for installing the

OS-1933-E3-003 Multi-Carrier Power Amplifier (MCPA) Outdoor Booster System.

• Review this chapter prior to equipment installation.

• Review any government and local codes applicable to this installation.

• Read the instructions in Chapter 3 before operating the equipment.

Site Survey

Powerwave recommends that a site survey be performed prior to equipment ordering or installation to reduce

or eliminate installation and turn-on delays. Note power plant capacity, cooling, RF/AC cabling/breaker

requirements, clearances for proper cooling airflow and maintenance access. System dimensions and weights

are listed in Chapter 5, Table 5-2.

Unpacking and Inspection

Perform the steps in Table 2-1: to unpack and inspect the Outdoor System (OS).

If the equipment is damaged, a claim should be filed with the carrier when the extent of any damage is

assessed. Contact the factory for a return material authorization (RMA). Refer to Chapter 4.

Electrical Service Recommendations

The base station AC supply to each OS should have a single phase UL listed AC circuit breaker rated at least

30 amps. The AC supply also requires UL listed external surge protection rated 2500 Vpk or less for 150 to 300

VAC mains installed in accordance with Article 285 of ANSI/NFPA or applicable local codes.

Table 2-2 lists the OS AC and DC current loads.

Table 2-1: Unpacking and Inspection Instructions

Step Action

1Open the containers and carefully remove the cabinet, MCPAs, RFCUs and Rectifier Modules

2 Visually inspect the outdoor system for shipping damage. Check for evidence of water damage,

bent or warped chassis, loose screws or nuts, or extraneous packing material in connectors.

Inspect the equipment in the presence of the delivery person if possible

3Retain all packing material that can be reused to return components to the factory

Table 2-2 Averaged AC and DC Current Loads

Number of

MCPAs

AC Current

Max at 180

VAC

DC Current

(max)

DC Current

(Typical)

AC Current

(Typical)

@ 220 VAC

19.0 amps 49 amps 46 amps 6.9 amps

2 16.2 amps 88 amps 82 amps 12.3 amps

323.7 amps 127 amps 113 amps 17.7 amps

OS-1933-E3-003 Installation Instructions

2-2 044-05243 Rev A

Installation Instructions

CAUTION: After commissioning, ensure that all power cable and control cables are properly sealed to pre-

vent moisture and contaminants from entering the cabinet.

The outdoor system is designed for installation in an exterior location. The outdoor system must be installed in

a designated location that permits access to the lower rear of the cabinet for connection of AC power, RF,

communications, and alarm cables. In hot climate environments, shading of the outdoor system is

recommended to reduce external heating of the cabinet.

Verify sufficient space is available in front of the cabinet to remove and replace the MCPA, RFCU, and rectifier

modules and allow free movement of ambient air through the front panel air intake and rear panel exhaust

vents. The front door must swing open at a 135 degree angle to allow removal of the MCPAs. Cabinets must

have at least 11 inches clearance from the mounting surface if mounted on the left side (facing unit) to allow for

door swing. Recommended minimum clearances for the front of the cabinet is 36 inches and 20 inches for the

rear of the cabinet. Refer to Tables 2-3 and 2-4 respectively for the materials and tools required for a typical

outdoor system installation. Refer to Chapter 5 for system dimensions and typical mounting examples.

* Specific requirements depending on application.

Table 2-3 Materials Required for System Installation, Not Supplied

Item Materials Needed Where Used Approx.

Length (Each)

Quantity Per

Cabinet

110 AWG AC power cable rated

for 24A minimum

From AC breaker panel to cabi-

net

As needed 1

1 Tie wraps (152 mm or 203

mm)

Cable dressing As needed

2Unistrut, 1 5/8 “(41 mm) System mounting As needed

3 Terminal Lugs, 2-Hole, 3/4”

(19 mm) Centers. M8 bolt, 60

mm Length, Must be UL listed

(ZMVV).

Cabinet ground studs 1

4M10x1.75 hex bolt System mounting 6 min / 12 max

5 10 mm flat washer System mounting 6 min / 12 max

610 mm lock washer System mounting 6 min / 12 max

7 0.5 inch foam semi-rigid coax

(N male to N male, 7/16 DIN)*

RF input to system and RF

output from system to antenna

jumper

1.5 M -12 M 2

8Weatherproofing materials RF, power, and alarm connectors As needed

Page is loading ...

Powerwave Technologies OS-1933-E0-003 User manual

Brand: Powerwave Technologies

Model: OS-1933-E0-003

Type: User manual

This manual is also suitable for

E675JS0105

Download PDF

report

Powerwave Technologies OS-1933-E0-003 User manual

This manual is also suitable for

Powerwave Technologies OS-1933-E0-003 User manual

Related papers

Other documents