Cadet Manufacturing 68070 Installation guide

Brand
Cadet Manufacturing
Model
68070
Type
Installation guide

This manual is also suitable for

Cadet Manufacturing 68070 allows you to mount Cadet heaters on walls that do not have the correct wall can or if the old wall can needs to be replaced. It is compatible with any C, CM, or CB series heater, as well as any CT series heater. Cadet Manufacturing 68070 comes with screws for easy installation, and it can be painted to match your décor. It is essential to remember that electrical work can be hazardous, and if you are uncomfortable working with electrical appliances, it is best to consult a qualified electrician.

Cadet Manufacturing 68070 allows you to mount Cadet heaters on walls that do not have the correct wall can or if the old wall can needs to be replaced. It is compatible with any C, CM, or CB series heater, as well as any CT series heater. Cadet Manufacturing 68070 comes with screws for easy installation, and it can be painted to match your décor. It is essential to remember that electrical work can be hazardous, and if you are uncomfortable working with electrical appliances, it is best to consult a qualified electrician.

If you are uncomfortable working with electrical appliances, unable to
follow these guidelines, or do not have the necessary equipment, con-
sult a qualified electrician.
1. WITH THE POWER OFF, remove the old heater and wall can,
leaving existing wiring intact. Note: Make sure there is enough
wire to reach through the new wall can knockout and extend at
least 6 inches into the wall can interior. (Never use the wall stud
cavity as a place to splice wires without an approved junction box).
2. Position adapter plate on wall. Line up holes in adapter plate with a
wall stud, covering the old opening (See Figure A or B).
3. Install adapter plate with screws (not provided). Do not use nails.
Make sure at least one side of the adapter plate – upper and lower
– is screwed to a wall stud. The screws should be sufficiently
snug, but avoid over tightening. If you are installing a narrow
adapter plate (SAMA or SAMW) or installing the adapter plate
on a wall with studs that are not on 16 inch centers, you may
use 2 wall anchors.
4. Remove a knockout from the heater wall can closest to the supply
wires. Install an approved strain relief connector (not included) in
the knockout.
5. Pull at least 6 inches of the house wiring through the strain relief
connector into the wall can. Tighten the strain relief connector.
6. Insert the wall can into the hole and mount the wall can to the wall
stud with screws through the side of the wall can.
7. Attach the wall can to the adapter plate with the screws provided
through the top and bottom lips of the wall can. Two screws are
required to provide proper grounding of the adapter plate.
8. Connect the grounding wire in the house supply wire to the ground
wire or screw in the wall can.
9. Install the heater according to the heater instructions.
10. Adapter plate may be painted with 100% acrylic latex to match
décor.
Models: CAMW CAMA
SAMW SAMA
CTAMW CTAMA
Tools Required:
Phillips Screwdriver
Straight Screwdriver
Wire Strippers
Drill
Drill Bits
Utility Knife
Hammer
Chisel
4 Wall Fasteners
1 Strain Relief
Wire Connectors
Screws
For use with any CT series heater.
INSTALLATION INSTRUCTIONS
Metal Adapter Plates
SAVE THESE INSTRUCTIONS
INSTALLATION INSTRUCTIONS
TEL: 360-693-2505 Fax: 360-694-8668 P.O. Box 1675 Vancouver, WA 98668-1675
IMPORTANT INSTRUCTIONS
©2006 Cadet Manufacturing Co. Printed in U.S.A. 08/06 #720014
Figure A
Before mounting the adapter, read heater installation instructions for heater placement minimum
clearances.
WARNING
Turn the electrical power off at the electrical panel board (circuit breaker or fuse box) and lock or
tag the panel board door to prevent someone from turning on power while you are working on the
heater. Failure to do so could result in serious electrical shock, burns, or possible death.
For use with any C, CM or CB series heater.
  • Page 1 1
  • Page 2 2

Cadet Manufacturing 68070 Installation guide

Brand
Cadet Manufacturing
Model
68070
Type
Installation guide
This manual is also suitable for

Cadet Manufacturing 68070 allows you to mount Cadet heaters on walls that do not have the correct wall can or if the old wall can needs to be replaced. It is compatible with any C, CM, or CB series heater, as well as any CT series heater. Cadet Manufacturing 68070 comes with screws for easy installation, and it can be painted to match your décor. It is essential to remember that electrical work can be hazardous, and if you are uncomfortable working with electrical appliances, it is best to consult a qualified electrician.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents