WITH THE POWER OFF, remove the old heater and wall
can, leaving existing wiring intact. Note: Make sure there
is enough wire to reach through the new wall can knockout
and extend at least 6” into the wall can interior. (Never use
the wall stud cavity as a place to splice wires without an
approved junction box).
Position adapter plate on wall. Line up holes in adapter plate
with a wall stud, covering the old opening (See figure A or B).
Install adapter plate with screws (not provided). Do not
use nails. Make sure at least one side of the adapter plate –
upper and lower – is screwed to a wall stud. The screws
should be sufficiently snug, but avoid over tightening. If you
are installing a narrow adapter plate (SAMA or SAMW)
or on a wall with studs that are not on 16 inch centers,
you may use 2 wall anchors.
Remove a knockout from the heater wall can closest to
the supply wires. Install an approved strain relief connector
(not included) in the knockout.
Pull at least 6 inches of the house wiring through the strain
relief connector into the wall can. Tighten the strain relief
connector.
Insert the wall can into the hole and mount the wall can to
the wall stud with screws through the side of the wall can.
Attach the wall can to the adapter plate with the screws
provided through the top and bottom lips of the wall can.
Two screws are required to provide proper grounding of
the adapter plate.
Connect the grounding wire in the house supply wire to
the ground wire or screw in the wall can.
Install the heater according to the heater instructions.
Adapter plate may be painted with 100% acrylic latex to
match décor.
2()/5
CAMW CAMA SAMW SAMA
For use with any C, CS, CM, CE or CB
series heater.
CTAMW CTAMA
For use with any CT, CST series heater.
! "
Phillips Screwdriver
Straight Screwdriver
Wire Strippers
Drill
Drill Bits
Utility Knife
Hammer
Chisel
4 Wall Fasteners
1 Strain relief connector
!! !"!
!!!
-+74)
$
!7416,))/)'64-'%/329)42**%66,))/)'64-'%/3%1)/&2%4('-4'7-6&4)%.)424*75)&2:%1(/2'.
246%+6,)3%1)/&2%4((2246234)8)16520)21)*4206741-1+21329)49,-/);27%4)924.-1+21
6,),)%6)4%-/74)62(252'27/(4)57/6-15)4-275)/)'64-'%/5,2'.&7415243255-&/)()%6,
)*24)02716-1+6,)%(%36)44)%(,)%6)4-156%//%6-21-15647'6-215*24,)%6)43/%')0)16
0-1-070'/)%4%1')5
1
#! !"!
cadetheat.com Tel: 360-693-2505 P.O. Box 1675 Vancouver, WA 98668-1675
©2014 Cadet Printed in U.S.A. 12/14 #720014
Metal Adapter Plates
Installation Instructions
http://www.cadetheat.com/products/wall-heaters/com-pak
http://www.cadetheat.com/products/wall-heaters/com-pak-twin
-
1
-
2
Cadet SAMA Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Cadet CAMW Owner's manual
-
-
-
-
Cadet CE163TW Owner's manual
-
-
-
-
-
Other documents
-
Cadet Manufacturing 68070 Installation guide
-
Cadet Manufacturing 67506 Installation guide
-
Williams AC2030 Owner's manual
-
Cadet Manufacturing 13170 Installation guide
-
-
Weil-McLain ECO110 Owner's manual
-
Williams 3509622A Owner's manual
-
-
-
