1(10)
Copyright © 2014 Westermo Teleindustri AB
ADSL-350 Firmware
Release Notes
Version 1.7.6.20
Version 1.7.6.20 (Build-date: 2020-05-20)
General
• This release includes enhancements and bug fixes.
New Feature(s)
• None.
Enhancement(s)
• Added VDSL without G.INP mode.
• Added PPPoE Local Address support.
• Security:
o General improvements.
o TLS upgrade.
• Web: Improved Javascript error handling on various web pages.
• VRRP: Added ability to add polling source address.
• IPsec: Added ability to add polling source address.
• PPP: Updates to improve connection establishment speed.
• Reduced start up time detection of Ethernet connection.
Bug Fixes
• IPsec: Individual tunnel restart no longer causes all tunnels to restart.
• Resolved issue were alias IP address was not enabled when configuration reset switch
pressed.
Note(s)
• None
Model
ADSL-350
Date
2019-05-27
Version
1.7.6.20
Tools
N/A
2(10)
Copyright © 2014 Westermo Teleindustri AB
Version 1.7.6.19 (Build-date: 2019-03-22)
General
• This release includes enhancements and bug fixes.
New Feature(s)
• None.
Enhancement(s)
• DHCP: Added custom default route option.
• DHCP added relay functionality.
• RIP: Added option to disable advertising default route.
• Improved logging.
• Updated OpenVPN.
• OpenVPN: added configuration import.
• Improved reporting of DSL Statistics.
Bug Fixes
• Resolved an issue with VRRP invalid packet causing restart.
• Resolved issue where VRRP interface was lost on firmware upgrade from Version V1.6.x.x.
• Resolved issue with constant SNMP walk causing restart.
• Resolved issue with L2TP not starting correctly due to DNS lookup failure.
• Removed IPsec 0.0.0.0 messages from logs.
• Resolved issue whereby when an active IPsec tunnel was deleted it was not correctly
removed from the status page.
• Resolved issue with ADSL only configuration setting not persistent.
Note(s)
• None
Version 1.7.6.18 (Build-date: 2019-02-19)
General
• This release includes enhancements and bug fixes.
New Feature(s)
• None.
Enhancement(s)
• Converted Operating mode setting to a DSL Mode setting.
• Improved selection of DSL interface firmware based on connection type.
• Legacy ADSL mode now disabled by default.
Bug Fixes
• Resolved an issue with infrequent configuration read error on boot.
• Resolved an issue with restarting after power glitches.
• Resolved issue preventing IPSec tunnels from being enabled/disabled via the web VPN page.
• Resolved a bug which restarted the DSL line even when there were no physical parameter
changes.
• Resolved issue of limiting the establishment time out to be 15 seconds.
• Fixed "Poll on connection establishment, period" value in connection management not being
saved.
• Clean up valid interfaces lists.
3(10)
Copyright © 2014 Westermo Teleindustri AB
Note(s)
• None
Version 1.7.6.17 (Build-date: 2018-12-07)
General
• Westermo strongly advices all customers to upgrade to this version.
• This release includes bug fixes.
New Feature(s)
• None.
Enhancement(s)
• None.
Bug Fixes
• Fixed issue with OpenVPN static address not persisting through boot.
Note(s)
• None
Version 1.7.6.16 (Build-date: 2018-10-03)
General
• Westermo advices all customers to upgrade to this version.
• This release includes enhancements and bug-fixes.
New Feature(s)
• None.
Enhancement(s)
• Improved connection management.
• Added Sync Speed indicators.
• Security enhancements.
Bug Fixes
• Correctly terminate OpenVPN when disabled.
• Correctly display NAT ranges for target address and netmask in Custom NAT
Version 1.6.6.1 (Build-date: 2017-06-23)
General
• Westermo advices all customers to upgrade to this version.
• This release includes bug-fixes.
New Feature(s)
• None.
Enhancement(s)
• None.
4(10)
Copyright © 2014 Westermo Teleindustri AB
Bug Fixes
• Fixed ADSL packet connection issue.
Version 1.6.6.0 (Build-date: 2017-05-12)
General
• Westermo advices all customers to upgrade to this version.
• This release includes new features and enhancements.
• Highlighted changes to: VRRP.
New Feature(s)
• VRRP interface hold-off time setting added. This feature allows a time to be set prior to the
interface being declared up for VRRP.
• IPsec connection initialisation triggered on becoming VRRP master.
Enhancement(s)
• Improved start up performance.
• Improved stability with multiple VPN terminations.
Bug Fixes
• No bug fixes
Version 1.6.4.0 (Build-date: 2016-05-05)
General
• Westermo strongly advices all customers to upgrade to this version.
• This release includes new features, enhancements and bug fixes.
• Highlighted changes to: WeConnect, SNMP, IPsec, Web, Routing, DNP3
New Feature(s)
• WeConnect – talk to your local Westermo sales representative for more information
o Official support for WeConnect auto-provisioning process.
o WeConnect can be found in the MRD at VPN → WeConnect.
• Technical support feature added to System → Support page
o Note that passwords and logs will be saved upon creating the support-file.
• TLS-encrypted email servers, e.g. Gmail™, can now be used.
o Note that the trust is automatic and validation of the certificate of the
server is done at this stage.
• Accept via the LAN interface any packet that custom NAT accepts.
Enhancement(s)
• SNMP
o Updated the SNMP software-package.
o Added ability to reset the SNMP Engine ID, creating a unique ID for a unit.
o SysName can now be set in SNMP.
• IPsec
o Connection management for IPsec tunnels added.
▪ Sometimes DPD can have interoperability issues between vendors. The
connection management is a work-around for those, and other, use-cases.
o Traffic maps now supports up to 10 different maps / tunnel.
5(10)
Copyright © 2014 Westermo Teleindustri AB
o Fixed IPSec issue when certificates are used.
• Routing (RIP / GRE)
o Enable RIP over GRE tunnels
o RIP to advertise static routes and GRE interfaces.
o Allow point-to-point Multicast over GRE tunnels.
• SSL VPN / OpenVPN
o Added static IP address configuration to SSL VPN (OpenVPN)
• DHCP
o Added the ability to clear DHCP-leases
• CLI
o Upgrade command added
▪ Supports firmware upload (app) and configuration file upload (config)
▪ See “help upgrade” for more information
• Dynamic DNS / DynDNS
o Updated the Dynamic DNS software-package.
• ADSL
o Capture some lost DSL interface state change notifications.
o Improved DSL connection management.
• Misc
o Improved system entropy.
o Web-server no longer responds to SSLv2 or SSLv3 requests.
Bug Fixes
• ADSL configuration
o ADSL configuration to accept unusual characters.
• Web pages
o Fixed issue where Custom NAT web page could very occasionally
cache incorrect information.
o Fixed IE8 compatibility issue with VPN → SSL VPN web page.
o Fixed issue where browser add-on could prevent expansion
of SSL VPN configuration section.
o Fixed IE8 compatibility issue with the Management → SNMP page.
o Fixed an issue where setting the password to/with certain characters
in certain positions would cause the web-authentication to fail.
o Fixed issue where long hostnames were being truncated.
o Fixed issue in the Serial server web-page phone book when deleting
the final “connection” from a connection entry.
o Fixed error where the 64bit interface counters incorrectly jump by 4 Gig.
o Fixed the Reset button on the Routing Default & Static page
o Other misc. web-page issues.
• Log files
o Clean up of SNMP log messages.
• IPsec
o Fixed issue where a LAN cable was needed in any of the Ethernet ports
for the IPsec VPN to establish a connection.
o Fixed issue where the IPsec daemon would restart even if the interface address did
not change. The daemon now restarts only if the interface address is changed.
o Fixed and issue where the firewall would drop all packets when the local interface was
set to DSL
• SSL VPN
o Fixed issued that could occur after uploading an Astaro VPN file.
• GRE
6(10)
Copyright © 2014 Westermo Teleindustri AB
o Fixed issue with policy routing via GRE interfaces.
• SNMP
o The SysDescription OID now returns the correct description.
o Changed the data types of the following SerialServer object Ids from signed to
unsigned:
▪ BytesTX -- 1.3.6.14.1.16177.1.200.5.4.1.1.6.x
▪ BytesRX -- 1.3.6.14.1.16177.1.200.5.4.1.1.7.x
▪ FramingErrors -- 1.3.6.14.1.16177.1.200.5.4.1.1.8.x
▪ OverrunErrors -- 1.3.6.14.1.16177.1.200.5.4.1.1.9.x
▪ ParityErrors -- 1.3.6.14.1.16177.1.200.5.4.1.1.10.x
▪ Breaks -- 1.3.6.14.1.16177.1.200.5.4.1.1.11.x
• VRRP
o Fixed issue preventing the DSL interface updating VRRP on its status.
• Serial Server
o Fixed issue with the Serial Server phone book when deleting the final
"connection" from a connection entry.
• Connection management
o Reset the PING session each time a ping set is started for the connection manager.
▪ Previously the pings could use an old route through the firewall making the
ping possible but any other new traffic would get blocked. In other words the
connection manager would still work for the pings thus defeating the purpose
of the connection manager. This has now been fixed and the pings now work
as the other traffic.
Version 1.6.2.2 (Build-date: 2014-12-12)
• General
• Westermo strongly advices all customers to upgrade to this version.
• This release includes enhancements.
• Highlighted changes to: Modem Emulation
• Note: A component change in new units, serial number > 1185*, requires firmware
version 1.6.2.2. These units (>1185*) cannot be downgraded to previous versions. The
firmware-upgrade code handles this automatically so there is no risk of downgrading
the “wrong” unit.
* Serial number 575 also has the new component and is affected by the above.
• Enhancement(s)
• Modem emulation
o Fixed -- No timeout when “dialing”.
• Bug Fixes
• None.
• Known issue(s)
• None
7(10)
Copyright © 2014 Westermo Teleindustri AB
Version 1.6.2.0 (Build-date: 2014-09-16)
• General
• Westermo strongly advices all customers to upgrade to this version.
• This release includes enhancements.
• Highlighted changes to: Modem Emulation
• Enhancement(s)
• Modem emulation
o Huntgroup support – multiple endpoints per phone book entry
o Extend the number of phone book entries supported
o Allow the phone book to be uploaded and downloaded in a CSV file format
o Rename “Signal on answer” to Custom modem emulation protocol (CM EP)
o AT+CGREG (GPRS network registration status) including roaming.
o AT+CPIN now correctly emulated.
• Bug Fixes
• None.
• Known issue(s)
• Modem emulation
o No timeout when “dialing”.
Version 1.6.1.2 (Build-date: 2013-12-19)
• General
• NOTE THAT A DEVICE CANNOT BE DOWNGRADED TO ANY PREVIOUS
VERSION AFTER AN UPGRADE TO 1.6.1.2 DUE TO HARDWARE LIMITS.
• Westermo strongly advices all customers to upgrade to this version.
• This release includes new features, enhancements and bug-fixes.
• Highlighted changes to: Hardware controller, User management, SCEP, VRRP, IPsec, SNMP,
DNS, SSL VPN, reboot, web-interface.
• New Feature(s)
• Simple Certificate Enrollment Protocol (SCEP)
o Eases management of certificates.
• PPTP
o Allow PPTP to connect to Windows servers.
• Enhancement(s)
• Hardware controller firmware update
• User management
o Guest user can now be explicitly disabled.
• Certificates
o Added the ability to require the remote certificate to be of nsCertType Server.
• IPsec
o The maximum number of IPsec tunnels has been increased to 25.
8(10)
Copyright © 2014 Westermo Teleindustri AB
o Added support for DH Group 768 and DES.
▪ Added for backwards compatibility reasons.
▪ Neither of these options is recommended for use in production environments
due to serious security issues. Use at least DH Group 1024 and AES instead
if possible.
o Added the ability to configure redundant tunnels. Tunnel groups may be created
containing up to two tunnels within each group with automatic fail-over/fallback.
o Added an option to allow the routing information to be added to the routing table only
once the tunnel has been established.
• Support for latest version of Astaro configuration import.
• Various security enhancements
• Change year format in configuration filename to use 4 digits.
• Bug Fixes
o Packet counters
▪ Fixed received and transmit packet counter roll-over.
o DHCP
▪ Various minor issues fixed.
o Web Interface
▪ Fixed various IE8 rendering errors.
▪ Removed additional characters on some pages.
▪ Fixed spelling errors.
▪ LAN port is no longer shown as fault when cable is not connected.
o DNP3
▪ Fixed issue whereby the DNP3 Tx and Rx packet counters were not updating
correctly.
o PPTP
▪ Fixed issue with Windows server not connecting.
▪ Prevent the repated re-starting of PPTP service.
o DNS
▪ Fixed issue with DNS not resolving correctly when a VPN tunnel re-establishes.
o IPsec
▪ Resolved issue when loading CA certificates.
▪ Allow the local traffic map to specify all traffic.
▪ Display the total time the tunnel has been up as well as the time since the last
re-key.
▪ Removed the ability to configure the default route to be Any IPSec tunnel. The
correct way to configure this is to use IPSec traffic maps.
▪ Delay tunnel inialisation to ensure correcting starting order.
▪ Ensure tunnel is only initalised once.
o Serial port
▪ Fixed failure of PPP server and client to start.
o SSL VPN
▪ Fixed issue where an Astaro file input containing an unknown element would
cause the application to terminate.
▪ Fixed issue where an Astaro file was parsed and configuration applied when
the certificate handler was full. New behaviour is when uploading an Astaro
file a warning will be issued if the certificate handler is full and the file will not
be parsed.
o VRRP
▪ Status now shown correctly.
o Power down
9(10)
Copyright © 2014 Westermo Teleindustri AB
▪ Fixed issue where power down would fail to occur.
o Reboot
▪ Fixed issue where the unit would fail to start up following a re-boot command.
• Known issue(s)
• None.
Version 1.6.0.1 (2013-09-06)
• Initial ADSL-350 firmware release.
10(10)
Copyright © 2014 Westermo Teleindustri AB
Contact Westermo technical support
If you have technical questions about this product that are not answered in this document,
you are welcome to contact Westermo.
International
www.westermo.com
support@westermo.se
Phone: +46 16 42 80 00
Fax: +46 16 42 80 01
France
www.westermo.fr
support@westermo.fr
Phone: +33 1 69 10 21 00
Fax: +33 1 69 10 21 01
Germany
www.westermo.de
support@westermo.de
Phone: +49 7254 9540 00
Fax: +49 7254 9540 09
Sweden
www.westermo.se
support.sverige@westermo.se
Phone: +46 21 548 08 00
Fax: +46 21 35 18 50
United Kingdom
www.westermo.co.uk
technical@westermo.co.uk
Phone: +44 1489 580 585
Fax: +44 1489 580 586
Singapore
www.westermo.com.sg
sales@westermo.com.sg
Phone: +65 6743 9801
Fax: +65 6745 0670
Taiwan
www.westermo.com
Phone: +886 2 8911 1710
China
www.cn.westermo.com
sales.cn@westermo.com
Phone: +86 21 6145 0400
North America
www.westermo.com
Phone: +1 847 619 60 68
Fax: +1 847 619 66 74
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
