2. Computers & electronics
  3. Networking
  4. WLAN access points
  5. DT Research
  6. DT382GL

DT Research DT382GL, DT382GS Basic Operation Guide

  • Hello! I am an AI chatbot trained to assist you with the DT Research DT382GL Basic Operation Guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Rugged Tablet
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131
Copyright © 2020, DT Research, Inc. All Rights Reserved.
BOG072820 DT382GL/ DT382GS ENG
INTRODUCTION
The DT Research DT382GL/ DT382GS Rugged Tablet features the integraon of a high
brightness 8” capacive touch screen and a high performance yet energy ecient
processor within a slim, lightweight, durable package. With built-in Wi-Fi, Bluetooth
and a smart card reader as well as opons for back camera, barcode scanner, GNSS,
NFC, and UHF RFID reader, this robust tablet oers seamless informaon capture and
transmission for improved workow. Rated IP65 and MIL-STD-810G, the DT382GL/
DT382GS Handheld Rugged Tablet provides reliable operaon in harsh, mission-
crical environments.
PACKAGE CONTENTS
• One DT382GL/ DT382GS
• One Baery Pack and Handstrap
• AC-DC Power Adapter
• Basic Operaon Guide
* The actual package contents may vary depending on the conguraon acquired.
DT382GL/ DT382GS
Data Capture Modules
Smart Card Reader
Barcode Scanner (oponal)
Back Camera (oponal)
2
Input/ Output Ports
USB Type-C Port (power input)
Audio Jack
USB Port
A
D
C
F
B
E
The DT382GL/ DT382GS
BUTTON ACTION
Power Buon
Windows Key Button
Programmable Buttons
Brightness Control Buttons
RFID Reader Trigger Button/
Programmable Button
Barcode Scanner Trigger Buon/
Programmable Buon
1
4
2
5
3
6
Button Functions
5
6
2
3
B
A
C
D
E
F
1
4
Baery/ Power LED
PRECAUTIONS
•
A
lways exercise care when operang and handling the DT382GL/ DT382GS
•
D
o not disassemble any poron of the DT382GL/ DT382GS, as this will void any
product warranty.
•
D
o not use any power adapter or charging cradle other than the one provided
with the tablet or acquired from the manufacturer or its partners.
•
I
n the unlikely event that abnormal noise, strange odor, or smoke is present,
immediately power down the DT382GL/ DT382GS and disconnect all power
sources. Please report the problem to your device provider immediately.
3
OPERATION
Powering ON and OFF
To acvate DT382GL/ DT382GS, push and quickly release the Power Buon. The display
will come on in a few seconds. To put the DT382GL/ DT382GS in standby mode, push
and quickly release the Power Buon. To turn the DT382GL/ DT382GS o for extended
storage, power o safely using any soware funcon that “shuts down computer”
provided in the soware operang system.
NOTE:
The baery packs shipped with your tablet may be low in power - please use the
AC-DC adapter with the DT382GL/ DT382GS when seng up for the rst me to
fully charge the baery pack.
NOTE:
To conserve power, push and quick release the Power Buon to make the tablet
in standby mode while not in use. Pushing briey on the same bu on will wake
up the system.
NOTE:
When the baery pack is charging, the blue-colored Baery LED should blink
slowly. If plugging in the AC-DC adapter does not trigger this blinking acvity
and the LED stays dark, the baery pack(s) may have been drained substanally.
Unplug/ replug the AC-DC adapter to the DT382GL/ DT382GS a few mes to
acvate the charging process.
NOTE:
Avoid using the Power Buon (“hold 4+ seconds” feature) to turn o the
tablet—this form of hardware shutdown is intended to be a means of recovery
from lockups, and not as normal operaon.
3
5
UHF RFID Reader:
The oponal UHF RFID reader supports EPC Gen2V2 and ISO 18000-63 standard. To
develop an applicaon to use the UHF RFID reader, contact your device provider for a
UHF RFID reader API package
Data Capture Module Operation Guide
If your DT382GL/ DT382GS comes with an RFID Reader refer to the steps below to
congure the sengs.
For More Support
Users can download the Tablet Modules Basic Operaon Guides from the DT Research
website.
NOTE:
To ensure the system performance, turn on only the symbologies you are going to use.
4
Start Up
If the power up (from Standby mode or otherwise) is successful, the appropriate
interface will be displayed aer a launch sequence of several seconds. The wireless
LAN connecon may take 10-15 seconds to be established.
Wireless Networking
Wireless LAN
The DT382GL/ DT382GS is oen delivered with an embedded (user-inaccessible)
802.11ac LAN adapter equipped with a hidden custom antenna.
• Through the support of typical WLAN adapters, the DT382GL/ DT382GS should be
able to detect all 802.11 access points in the vicinity for you to select the access
point of your choice for connecon.
• The SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT362G and the
access points have to match. The SSID is case-sensive and it is recommended
that you enable WEP/WPA/WPA2 encrypon (or advanced alternaves) for
secure access.
• When WEP/WPA/WPA2 is enabled, you may need to consult your network
administrator or your networking equipment literature to properly congure
associated sengs such as Authencaon mode, etc.
• Refer to the access point operang manuals for seng up the 802.11 access
points.
Bluetooth
The Bluetooth conguraon applicaon is enabled from the System Tray or from the
Windows Mobility Center. Follow the instrucons and opons provided within the
applicaon to congure and invoke Bluetooth connecvity with the corresponding
peripherals.
7
Federal Communication Commission Interference
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protecon against harmful interference in
a residenal installaon. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instrucons, may cause harmful interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular
installaon. If this equipment does cause harmful interference to radio or
television recepon, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one of the
following measures:
•
R
eorient or relocate the receiving antenna.
•
I
ncrease the separaon between the equipment and receiver.
•
C
onnect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
•
C
onsult the dealer or an experienced radio/TV technician for help.
FCC Cauon: Any changes or modicaons not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules.
Operaon is subject to the following two condions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operaon.
This device and its antenna(s) must not be co-located or operang in
conjuncon with any other antenna or transmier.
This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du
Canada.
6
/