Aspen Manufacturing CS36D34-145T-000 Installation guide

Brand: Aspen Manufacturing

Model: CS36D34-145T-000

Type: Installation guide

This manual is also suitable for

CS24C34-145T-000

# 123153

INSTALLATION GUIDE

CS & CT SERIES - DEDICATED HORIZONTAL COIL

1. Safety Instruction

2. Inspection

3. Installation Preparation

4. Condensate Drain Preparation

WARNING

Potential safety hazards are alerted using the following symbols. The symbol is used in conjunction with terms

that indicate the intensity of the hazard.

This symbol indicates a potentially hazardous situation, which if not avoided,

could result in serious injury, property damage, product damage or death.

Certied technicians or those individuals

meeting the requirements specied by

NATE may use this information. Property

and product damage or personal injury hazard may occur

without such background.

This symbol indicates a potentially hazardous situation, which if not avoided,

may result in moderate injury or property damage.

Drain lines from the auxiliary drain pan

should NOT be connected to the primary

drain line of the coil.

If the drain pan is constructed of nylon

or plastic; use Teon tape to connect the

drain lines to the threads in the drain pan.

DO NOT USE SOLVENT BASED PIPE DOPE. THIS WILL RE-

DUCE THE LIFE OF THE PAN.

CAUTION

WARNING

All power sources should be discon-

nected prior to servicing. Failure to do

so may cause personal injury or property

damage.

WARNING

Product designed and manufactured to

permit installation in accordance with lo-

cal and national building codes. It is the

installer’s responsibility to ensure that product is installed

in strict compliance with national and local codes. Man-

ufacturer takes no responsibility for damage (personal,

product or property) caused due to installations violating

regulations.

WARNING

ü On receiving the product, visually inspect it for any major shipping

related damages. Shipping damages are the carrier’s responsibility.

Inspect the product labels to verify the model number and options

are in accordance with your order. Manufacturer will not accept dam-

age claims for incorrectly shipped product.

ü Read all the instructions in this guideline carefully while paying

special attention to the WARNING and CAUTION alerts. If any of

the instructions are unclear, clarify with a certied technician before

proceeding. Gather all tools needed for successful installation of the

unit prior to beginning the installation.

ü CS and CT coils are designed with a built in Primary drain pan

only. Please Check local building codes for auxiliary drain pan re-

quirements. The auxiliary drain pan must have a separate drain line

that is properly sloped and terminated in an area visible to the home

owner. The auxiliary pans provide extra protection to the area under

ü Install coil with a mininum 1/4” slope towards the drain connection.

Condensate drain lines must be installed in accordance with local

building codes.

ü The drain lines must be installed with ¼” per foot pitch to provide

free drainage. A condensate trap MUST be installed on the primary

drain line to ensure proper drainage of the condensate. The trap

must be installed in the drain line below the bottom of the drain pan.

Fig. 4-1 illustrates the typical drain trap installation.

the unit should the primary and secondary drain plug up and over-

ow. As expressed in our product warranty; ASPEN WILL NOT BE

BILLED FOR ANY STRUCTURAL DAMAGES CAUSE BY FAIL-

URE TO FOLLOW THIS INSTALLATION REQUIREMENT. The

drains from the auxiliary drain pan must be installed according to the

local building codes.

Fig 4-1. Typical drain line trap set up

# 123153

5A. Horizontal Only Installation

ü The drain pans have a primary (white) and auxiliary (red) drain

connections. If the auxiliary line is required, it should be run spec-

trally from the primary drain line and terminated in a highly visible lo-

cation. Condensate disposal through auxiliary line indicates that the

primary line is plugged and needs cleaning. If a secondary drain line

will not be provided plug the secondary drain. Drain plugs are NOT

to be reused without plumbers tape. Drain line connection should

be nger tightened, then turned no more than one complete turn as

needed to ensure a rm connection. DO NOT overtighten connection

or damage may occur.

5. Coil Installation

ü Clean coil ns with degreasing agent or mild detergent and rinse

ns clean prior to installation.

ü The refrigerant line sizes should be selected according to the rec-

ommendations of the outdoor unit manufacturer.

ü Care must be taken to ensure all connection joints are burr-free

and clean. Failure to do so may increase chances of a leak. It is

recommended to use a pipe cutter to remove the spun closed end of

the suction line.

ü To reduce air leakage, rubber grommets may be present where the

lines pass through the coil case. To avoid damage, remove grom-

mets prior to brazing by sliding over the lines. Use a quenching cloth

or allow the lines to cool before reinstalling the grommets.

ü Use of wet rags/quenching cloth is highly recommended to prevent

weld-related damages to the casing and Schrader valve (if present).

Coil should be installed on the discharge

side of the furnace

CAUTION

Some Aspen coils may include a Schrader

valve on the suction manifold. Ensure that

the Schrader valve and valve core (where

present) are protected from heat to prevent leakage.

CAUTION

The coil is manufactured with dry nitro-

gen pre-charge. Release the pressure

through the Schrader valve test port pri-

or to installation. If holding pressure is not present, return

coil to distributor for exchange.

WARNING

Refer to Furnace/Air Handler manufacturer literature for specic coil

installation guidelines and recommendations.

Duct work must be installed in accordance

with the local building codes. Aspen Mfg is

will not be liable for damages caused due

by nonconformance to local building codes.

CAUTION

Fig 5B-1. Horizontal Left Application

Fig 5B-2. Horizontal Right Application

A dual drain pan (pan within a pan) is used for condensate collec-

tion. Condensate drain ports are located on both left and right sides

of the unit.

Primary

Auxiliary

Note: The primary drain is the higher of the two ports on the

CS. The primary drain is lower one on the CT (CT does not

have a internal secondary drain pan)

A condensate trap, as shown MUST be installed on the primary drain

line to ensure proper drainage of the condensate. Drain lines should

maintain a 1/4” per foot drop for proper condensate drain ow.

Airow Direction

Airow enters through the inlet of the coil and exits at the outlet,

entering the interior of the enclosure for routing to the attached

ductwork.

5B. Horizontal Orientation

# 123153

Note: Photos are for basic illustration purposes only. Actual equip-

ment conguration may differ from that shown.

7. Metering Devices/Liquid Line Conection

Aspen coils are available with two kinds of metering devices a) ow-

rator or b) TXV. The following instructions are separated into sec-

tions by metering device.

Use Piston sizes recommended by the

outdoor unit manufacturer whenever pos-

sible. The piston should be sized accord-

ing to the capacity of the outdoor unit.

CAUTION

Fig 7A-1. Flowrator assembly components

Failure to install the proper piston can

lead to poor system performance and

possible compressor damage.

WARNING

I. Installation

I-1. Disassemble owrator

body using two wrenches and

unscrewing with a counterclock-

wise motion.

7A. Flowrator Coils

1. Ensure suction line connection joints are burr-free and clean.

Failure to do so may increase chances of a leak and introduce con-

taminants to the system. It is recommended to use a pipe cutter to

remove the spun closed end of the suction line.

Do not attempt to touch brazed joints

while hot. Severe burns may result.

WARNING

6. Suction Line Connection

2. Swedge (or use a eld supplied coupler) and braze the eld sup-

plied refrigerant suction line tubing to the coil stub using approved

industry practices.

Some Aspen coils may include a Schrader

valve on the suction manifold. Ensure that

the Schrader valve and valve core (where

present) are protected from heat to prevent leakage.

CAUTION

The sensing bulb and TXV body MUST be

protected from overheating during braz-

ing. The sensing bulb and TXV body must

be covered using a quench cloth or wet cloth when brazing.

Pointing the brazing ame away from the valve and sensing

bulb provide partial protection only.

WARNING

Be aware of the Teon O-ring. Be sure to

replace the O-ring to attain a proper

seal. (The Teon O-ring is located between

the two halves of the owrator)

CAUTION

I-2. Replace the Teon O-ring

(located between the halves).

Discard Schrader if present.

O-ring

I-4. Braze the stub-out portion to the liquid line and let cool.

I-3. Slide the attachment nut onto

the liquid line stub out.

I-6. Tighten the nut to a torque of approximately 10-30 ft-lbs. Do NOT

overtighten the nut. Overtightening will impede the piston movement

during operation.

I-5. Taking care that the white

Teon seal is still in place inside

the owrater body, rmly seat the

stub and screw the attachment

nut to owrater body.

# 123153

During some installations, a piston change may

be required. If so, the installer MUST change the

piston. Use piston sizes recommended by the

outdoor unit manufacturer. If a sizing chart is not

available, use the piston size chart provided be-

low to size the required piston. The size of the

piston is stamped on the piston body (Fig 7A-2).

II. Piston Replacement

Fig 7A-2

Use the chart below when matching coil with an outdoor unit with a

different nominal capacity than the coil.

Note: Photos are for basic illustration purposes only. Actual equip-

ment conguration may differ from that shown.

II-4. Slide the 13/16” nut over

the lineset and separate the two

halves of the owrator.

Be aware of the Teon O-ring. Be sure to

replace the O-ring to attain a proper

seal. (The Teon O-ring is located between

the two halves of the owrator)

CAUTION

Pay close attention to the piston orienta-

tion. The pointed end of the piston MUST

go into the distributor body, towards the

coil. Failure to ensure this orientation will cause the piston

to be bypassed during operation which might damage the

outdoor unit.

CAUTION

II-8. Tighten the nut to a torque of approximately 10-30 ft-lbs. Do NOT

overtighten the nut. Overtightening will impede the piston movement

during operation.

II-9. If present, slide the rubber grommet back to position to prevent

air leakage.

II-6. Replace the piston with one

of the correct size. Do not force

the new piston into the body.

Make sure the piston moves

freely in body.

II-1. Evacuate the system as per manufacturer guidelines and rec-

ommendations

II-2. Turn the 13/16” nut once to release any residual pressure in the

coil.

II-3. After ensuring that the coil

is free of any residual pressure,

disassemble the owrator body

completely using two wrenches.

Take great care not to distort the

feeder tubes. The wrench used

to clasp the nut should be turned

in counter-clockwise direction to

unscrew the nut.

II-5. Pull the piston out using a

small wire or pick. Verify the pis-

ton size (size is typically stamped

on the body of the piston - Fig

7A-2). If a different piston size

is required by the outdoor unit

manufacturer, replace the piston

using the small wire provided with

the piston kit.

II-7. Assemble the two halves correctly and ensure that the Teon

O-ring is present between the two halves (See I-5). Slide the 13/16”

nut onto the distributor body.

7B. TXV Coils

Ensure that the TXV selected is compat-

ible with the refrigerant used in the out-

door system (R22 or R410A). TXV caps are

painted green for R22 or pink for R410A. In absence of col-

or, the caps will be marked with the compatible refrigerant.

CAUTION

The sensing bulb and TXV body MUST be

protected from overheating during braz-

ing. The sensing bulb and TXV body must

be covered using a quench cloth or wet cloth when brazing.

Pointing the brazing ame away from the valve and sensing

bulb provide partial protection only.

WARNING

Fig 7B-1. Components of a typical TXV assembly

# 123153

The valves should be sized according to

the capacity of the outdoor unit. Failure to

install the right valve can lead to poor per-

formance and possible compressor damage.

CAUTION

Ensure that the TXV bulb is in direct con-

tact with the suction/vapor line. Gap be-

tween the bulb and tube should be avoid-

ed. Failure to do so will impair the proper functioning of the

TXV valve.

CAUTION

If the TXV sensing bulb is mounted verti-

cally; the capillary MUST be directed up-

wards. The bulb must be mounted on the

wall opposite to that being directly hit by the refrigerant and

oil leaving the distributor tubes.

CAUTION

I. TXV Bulb Horizontal Mounting

II. TXV Bulb Vertical Mounting

The orientation and location of the TXV bulb has a major inuence

on the system performance.

Fig 7B-3. Recommended location

for vertical TXV bulb mount

As recommended in Section

7B-I, the TXV sensing bulb

should be mounted in a hori-

zontal plane in relation to the

suction/vapor line. However,

some installation congura-

tions may require that the

sensing bulb be mounted ver-

tically. In this instance, place

the bulb opposite the piping

wall being hit by refrigerant

and oil leaving the distributor

tubes, and with capillary tubes

directed upwards as shown in

Fig. 7B-3.

III-1. Inspect the TXV box to conrm that the valve is compatible

with the refrigerant in the system.

Male

(Inlet)

Female

(Outlet)

III-2. Remove the valve from

the box and note the loca-

tion of the inlet side (threaded

male port) and the outlet side

(female swivel nut port).

Note: Photos are for basic illustration purposes only. Actual equip-

ment conguration may differ from that shown.

III. Field-Installed TXV Retrot

When installing an expansion valve, it is not necessary to slide the

coil out of the housing.

For disassembly and piston removal refer to section 7A-I.

III-5. Braze the stub-out portion to the liquid line and let cool.

III-4. Slide the attachment nut onto the liquid line stub out.

(See 7A, I-3)

It is recommended that the TXV bulb be installed parallel to the

ground (on a horizontal plane). The bulb position should be at

2 o’clock or 10 o’clock. Fig. 7B-2 shows the recommended position

for the TXV bulb installation in the horizontal plane.

The TXV sensing bulb SHOULD be mounted on the suction line ap-

proximately 6” from the TXV or coil housing using the metal clamp

provided. In order to obtain a good temperature reading and correct

superheat control, the TXV sensing bulb must conform to ALL of the

following criteria:

1. The sensing bulb MUST be in direct and continuous

contact with the suction line.

2. The sensing bulb should be mounted horizontally on

the suction line.

3. The sensing bulb MUST be mounted at the 2 o’clock or

10 o’clock position on the circumference of the suction line.

4. The sensing bulb MUST be insulated from outside air.

A properly mounted sensing bulb will prevent false readings caused

by liquid refrigerant that may have formed inside the suction/vapor

line. Insulation will protect the sensing bulb from false readings due

to contact with warm air.

Fig 7B-2. Recommended location for horizontal TXV bulb mount

Bulb position at

2 o’clock or

10 o’clock

# 123153

1. Following outdoor unit manufacturer instructions and recommen-

dations, charge the system with dry nitrogen to a maximum pressure

of 150 PSIG.

3. If any leaks or are discovered, relieve system pressure and repair

leaks. Repeat steps 1-3.

4. With no leaks or weak connections present, evacuate the system

and charge as per the outdoor unit manufacturer instructions and

specications.

Do not attempt to touch brazed joints

while hot. Severe burns may result.

WARNING

O-ring

III-6. Remove the additional Tef-

lon O-ring seal from the box and

place on the shoulder just inside

the TXV inlet port. Screw the nut

attached to the stub-out portion of

the owrator body onto the inlet

port of the TXV.

A. Remove the valve stem from

the Schrader port mounted on the

suction line.

B. Screw are nut on TXV equal-

ization tube on to the Schrader

valve stem.

III-7. Tighten all connections taking care to use proper back up.

III-9a. Some Aspen coils come with a Schrader valve on the suction

line. If a Schrader port is present:

III-9b. In some cases, a suction line Schrader port may not be pres-

ent. If a Schrader port is NOT present:

Using a non-bleed expansion valve may re-

quire the use of a hard-start kit. Follow the

outdoor unit manufacturer’s guidelines.

CAUTION

When handling or manipulating the equal-

izer tube, take great care not to kink or

make extreme bends in the tubing.

CAUTION

III-8. Remove the valve identication sticker from the valve and

place it adjacent to the Aspen model number on unit name plate.

9. Leak Check

2. Check all brazed and screw-

on line connections by applying a

soap solution to the joint. A leak

will produce bubbles in the soap

solution.

A. Install a eld-supplied braze-on Schrader

valve like that shown on the suction line near the

intended sensing bulb mounting location. Follow

valve manufacturer instructions and recommen-

dations for installation.

B. Attach equalizer tube to valve as described in

section III-9a above.

III-10. Mount the sensing bulb as described in section 7B-I or 7B-II.

8. Connecting Refrigerant Lines

1. Release nitrogen holding charge by depressing the Shrader Valve

at the liquid line connection. If no gas releases from the coil, contact

distributor regarding potential leak.

2. Cut off Shrader Valve tting at

the liquid line connection. Use a

tubing cutter for this step. Clean

the burr from the cut tubing to

reduce the chance of future

leaks. Connect the liquid line to

the tubing at the indoor unit.

3. Use a tubing cutter to remove

the spun end from the suction

line connection at the air han-

dler. Clean the burr from the cut

tubing to reduce the chance of

future leaks.

4. To avoid heat damage to grommets where present, remove these

prior to brazing by sliding them over the refrigerant lines and out of

the way.

5. Check to determine if the

evaporator coil has a Shrader

tting on the suction manifold.

If yes, remove the valve core

to prevent heat damage during

brazing. Replace the valve core

once the piping has cooled.

6. Flow nitrogen through the piping when brazing.

7. Braze both refrigerant line connections using proper brazing pro-

cedures.

8. When all line connections are brazed, perform a proper system

evacuation procedure per the outdoor unit manufacturer instructions.

9. Seal the penetration openings where the lineset piping enters the

cabinet.

# 123153

An improperly charged system will likely

cause loss in system performance and

may damage the compressor.

CAUTION

Refer to outdoor unit manufacturer charg-

ing guidelines and recommendations. The

recommendations given below are general

in nature and are NOT to supersede outdoor unit manufac-

turer specications.

CAUTION

10. System Charging

1. Remove shipping brackets on both ends of coil cabinet. Bracket

shown below.

2. Slide coil up to furnace (note:

bottom ange on coil cabinet will

slide under furnace, anges on

furnace should slide inside coil

cabinet) Coil cabinet should be

ush to back side of furnace.

For applications where the coil cabinet is the same height as the fur-

nace use the supplied Z bracket to attach to furnace as shown below.

For applications where the coil cabinet is taller than the furnace use

an L shaped ller bracket to attach to furnace to coil, as shown be-

low.( Bracket is supplied with CB coils with the 8th option code selec-

tion -034)

Note: Make sure to seal all connection joints. Method of sealing

should be performed according to local codes.

11. Mounting Dedicated Horizontal Coil to Furnace

Front Side View

Top View of Cabinet

2A. Flowrator coils: Add refrigerant until the superheat measured at

the outdoor unit suction/vapor line matches the superheat from the

chart below.

2B. TXV coils: Add refrigerant until the subcooling measured at the

outdoor unit liquid line matches the subcooling recommendation of

the outdoor manufacturer. If chart is unavailable charge the unit to a

subcooling value of 8ºF +/- 1ºF.

Outdoor

Temp

Superheat

°F D.B. Min Nom Max

65 30 35 40

70 26 30 34

75 21 25 29

80 17 20 23

85 12 15 18

90 8 10 12

4 5 7

100

# 123153

373 Atascocita Rd.

Humble, TX 77396

Phone: 281.441.6500

Toll Free: 800.423.9007

Fax: 281.441.6510

www.aspenmfg.com

# 123153

Revised 10/30/2017. Subject to change without notice and without incurring obligation.

Aspen Manufacturing CS36D34-145T-000 Installation guide

Brand: Aspen Manufacturing

Model: CS36D34-145T-000

Type: Installation guide

This manual is also suitable for

CS24C34-145T-000

Download PDF

report

Aspen Manufacturing CS36D34-145T-000 Installation guide

This manual is also suitable for

Aspen Manufacturing CS36D34-145T-000 Installation guide

Related papers

Other documents