Ferm CTM1001 User manual

Page is loading ...

Ferm 31

EXPLODED VIEW

FCT-300 Combi tool

The following pictograms are used in these instructions for

use:

Denotes risk of personal injury, loss of life or da-

mage to the tool in case of non-observance of

the instructions in this manual.

Denotes risk of electric shock.

Carefully read this manual before using the machine. Ma-

ke sure that you know how the machine functions and how

to operate it. Maintain the machine in accordance with the

instructions to make sure it functions properly. Keep this

manual and the enclosed documentation with the machi-

ne.

SAFETY INSTRUCTIONS

When using electric machines always observe the

safety regulations applicable in your country to redu-

ce the risk of fire, electric shock and personal injury.

Read the following safety instructions and also the

enclosed safety instructions.

Keep these instructions in a safe place!

• Always keep the cord away from the moving parts of

the machine.

• In the case of locking, switch the machine off immedia-

tely and remove the plug from the mains.

• Compare the maximum number of revolutions allo-

wed of the accessories with the number of revolutions

of the machine.

•When you put the machine away the engine must be

switched off and moving parts must have reached a

standstill.

• Never attach an assembly spanner to your machine

with a piece of string or anything similar.

• Never use the axle locking button if the machine is ope-

rating.

• Make sure that the spring chuck diameter is the same

as the axle diameter of the accessory.

• Use a clamping device for securing the work piece.

• Keep your hands away from the work piece.

TECHNICAL SPECIFICATIONS

Voltage 230 V~

Frequency 50 Hz

Power input 135 W

No load speed/min 15000 – 35000

Capacity of spring chuck 3,2 mm

Weight 0,61 kg

L

pa

(sound pressure) 82,4 dB(A)

L

wa

(sound power) 95,4 dB(A)

Vibration value m/s

2

3,239

Electrical safety

Always check that the power supply corresponds to the

voltage on the rating plate.

Your machine is double insulated in accordance

with EN 50144; therefore no earthwire is requi-

red.

Replacing cables or plugs

Immediately throw away old cables or plugs when they ha-

ve been replaced by new ones. It is dangerous to insert the

plug of a loose cable in the wall outlet.

Using extension cables

Only use an approved extension cable suitable for the po-

wer input of the machine. The minimum conductor size is

1.5 mm

2

. When using a cable reel always unwind the reel

completely.

PACKAGE CONTENTS

The package contains:

1 Combitool

1 spring chuck spanner

40 accessories

1 case

1 instructions for use

1 safety section

1 guarantee card

Check the machine, loose parts and accessories for trans-

port damage.

UK

English

2 Ferm

SPARE PARTS LIST FCT-300

REF.NR. DESCRIPTION FERM NR.

406680 SWITCH 1

406681 GRAPHITE BRUSH -

406682 LINE PRINT 2

406683 COLLET CHUCK 3,2 MM 3

406684 COLLET CHUCK 2,4 MM 3

406709 RING 4

406686 BLOCKING KNOB 5

30 Ferm

ASSEMBLY OF ACCESSORIES

Fig. A.

Before assembly always remove the plug from

the mains.

Press down the axle locking button (2) and hold it down.

Using the spring chuck spanner you can undo the spring

chuck (1). Put the accessory in its place. Hold down the ax-

le locking button when you fasten the spring chuck with the

spring chuck spanner.

Never operate the axle locking button if the engi-

ne is still rotating.

OPERATION

Switch on the machine by engaging the on/out switch (A)

By adjusting the adjusting wheel (B) you can regulate the

speed of the Combi tool.

Too high a load at a low speed of the Combi tool

can burn out the engine.

Do not put the machine down when the motor is still run-

ning. Do not place the machine on a dusty surface. Dust

particles may enter the mechanism.

Accessories for the Ferm Combitool

Ferm does not deliver spare accessories for the Combi-

tool. The Combitool is designed to use the standard ac-

cessories of Dremel, Black & Decker, Bosch or Proxxon.

Always check that the maximum rpm of the accessory is

suitable for the maximum speed of the Combitool.

Grinding stones:

When using a grinding stone the first time, use the dres-

sing stone to balance it. The dressing stone can also be

used for cleaning the surface or to give the grinding stone a

special shape.

Material Speed setting

Stone, shell 1

Steel 5

Aluminium, brass 2

Plastic 1

Felt wheels and tip:

The felt wheels or tip should be screwed on the mandrel.

Material Speed setting

Steel 5

Aluminium, brass 3

Plastic 5

Sanding bands and disc:

Material Speed setting

Wood 6

Steel 1

Aluminium, brass 3

Plastic 1

Ferm 3

Stainless steel brushes and bristle brush:

Material Speed setting

Stone, shell 2

Aluminium, brass 2

High speed cutter, Diamond wheel point and Drill:

Material Speed setting

Stone, shell Max

Steel 3

Aluminium, brass 6

Plastic 1

Abrassive disc:

Material Speed setting

Steel 5

Aluminium, brass 3

Plastic 5

MAINTENANCE

Make sure that the machine is not live when car-

rying out maintenance work on the motor.

The Ferm machines have been designed to operate over

a long period of time with a minimum of maintenance. Con-

tinuous satisfactory operation depends upon proper ma-

chine care and regular cleaning.

Cleaning

Regularly clean the machine housing with a soft cloth, pre-

ferably after each use. Keep the ventilation slots free from

dust and dirt.

If the dirt does not come off use a soft cloth moistened with

soapy water. Never use solvents such as petrol, alcohol,

ammonia water, etc. These solvents may damage the

plastic parts.

Lubrication

The machine requires no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part, please con-

tact your local Ferm dealer.

In the back of this manual you find an exploded view

showing the parts that can be ordered.

ENVIRONMENT

In order to prevent the machine from damage during trans-

port, it is delivered in a sturdy packaging. Most of the pack-

aging materials can be recycled. Take these materials to

the appropriate recycling locations.

Take your unwanted machines to your local Ferm-dealer.

Here they will be disposed of in an environmentally safe

way.

GUARANTEE

The guarantee conditions can be found on the separately

enclosed guarantee card.

4 Ferm

VEDLIGEHOLDELSE

Sørg for at maskinen ikke står under strøm, når

der udføres vedligeholdelsesarbejder på meka-

nikken.

Maskinerne fra Ferm er udviklet til at fungere lœnge uden

problemer med et minimum af vedligeholdelse. Ved at

rengøre maskinen regelmœssigt og behandle den kor-

rekt, bidrager De til en lœngere levetid for maskinen.

Rengøring

Rengør regelmœssigt maskinkappen med en blød klud,

helst efter hvert brug. Sørg for at ventilationshullerne er fri

for støv og snavs. Brug en blød klud, der er vœdet i sœbe-

vand til at fjerne hårdnakket snavs. Brug ingen opløs-

ningsmidler, så som benzin, alkohol, ammoniak, osv. Den

slags stoffer beskadiger kunststofdelene.

Smøring

Maskinen behøver ingen ekstra smøring.

Fejl

Kontakt Deres Ferm-forhandler, hvis der opstår fejl som

følge af slitage af en del.

Bagerst i denne brugsanvisning finder De en reservedel-

stegning med de reservedele, der kan bestilles.

MILJØ

For at undgå transportbeskadigelse leveres maskinen i

en solid emballage. Emballagen er så vidt muligt lavet af

genbrugsmateriale. Genbrug derfor emballagen.

Når de udskifter Deres maskinen bør De tage den gamle

maskine med til Deres lokale Ferm-forhandler. Der vil

maskinen blive bearbejdet på miljøvenlig vis.

GARANTI

Lœs det separat vedlagte garantikort for garantibetingel-

serne.

ClEl

■

KONFORMITETSERKLÆRING

(

DK

)

Vi erklærer at under almindeligt ansvar, at dette

produkt er i overenstemmelse med følgende

normer eller normative dokumenter

EN5014401-1:1995, prEN50144-2-3:1994,

EN55014-1:1993 + A1:1997,

EN61000-3-2:1995 + A13:1997,

EN61000-3-3:1995, EN55014-2:1997

i henhold til bestemmelserne i direktiverne:

89/392EEC

73/23EEC

89/336EEC

01-01-2002

GENEMUIDEN NL

W. Kamphof

Quality department

Ferm 29

Page is loading ...

Ferm CTM1001 User manual

Ferm CTM1001 User manual

in other languages

Related papers

Other documents