ZKTeco L4000 Installation guide

Installation Instruction

Version: 1.0

Dat

e: Dec.,2014

L5000

B

A

C

D

E

H

F

G

I

J

C

K

D

L

M

N

O

P

Q

Diagram

Before Installation

1

A

I

J

M

B

F

C

K

E

G

D

50mm

L

N

Q

30mm

40mm

Mounting Hardware Package

35-50mm door thickness

20mm

8mm

PackingList

Mounting Hardware Package

50-65mm door thickness

D

70mm

L

N

45mm

55mm

H

70mm

2

1. Check door thickness, prepare the mounting hardware package and

cylinder.

Door Preparation

Door Thickness

(mm)

D Spindle Length

(mm)

N Screw Length

(mm)

L Screw Length

(mm)

Q Screw Length

(mm)

E Cylinder Length

(mm)

35-50 50 40 30 8 40

50-65 70 55 45 8 50

65-80 70 70 60 8 60

Note 1: The standard lock includes 2 mounting hardware package only, which is used for the door thickness

of 35-50mm and 50-65 mm separately.

Note 2: 40mm cylinder is recommended for the door thickness of 35-50mm. But, it can be used in the door

thickness of 50 -65 mm if the mortise is not placed along the centerline of door side.

3

I

F

2. Check door open direction.

Note 1: Mortise (F) has 2 types: one is for left open, the other is for right open. Please use the correct one.

Note 2: Strike plate (I) has 2 types: one is for inward open, the other is for outward open. Please use the

correct one.

Left inward Right inward

Left outward Right outward

Tips

1. How to change the handle direction?

Press down the component pointed by the arrow.

At the same time, rotate the handle at 180°.

Then release your hand from the pressed component.

4

Pressdown

thecomponent

180°

2. How to use mechanical key ?

A

3. How to use emergency

power?

Cautions

1. New lock is defined as always open mode.

2. Please register administrator firstly to prevent from any illegal access.

3. The lock is equipped with mechanical keys for manual unlocking. Remove mechanical keys from the

package and keep them in a safe place.

4. To power on the lock, four alkaline AA batteries (not included) are required. Non-alkaline and

rechargeable batteries ARE NOT RECOMMENDED.

5. Do not remove batteries when the lock is in working state.

6. The operation of setting lock has a stand-by time limit of 10 seconds. Without any activity, lock will shut

off after 15 seconds.

7. Keep your fingers clean when using this lock.

Remove the cover on the key

hole with screwdriver or nails.

Insert the key into key hole

and rotate 90°.

5

G

F

c

e

n

t

e

r l

ine o

f t

h

e

h

a

ndle

de

s

ire

d

h

and

le

he

ig

ht

Installation

door thick

ness

35~80mm

55

mm

2. Install the mortise(F).

1. Drill holes on the door.

Note 1: Align the template along the vertical

center line of the mortise (F) at the desired

handle height, and tape it to door.

Note 2: Mark the holes first, then start drilling.

B

ac

k

se

t

6

3. Install lock cylinder(E).

H

E

H

Note: Install lock cylinder in right direction,

then tighten screw (H) to fix it.

4. Install spindle(D).

D

Note: Ensure the red dot have to be vertically

upward.

D

7

5. Install outdoor unit(B) with gasket(C).

B

C

8

L

B

C

K

C

L

6. Install mounting plate (K) with

gasket (C) on the door.

7. Install spindle (D) on the door.

D

9

N

8. Install indoor unit (M).

Q

9. Install the battery (O).

N

Q

O

P

Note: Push cable into the hole .

M

10

10.Mark and drill holes for striking.

3mm

69mm

38mm

180mm

130mm

15mm

(Depth)

25mm

(Depth)

27.5mm

16.5mm

21mm

25mm

I

J

G

11.Test the lock by mechanical key(A) or registered fingerprint.

11

A

ZKTeco L4000 Installation guide

ZKTeco L4000 Installation guide

Related papers

Other documents