allen EA0045RC User manual

Category
Fireplaces
Type
User manual
- 0 -
EA0045RC
ELECTRIC FIREPLACE
SAVE THIS MANUAL
You will need this manual for safety instructions, operation procedures, and warranty. Put it and the
original invoice in a safe, dry place for future reference.
Table of Contents
PAGE
IMPORTANT SATETY INSTRUCTIONS 2
DIMENSIONS 3
TECHNICAL SPECIFICATIONS 3
WIRING DIAGRAM 3
ELECTRIC STOVE INSTALLATION 4
OPERATING INSTRUCTIONS 4
MAINTENANCE 5
TROUBLE SHOOTING 6
WARRANTY 6
- 1 -
IMPORTANT SAFETY INSTRUCTIONS:
When using electrical appliances, basic precautions should always be followed to reduce the risk of
fire, electric shock and injury to persons including the following:
1. Read all instructions before using this appliance.
2. This appliance is hot when in use. To avoid burns, don’t let bare skin touch hot surfaces. The grill at the
bottom of this heater in particular will become hot when the heater is active. Keep combustible materials
such as furniture, pillows, bedding, papers, clothes and curtains etc. At least 3 feet(
0.9m)away from the front
of the appliance. Keep all items away from the sides and back of the appliance and take special care not to
block the air intake or exhaust vents. Use handles when moving this heater.
3. Extreme caution is necessary when the appliance is used by or near children or invalids and whenever the
heater is left operating and unattended.
4. Do not operate the appliance if the power cord or plug has been damaged or the heater has been damaged
or malfunctioned in any way. Take the appliance to authorized service facility for examination, electrical or
mechanical adjustment or repair.
5. Do not use outdoors.
6. Do not use the appliance in bathrooms, laundry areas and similar indoor locations, Never locate the
appliance where it may fall into a bathtub or other water container.
7. Do not run the power cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings.
Do not route cord under furniture or appliances. Take care to position the cord away from high traffic areas
and such that it can not be tripped over.
8. To disconnect the appliance, turn all controls “OFF”, then remove the plug from the outlet.
9. This appliance has a polarized plug(one blade is wider than the other). This plug will fit in a fully in a outlet
only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does fit, contact a qualified
electrician to install the proper outlet. Do not change the plug in any way
10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an
electric shock or fire, or damage the appliance.
11. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces like
a bed, where openings may become blocked.
12. A heater has hot and arcing or sparking parts inside. Do not use in areas where gasoline, paint or flammable
liquids are used or stored.
13. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may
cause fire, electric shock or injury to persons.
14. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable
power tap.
15. Do not attempt burn wood or other materials in this heater
16. When transporting or storing the heater, take care to keep both the unit and power cord/plug dry, free from
excessive vibration and away from heat sources.
17. This appliance comes equipped with an overheat protection safety device. Should the appliance begin to
overheat for any reason, it will automatically turn all heater functions of the appliance off. The appliance will
have to be reset prior to continuing use. To reset the overheat protection safety device, turn all controls, plug
the appliance back and turn on
SAVE THESE INSTRUCTIONS FOR FUTURE USE
---------------------------------------------------------------------------------------
Warning: Any use of this appliance other than recommended by the manufacturer in these users
manual ma
y
cause fire, burns, electric shock and /or other serious in
j
uries
- 2 -
DIMENSIONS:
TECHNICAL SPECIFICATIONS
Model# EA0045RC
Rate Voltage AC 120V, 60Hz
Rate Power(Total) 1400W
Power of Heating Apparatus 650W/1300W
Flame Power 80W
Motor Power 20W
Specification of the Bulb 2 pcs E12
- 3 -
ELECTRIC STOVE INSTALLATION
Plugging in the heater
NOTE:
1. This heater is for use on 120 Volts.
2. A 15AMP circuit is required to operate this appliance. If the breaker trips when the appliance is running, you
may need to move the appliance to another location or unplug other appliances that are on the same circuit
3. ADAPTERS ARE NOT ALLOWED CANADA
NOTE: A 15AMP,120 Volts circuit is required. Dedicated circuit is preferred but not essential in all cases, a
dedicated circuit will be required if, after installation, the circuit breaker trips or the fuse blows on a regular basis
when the heater is operating. Additional appliance on the same circuit may exceed the current rating of the circuit
break.
WARNING:
1. Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the
power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire, electric shock or injury
to persons.
2. Construction and electrical outlet wiring must comply with local building codes and other applicable
regulations to reduce the risk of fire, electric shock and injury to persons.
3. Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to
persons, always use a licensed electrician.
BEFORE USING THIS APPLIANCE:
1. Please check the circuit break for this appliance on?
2. Light bulbs may become loose during shipping, if the flame effect is dim or does not operate properly at first,
ensure that the light bulbs are properly secured in the sockets(bulbs should be finger tight, don’t over tighter)
see “Replacing Light Bulb” section of this manual for instructions.
3. The information regarding this appliance can be found on the rating plate located on the back of the unit
PLUGGING IN THE HEATER:
1. Make sure the appliance main “I/O” is switch OFF(refer to operating instruction section)
2. Plug the unit into a no less 15Amp/120V outlet.
- 4 -
OPERATING INSTRUCTIONS
NOTE:
1. When you first turn the heater on, it may emit a slight but harmless odor. This odor results from certain oils or
greases being heated as the appliance is used for the first time. This odor is perfectly safe and will stop shortly,
it will not reoccur after the first operation of the appliance.
Control Panel
Using the Control Panel:
Master Power Switch(A)
Open the cover and push button A down (1) to “on” position.(see FIG A)
FLAME EFFECT
Push “O/I” (On/Off) button (B) or “O/I” (On/Off) button (M) on the remote control to begin flame effect. The red
power light “ ” and dimmer light “ ” will automatically come on. The flame effect can be adjusted by pressing
the dimmer “ ” button (C) or dimmer “ ” button (L) on the remote control. When pressed, the red light will
blink and the flame effect will cycle from high to low. Press the dimmer “ “ button (C) or dimmer “ “ button (L)
on the remote control again to lock in desired flame brightness. The red light “ “ will remain on. This brightness
will be kept until the dimmer “ ” button (C) or dimmer ” button (L) on the remote control is pressed again.
HEAT SETTING
1. Turning on Master Power Switch (A) and “O/I” (On/Off) button (B) or “O/I” button (M) on the remote control
2. Press “650W” button (D) or “650W” button (K) on the remote control to active the low heater setting. The
red light above will indicate that the heater is functioning on low.
3. Press “650W” button (D) or “650W” button (K) on the remote control again to shut off the heater.
4. Press “1300W” button (E) or “1300W” button (J) on the remote control to active the high heater setting.
The red lights above “650W” and “1300W” buttons will indicate that the heater is functioning on high.
5. Press “1300W” button (E) or “1300W” button (J) on the remote control again to shut off the heater.
Note
When the heater begins to work, it will give off cool air for about 10 seconds before the heating function is
activated
- 5 -
Using the Remote Control
This heater includes a remote control. To operate the appliance using the remote control, the Master Power
Switch (A) must be the “ON” position. See below for directions to use the remote control:
Note
Light bulbs may become loose during shipping. If the flame effect is dim or does not operate properly at first,
ensure that the light bulbs are properly secured in the sockets (bulbs should be finger tight, do not over tighten).
See “Replacing Light Bulbs” Section of the manual for instructions.
When you first turn the heater on, it may emit a slight but harmless odor resulting from certain oils or greases
being heated as the appliance is used for the first time. This odor is perfectly safe and will stop shortly. It will not
reoccur after the first operation of this appliance.
This appliance comes equipped with an overheat protection safety device. Should the appliance begin to
overheat for any reason, it will automatically turn all heater functions of the appliance off. The appliance will
have to be reset prior to continuing use. To reset the overheat protection safety device, turn all controls off and
unplug the appliance, wait 10 minutes, plug the appliance back in and turn on.
MAINTENANCE
REPLACING LIGHT BULBS:
1. Ensure that all controls are off, the appliance is unplugged and bulbs are cool to the touch
2. Wear latex gloves to ensure that grease/oil from your hands does not transfer to the bulbs.
3. Remove back panel to access light bulbs.(see Fig B)
4. Remove the burnt out light bulb and replace with a new bulb. Hand tighten the bulbs only-do not over tighten.
5. Replace back panel and screws(see Fig B)
Warning: Before attempting to perform any maintenance on this appliance, turn all controls to the
“OFF” position and unplug. Allow the appliance to be “OFF” For at least 10 minutes before
performing any maintenance in order to allow all components to cool properly.
Warning: Do not exceed the recommended Bulb wattage.
Use only 120V, 40W, B10 chandelier light bulb, Candelabra Base. The lamp holder is model E12
- 6 -
CLEANING
1. To remove dust from glass window, please use clean dry cloth.
2. To remove fingerprints or other marks from glass window, please use clean damp cloth. Do not spray glass
cleaner or other liquids directly onto the window.
3. Clean metal surfaces with a clean damp cloth making sure not to push dust or debris into any air intake or
exhaust vents.
4. Do not use abrasive cleaners or spray liquids on any part of the appliance.
TROUBLE SHOOTING
FREQUENTLY ASKED QUESTIONS(FAQS)
PROBLEM POSSIBLE CAUSE SOLUTION
Flame is dim or not present 1. Light bulbs are burnt out
2. “Flame wand” has come loose
from bracket
1. Inspect light bulbs and replace
if necessary.(see Maintenance
section of this manual)
2. Remove screws holding back
panel in place and remove back
panel. Secure end of “flame
wand” back into the support
bracket.
No warm air is coming from the
heater
1.The overheat protection device
in the appliance has been
triggered
1. Turn all controls off, unplug
the appliance, allow to cool for at
least 10 minutes, plug back in
and restart.
The appliance turns off and will
not turn back on
1.The overheat protection device
in the appliance has been
triggered
2. House circuit breaker has
been tripped.
1. Turn all controls off, unplug
the appliance, allow to cool for at
least 10 minutes, plug back in
and restart.
2. Reset house circuit breaker.
WARRANTY
Thank you for purchasing this product. These products have been made to demanding high quality standards and
are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase.
This warranty does not affect your statutory rights.
Warning: Turn off the appliance, unplug and let cool for at least 10 minutes before attempting to
service. Only a qualified professional should attempt to service or repair the appliance
- 7 -
For service within the warranty period, please contact the store where the product was purchased. Product model
number and proof of purchase are required for any service request. We reserve the right to repair or replace the
defective product, as its discretion
Normal wear and tear, including accessory wear, it not covered under this warranty. The product is guaranteed for
12 months if used for normal trade purpose, and is valid for the original buyer only. Any warranty is deemed invalid if
the product has been overloaded or used improperly, or subject to neglect or attempted repairs other than by an
authorized agent. Heavy-duty,daily professional or hire usage are not guaranteed. We are not responsible for any
costs related to labour, injuries or any other loss incurred during the product installation, repair or replacement,
including any indirect or consequential damages
If you have any problems with how the various functions operate or with internal damage or missing parts please
call 1-866-321-0399 immediately.
NOTE: DO NOT RETURN THIS PRODUCT TO THE STORE BEFORE CALLING THE TOLL FREE NUMBER.
Due to continuous product improvement, we reserve the right to change the product specifications without prior
notice.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

allen EA0045RC User manual

Category
Fireplaces
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI