Intermec EasyCoder PD41 Installation guide

EasyCoder PD41
Intermec
Brand
Intermec
Model
EasyCoder PD41
Type
Installation guide

This manual is also suitable for

Intermec EasyCoder PD41 is a reliable and versatile printer designed to meet your labeling needs. With its advanced features and user-friendly design, it's an ideal choice for various industries and applications. The PD41 offers high-resolution printing, enabling crisp and clear labels. Its fast print speed helps boost productivity, making it suitable for high-volume printing tasks. Additionally, the printer supports various label sizes and types, providing flexibility for your labeling requirements.

Intermec EasyCoder PD41 is a reliable and versatile printer designed to meet your labeling needs. With its advanced features and user-friendly design, it's an ideal choice for various industries and applications. The PD41 offers high-resolution printing, enabling crisp and clear labels. Its fast print speed helps boost productivity, making it suitable for high-volume printing tasks. Additionally, the printer supports various label sizes and types, providing flexibility for your labeling requirements.

EasyCoder
®
PD41/PD42
EasyLAN Ethernet Interface Installation Instructions
These instructions tell you how to install the EasyLAN Ethernet Interface
Board in a EasyCoder PD41/PD42 printer. The kit includes the following:
• EasyLAN Ethernet Interface Board
Required Tools
To install the interface board in your printer, you need these tools:
• Screwdriver, slotted
• Screwdriver, Phillips
Installing the Interface Board
Before you begin installation, please acknowledge the following important
safety notes:
The installation described in this section must only
be performed by an authorized service technician.
Intermec assumes no responsibility for personal
injury or damage to the equipment if the
installation is performed by an unauthorized
person.
Die in diesem Abschnitt beschriebene Installation
darf nur von einem autorisierten
Wartungstechniker durchgeführt werden. Intermec
übernimmt keine Verantwortung für Verletzungen
oder Sachschäden, falls die Installation von einer
unberechtigten Person durchgeführt wird.
Make sure the printer has been turned off and
disconnected from the power supply before you
start installation.
Stellen Sie sicher, dass der Drucker abgeschaltet
und von der Stromversorgung abgetrennt wurde,
bevor Sie mit der Installation beginnen.
To install the EasyLAN Ethernet Interface Board
1 Turn off the printer and unplug the power cord.
2 Open the side door. Remove the two screws that hold the cover to the
electronics compartment.
3 Lay the printer down on its side, with the electronics compartment facing
up.
4 Loosen the electronics compartment cover by placing the tip of a slotted
screwdriver at the edge of the cover and gently pushing the handle
towards the top of the printer. DO NOT attempt to bend it loose.
Take precautions against electrostatic discharge,
for example, by wearing grounded wrist straps.
5 Slide the cover out along the rails and remove it from the printer.
6 Put the printer back in upright position.
7 Locate the screw in the upper left corner of the electronics compartment
that holds the main board in place. Remove the screw.
Worldwide Headquarters
6001 36th Avenue West
Everett, Washington 98203
U.S.A.
tel 425.348.2600
fax 425.355.9551
www.intermec.com
©
2007 Intermec Technologies
Corporation. All rights reserved.
8 Connect the EasyLAN board to the connector marked “Ethernet
Option” on the main board.
9 Reattach the screw.
10 Reattach the cover.
When you turn on the printer, it automatically recognizes the EasyLAN
board.
Please refer to the EasyLAN Software Installation Instructions
(P/N 1-960667-xx) for information on configuring the network settings. If
you have a PD42 printer you can change settings directly from the display,
for help see the EasyCoder PD42 Printer User’s Guide (P/N 934-009-xxx).
EasyCoder PD41/PD42 EasyLAN Ethernet Interface Installation Instructions
*1-960656-01*
P/N 1-960656-01
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Intermec EasyCoder PD41 Installation guide

EasyCoder PD41
Intermec
Brand
Intermec
Model
EasyCoder PD41
Type
Installation guide
This manual is also suitable for

Intermec EasyCoder PD41 is a reliable and versatile printer designed to meet your labeling needs. With its advanced features and user-friendly design, it's an ideal choice for various industries and applications. The PD41 offers high-resolution printing, enabling crisp and clear labels. Its fast print speed helps boost productivity, making it suitable for high-volume printing tasks. Additionally, the printer supports various label sizes and types, providing flexibility for your labeling requirements.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents