H3C S3610 Series Operating instructions

Brand: H3C

Model: S3610 Series

Type: Operating instructions

This manual is also suitable for

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Table of Contents

Table of Contents

Chapter 1 SSH Configuration.......................................................................................................1-1

1.1 SSH2.0 Overview...............................................................................................................1-1

1.1.1 Algorithm and Key...................................................................................................1-1

1.1.2 Asymmetric Key Algorithm......................................................................................1-2

1.1.3 SSH Operating Process..........................................................................................1-2

1.2 Configuring the Device as an SSH Server ........................................................................1-6

1.2.1 SSH Server Configuration Task List .......................................................................1-6

1.2.2 Enabling SSH Server..............................................................................................1-6

1.2.3 Configuring the User Interfaces for SSH Clients.....................................................1-6

1.2.4 Configuring RSA and DSA Keys.............................................................................1-7

1.2.5 Configuring a Client Public Key...............................................................................1-9

1.2.6 Configuring an SSH User......................................................................................1-10

1.2.7 Setting the SSH Management Parameters...........................................................1-12

1.3 Configuring the Device as an SSH Client........................................................................1-13

1.3.1 SSH Client Configuration Task List.......................................................................1-13

1.3.2 Specifying a Source IP address/Interface for the SSH client................................ 1-13

1.3.3 Configuring Whether First-time Authentication is Supported................................1-13

1.3.4 Establishing a Connection Between the SSH Client and the Server....................1-15

1.4 Displaying and Maintaining SSH .....................................................................................1-15

1.5 SSH Server Configuration Examples...............................................................................1-16

1.5.1 When Using Password Authentication..................................................................1-16

1.5.2 When Using Publickey Authentication..................................................................1-18

1.6 SSH Client Configuration Examples................................................................................1-24

1.6.1 When Using Password Authentication..................................................................1-24

1.6.2 When Using Publickey Authentication..................................................................1-27

Chapter 2 SFTP Service................................................................................................................ 2-1

2.1 SFTP Overview..................................................................................................................2-1

2.2 Configuring an SFTP Server..............................................................................................2-1

2.2.1 Configuration Prerequisites.....................................................................................2-1

2.2.2 Enabling the SFTP Server ......................................................................................2-1

2.2.3 Configuring the SFTP Connection Idle Timeout Period..........................................2-2

2.3 Configuring an SFTP Client...............................................................................................2-2

2.3.1 Specifying a Source IP Address or Interface for the SFTP Client ..........................2-2

2.3.2 Establishing a Connection to the SFTP Server.......................................................2-3

2.3.3 Working with the SFTP Directories.........................................................................2-3

2.3.4 Working with SFTP Files.........................................................................................2-4

2.3.5 Displaying Help Information....................................................................................2-5

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Table of Contents

2.3.6 Terminating the Connection to the Remote SFTP Server ......................................2-6

2.4 SFTP Configuration Example............................................................................................2-6

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-1

Chapter 1 SSH Configuration

When configuring SSH, go to these sections for information you are interested in:

z SSH2.0 Overview

z Configuring the Device as an SSH Server

z Configuring the Device as an SSH Client

z Displaying and Maintaining SSH

z SSH Server Configuration Examples

z SSH Client Configuration Examples

1.1 SSH2.0 Overview

Secure Shell (SSH) offers an approach to securely logging into a remote device. By

encryption and strong authentication, it protects devices against attacks such as IP

spoofing and plain text password interception.

The device can not only work as an SSH server to support connections with SSH

clients, but also work as an SSH client to allow users to establish SSH connections with

a remote device acting as the SSH server.

 Note:

Currently, when acting as an SSH server, the device supports two SSH versions: SSH2

and SSH1. When acting as an SSH client, the device supports SSH2 only.

1.1.1 Algorithm and Key

Algorithm is a set of transformation rules for encryption and decryption. Information

without being encrypted is known as plain text, while information that is encrypted is

known as cipher text. Encryption and decryption are performed using a string of

characters called a key, which controls the transformation between plain text and cipher

text, for example, changing the plain text into cipher text or cipher text into plain text.

Figure 1-1 Encryption and decryption

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-2

Key-based algorithm is usually classified into symmetric key algorithm and asymmetric

key algorithm.

1.1.2 Asymmetric Key Algorithm

Asymmetric key algorithm means that a key pair exists at both ends. The key pair

consists of a private key and a public key. The public key is effective for both ends,

while the private key is effective only for the local end.

Asymmetric key algorithm encrypts data using the public key and decrypts the data

using the private key, thus ensuring data security.

You can also use the asymmetric key algorithm for digital signature. For example, user

1 adds his signature to the data using the private key, and then sends the data to user 2.

User 2 verifies the signature using the public key of user 1. If the signature is correct,

this means that the data originates from user 1.

Revest-Shamir-Adleman Algorithm (RSA) and Digital Signature Algorithm (DSA) are

both asymmetric key algorithms. RSA can be used for data encryption and signature,

whereas DSA is used for signatures only.

 Note:

Currently, SSH2 supports both RSA and DSA.

1.1.3 SSH Operating Process

The session establishment between an SSH client and the SSH server involves the

following five stages:

Table 1-1 Stages in establishing a session between the SSH client and the server

Stages Description

Version negotiation

SSH1 and SSH2 are supported. The two parties

negotiate a version to use.

Key and algorithm negotiation

SSH supports multiple algorithms. The two parties

negotiate an algorithm for communication.

Authentication

The SSH server authenticates the client in

response to the client’s authentication request.

Session request This client sends a session request to the server.

Interactive session

The client and the server start to communicate with

each other.

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-3

I. Version negotiation

z The server opens port 22 to listen to connection requests from clients.

z The client sends a TCP connection request to the server. After the TCP

connection is established, the server sends the first packet to the client, which

includes a version identification string in the format of “SSH-<primary protocol

version number>.<secondary protocol version number>-<software version

number>”. The primary and secondary protocol version numbers constitute the

protocol version number, while the software version number is used for

debugging.

z The client receives and resolves the packet. If the protocol version of the server is

lower but supportable, the client uses the protocol version of the server; otherwise,

the client uses its own protocol version.

z The client sends to the server a packet that contains the number of the protocol

version it decides to use. The server compares the version carried in the packet

with that of its own to determine whether it can cooperate with the client.

z If the negotiation is successful, the server and the client proceed with key and

algorithm negotiation; otherwise, the server breaks the TCP connection.

 Note:

All the packets involved in the above steps are transferred in plain text.

II. Key and algorithm negotiation

z The server and the client send key algorithm negotiation packets to each other,

which include the supported public key algorithm list, encryption algorithm list,

MAC algorithm list, and compression algorithm list.

z Based on the received algorithm negotiation packets, the server and the client

figure out the algorithms to be used.

z The server and the client use the DH key exchange algorithm and parameters

such as the host key pair to generate the session key and session ID.

Through the above steps, the server and the client get the same session key, which is

to be used to encrypt and decrypt data exchanged between the server and the client

later. The server and the client use session ID in the authentication stage.

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-4

Caution:

Before the negotiation, the server must have already generated the RSA and DSA key

pairs, which are mainly used for generating the session key.

III. Authentication

z The client sends to the server an authentication request, which includes the

username, authentication method and information related to the authentication

method (the password in the case of password authentication).

z The server authenticates the client. If the authentication fails, the server informs

the client by sending a message, which includes a list of available methods for

re-authentication.

z The client selects a method from the list to initiate another authentication.

z The above process repeats until the authentication succeeds or the authentication

times timeout and the session is torn down.

SSH provides two authentication methods: password authentication and publickey

authentication.

In password authentication:

z The client encrypts the username and password, encapsulates them into a

password authentication request, and sends the request to the server.

z Upon receiving the request, the server decrypts the username and password,

compares them against those it maintains, and then informs the client of the

authentication result.

In publickey authentication:

z The server authenticates clients using digital signatures. Currently, the device

supports two publickey algorithms to implement digital signatures: RSA and DSA.

The client sends to the server a public authentication request containing its user

name, public key and algorithm. The server validates the public key. If the public

key is invalid, the authentication fails; otherwise, the server generates a digital

signature to authenticate the client, and then sends back a message to inform the

success or failure of the authentication.

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-5

 Note:

Besides password authentication and publickey authentication, SSH provides another

two authentication methods:

z password-publickey: Performs both password authentication and publickey

authentication of the client. A client running SSH1 client only needs to pass either

type of the two, while a client running SSH2 client must pass both of them to login.

z any: Performs either password authentication or publickey authentication. The

client tries publickey authentication first.

IV. Session request

After passing authentication, the client sends a session request to the server, while the

server listens to and processes the request from the client. If the client passes

authentication, the server sends back to the client an SSH_SMSG_SUCCESS packet

and goes on to the interactive session stage with the client. Otherwise, the server

sends back to the client an SSH_SMSG_FAILURE packet, indicating that the

processing fails or it cannot resolve the request.

V. Interactive session

In this stage, the server and the client exchanges data in this way:

z The client encrypts and sends the command to be executed to the server.

z The server decrypts and executes the command, and then encrypts and sends the

result to the client.

z The client decrypts and displays the result on the terminal.

 Note:

z During interactive session, the client can send the commands to be performed by

pasting the text, which must be within 2000 bytes. It is recommended that the text

pasted be commands in the same view; otherwise, the server may not be able to

perform the commands.

z If the text exceeds 2000 bytes, you can upload the configuration file to the server

and use the configuration file to restart the server so that the server executes the

commands.

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-6

1.2 Configuring the Device as an SSH Server

1.2.1 SSH Server Configuration Task List

Complete the following tasks to configure an SSH server:

Task Remarks

Enabling SSH Server Required

Configuring the User Interfaces for SSH Clients Required

Creating RSA or DSA key pairs Required

Exporting RSA or DSA key pairs Optional

Configuring

RSA and DSA

Keys

Destroying RSA or DSA key pairs Optional

Configuring a Client Public Key

Required for publickey

authentication users and

optional for password

authentication users

Configuring an SSH User Optional

Setting the SSH Management Parameters Optional

 Note:

As a client uses either RSA or DSA algorithm for authentication and different clients

may support different algorithms, the server needs to generate both RSA and DSA key

pairs for successful authentication.

1.2.2 Enabling SSH Server

Follow these steps to enable SSH server:

To do… Use the command… Remarks

Enter system view

system-view

—

Enable the SSH server

function

ssh server enable

Required

Disabled by default

1.2.3 Configuring the User Interfaces for SSH Clients

An SSH client accesses the device through a VTY user interface. Therefore, you need

to configure the user interfaces for SSH clients to allow SSH login. Note that the

configuration takes effect at the next login.

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-7

Follow these steps to configure the protocols for the current user interface to support:

To do… Use the command… Remarks

Enter system view

system-view

—

Enter user interface view

of one or more user

interfaces

user-interface vty number

[ ending-number ]

Required

Set the login

authentication method to

scheme

authentication-mode

scheme

[ command-authorization ]

Required

By default, the

authentication mode is

password.

Specify the protocols for

the user interfaces to

support

protocol inbound { all | ssh

| telnet }

Optional

All protocols are

supported by default.

Caution:

z For detailed information about the authentication-mode and protocol inbound

commands, refer to Login Commands.

z If you configure a user interface to support SSH, be sure to configure the

corresponding authentication method with the authentication-mode scheme

command.

z For a user interface configured to support SSH, you cannot configure the

authentication-mode password command and the authentication-mode none

command.

1.2.4 Configuring RSA and DSA Keys

I. Creating RSA or DSA key pairs

For successful SSH login, you must create the RSA or DSA key pairs first.

Follow these steps to create an RSA or DSA key pair:

To do… Use the command… Remarks

Enter system view

system-view

—

Create the local RSA key

pair

public-key local create

rsa

Create the local DSA key

pair

public-key local create

dsa

Required

Use either command.

By default, there is neither

RSA key pair nor DSA key

pair.

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-8

Caution:

z Configuration of the rsa local-key-pair create and public-key local create dsa

command can survive a reboot. You only need to configure it once.

z The length of an RSA server/host key is in the range 512 to 2048 bits. With SSH2,

however, some clients require that the keys generated by the server must not be

less than 768 bits.

z The length of a DSA host key is in the range 512 to 2048 bits. With SSH2,

nevertheless, some clients require that the keys generated by the server must not

be less than 768 bits.

II. Exporting RSA or DSA key pairs

You can display or export the local RSA or DSA host key for setting the host key on the

remote end.

Follow these steps to display or export an RSA or DSA host key:

To do… Use the command… Remarks

Enter system view

system-view

—

Display the local RSA host key on

the screen in a specified format, or

export it to a specified file

public-key local export

rsa { openssh | ssh1 |

ssh2 } [ filename ]

Display the local DSA host key on

the screen in a specified format, or

export it to a specified file

public-key local export

dsa { openssh | ssh2 }

[ filename ]

Required

Use either

command.

III. Destroying RSA or DSA key pairs

Follow these steps to destroy an RSA or DSA key pair:

To do… Use the command… Remarks

Enter system view

system-view

—

Destroy the local RSA key

pair

public-key local destroy

rsa

Destroy the local DSA key

pair

public-key local destroy

dsa

Required

Use either command.

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-9

1.2.5 Configuring a Client Public Key

 Note:

This configuration task is only necessary for SSH users using publickey authentication.

For an SSH user that uses publickey authentication to login, the server must be

configured with the client RSA or DSA host public key in advance, and the

corresponding private key for the client must be specified on the client.

You can manually configure or import the publickey public key from a public key file. In

the former case, you can manually copy the client’s public key configuration to the

server. In the latter case, the system automatically converts the public key to a string

coded using the PKCS standard. Before importing the public key, you must upload the

public key file (in binary) to the server through FTP or TFTP.

Caution:

z When the device functions as the SSH server, you cannot use Secure CRT 4.07 to

upload the client public key to the server.

z You can configure at most 20 client pubic keys on an SSH server.

I. Configuring a client public key manually

Follow these steps to configure the client public key manually:

To do… Use the command… Remarks

Enter system view

System-view

—

Enter public key view

public-key peer

keyname

—

Enter public key code

view

public-key-code begin —

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-10

To do… Use the command… Remarks

Configure a client public

key

Enter the content of the

public key

Required

The content must be a

hexadecimal string that is

generated randomly by

the SSH-supported client

software and coded

compliant to PKCS.

Spaces and carriage

returns are allowed

between characters.

Return from public key

code view to public key

view

public-key-code end

—

When you exit public key

code view, the system

automatically saves the

public key.

Return from public key

view to system view

peer-public-key end —

II. Importing a client public key from a public key file

Follow these steps to import a public key from a public key file:

To do… Use the command… Remarks

Enter system view

system-view

—

Import the public key from

a public key file

public-key peer

keyname import sshkey

filename

Required

1.2.6 Configuring an SSH User

This configuration allows you to create an SSH user and specify the service type and

authentication method.

Follow these steps to configure an SSH user:

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-11

To do… Use the command… Remarks

Enter system view

system-view

—

For stelnet

users

ssh user username service-type

stelnet authentication-type

{ password | { any |

password-publickey | publickey }

assign publickey keyname }

Create an

SSH user,

and specify

the service

type and

authenticati

on method

For all

users or

sftp users

ssh user username service-type { all

| sftp } authentication-type

{ password | { any |

password-publickey | publickey }

assign publickey keyname

work-directory directory-name }

Required

Use either

command.

Caution:

z After passing AAA authentication, an AAA user without SSH user account still can

log on to the server using password authentication and Stelnet or SFTP service.

z An SSH server supports up to 1024 SSH users.

z The service type of an SSH user can be Stelnet or SFTP. stelnet, or the secure

Telnet protocol, refers to the traditional SSH service. For information about stelnet,

refer to

SSH2.0 Overview. sftp represents the secure FTP protocol. For information

about sftp, refer to

SFTP Overview.

z For successful login through SFTP, you must set the user service type to sftp or all.

z You can set the service type of an SSH user to stelnet or all if the user does not

need SFTP service.

z As SSH1 does not support service type sftp, if the client uses SSH1 to log in to the

server, you must set the service type to stelnet or all on the server. Otherwise, the

client will fail to log in successfully.

z The working folder of an SFTP user is subject to the user authentication method.

For a user using only password authentication, the working folder is the AAA

authorized one. For a user using only publickey authentication or using both the

publickey and password authentication methods, the working folder is the one set

by using the ssh user command.

z The configured authentication method takes effect when the user logs in next time.

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-12

 Note:

For users using publickey authentication:

z You must configure on the device the corresponding username and public keys.

z After login, the commands available for a user are determined by the user privilege

level, which is configured with the user privilege level command on the user

interface. By default, the command privilege level is 0.

For users using password authentication:

z You can configure the accounting information either on the device or on the remote

authentication server (such as RADIUS authentication server).

z After login, the commands available to a user are determined by AAA authorization.

1.2.7 Setting the SSH Management Parameters

SSH management includes:

z Enabling the SSH server to be compatible with SSH1

z Setting the server key pair update interval, applicable to users using SSH1 client.

z Setting the SSH user authentication timeout period

z Setting the maximum number of SSH authentication attempts

Setting the above parameters can help avoid malicious guess at and cracking of the

keys and usernames, securing your SSH connections.

Follow these steps to set the SSH management parameters:

To do… Use the command… Remarks

Enter system view

system-view

—

Enable the SSH server to

work with SSH1.x clients

ssh server

compatible-ssh1x

enable

Optional

By default, the SSH

server can work with

SSH1.x clients.

Set the RSA server key

pair update interval

ssh server

rekey-interval hours

Optional

0 by default, that is, the

RSA server key pair is not

updated.

Set the SSH user

authentication timeout

period

ssh server

authentication-timeout

time-out-value

Optional

60 seconds by default

Set the maximum number

of SSH authentication

attempts

ssh server

authentication-retries

times

Optional

3 by default

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-13

 Note:

Authentication will fail if the number of authentication attempts (including both

publickey and password authentication) exceeds that specified in the ssh server

authentication-retries command.

1.3 Configuring the Device as an SSH Client

1.3.1 SSH Client Configuration Task List

Complete the following tasks to configure an SSH client:

Task Remarks

Specifying a Source IP address/Interface for the SSH client Optional

Configuring Whether First-time Authentication is Supported Optional

Establishing a Connection Between the SSH Client and the Server Required

1.3.2 Specifying a Source IP address/Interface for the SSH client

This configuration task allows you to specify a source IP address or interface for the

client to access the SSH server, improving service manageability.

To do… Use the command… Remarks

Enter system view

system-view

—

Specify a source IPv4

address or interface for

the SSH client

ssh client source { ip

ip-address | interface

interface-type

interface-number }

Specify a

source IP

address or

interface

for the

SSH client

Specify a source IPv6

address or interface for

the SSH client

ssh client ipv6 source

{ ipv6 ipv6-address |

interface interface-type

interface-number }

Required

By default, the

address of the

interface

decided by the

routing is used

to access the

SSH server

1.3.3 Configuring Whether First-time Authentication is Supported

When the device connects to the SSH server as an SSH client, you can configure

whether the device supports first-time authentication.

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-14

z With first-time authentication, when an SSH client not configured with the server

host public key accesses the server for the first time, the user can continue

accessing the server, and save the host public key on the client for use in

subsequent authentications.

z Without first-time authentication, a client not configured with the server host public

key will be denied of access to the server. To access the server, a user must

configure in advance the server host public key locally and specify the public key

name for authentication.

I. Enable the device to support first-time authentication

Follow these steps to enable the device to support first-time authentication:

To do... Use the command… Remarks

Enter system view

system-view

—

Enable the device to

support first-time

authentication

ssh client first-time enable

Optional

By default, first-time

authentication is

supported on a client.

II. Disable first-time authentication

For successful authentication of an SSH client not supporting first-time authentication,

the server host public key must be configured on the client and the public key name

must be specified.

Follow these steps to disable first-time authentication:

To do... Use the command… Remarks

Enter system view

system-view

—

Disable first-time

authentication support

undo ssh client first-time

Optional

By default, first-time

authentication is

supported on a client.

Configure the server

public key

Refer to 1.2.5 Configuring a

Client Public Key

Required

The method of configuring

server public key on the

client is similar to that of

configuring client public

key on the server.

Specify the host public

key name of the server

ssh client authentication

server server assign

publickey keyname

Required

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-15

1.3.4 Establishing a Connection Between the SSH Client and the Server

Follow these steps to establish the connection between the SSH client and the server:

To do... Use the command… Remarks

Establish a

connection between

the SSH client and

the IPv4 server, and

specify the preferred

key exchange

algorithm,

encryption

algorithms, and

HMAC algorithms for

them

ssh2 server [ port-number ]

[ identity-key { dsa | rsa } |

prefer-ctos-cipher { aes128 |

des } | prefer-ctos-hmac

{ md5 | md5-96 | sha1 |

sha1-96 } | prefer-kex

{ dh-group-exchange |

dh-group1 | dh-group14 } |

prefer-stoc-cipher { aes128 |

des } | prefer-stoc-hmac

{ md5 | md5-96 | sha1 |

sha1-96 } ] *

Establish a

connection

between

the SSH

client and

the server,

and specify

the

preferred

key

exchange

algorithm,

encryption

algorithms,

and HMAC

algorithms

for them

Establish a

connection between

the SSH client and

the IPv6 server, and

specify the preferred

key exchange

algorithm,

encryption

algorithms, and

HMAC algorithms for

them

ssh2 ipv6 server

[ port-number ] [ identity-key

{ dsa | rsa } |

prefer-ctos-cipher { aes128 |

des } | prefer-ctos-hmac

{ md5 | md5-96 | sha1 |

sha1-96 } | prefer-kex

{ dh-group-exchange |

dh-group1 | dh-group14 } |

prefer-stoc-cipher { aes128 |

des } | prefer-stoc-hmac

{ md5 | md5-96 | sha1 |

sha1-96 } ] *

Required

Use either

command

in user

view.

1.4 Displaying and Maintaining SSH

To do… Use the command… Remarks

Display information about the

public keys of the local key pair

display public-key local

{ dsa | rsa } public

Available in any

view

Display information about the

public keys

display public-key peer

[ brief | name

publickey-name ]

Available in any

view

Display the source IP address or

interface currently set for the

SFTP client

display sftp client

source

Available in any

view

Display the source IP address or

interface currently set for the

SSH client

display ssh client

source

Available in any

view

Display the status information or

session information of an SSH

server

display ssh server

{ status | session }

Available in any

view

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-16

To do… Use the command… Remarks

Display the mappings between

host public keys and SSH

servers saved on a client

display ssh server-info

Available in any

view

Display information about a

specified or all SSH users on the

SSH server

display ssh

user-information

[ username ]

Available in any

view

1.5 SSH Server Configuration Examples

1.5.1 When Using Password Authentication

I. Network requirements

z As shown in Figure 1-2, a local SSH connection is established between the host

(SSH client) and the switch (SSH server) for secure data exchange.

z Password authentication is required.

II. Network diagram

SSH client SSH server

Host Switch

192.168.0.2/24

Vlan-int1

192.168.0.1/24

Figure 1-2 Network diagram for SSH server configuration (using password

authentication)

III. Configuration procedure

Configure the SSH server

# Generate RSA and DSA key pairs and enable the SSH server.

<Switch> system-view

[Switch] public-key local create rsa

[Switch] public-key local create dsa

[Switch] ssh server enable

# Configure an IP address for VLAN interface 1. This address will serve as the

destination for the SSH client in connecting the server.

[Switch] interface vlan-interface 1

[Switch-Vlan-interface1] ip address 192.168.1.40 255.255.255.0

[Switch-Vlan-interface1] quit

# Set the authentication mode for the user interface to AAA.

[Switch] user-interface vty 0 4

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-17

[Switch-ui-vty0-4] authentication-mode scheme

# Enable the user interface to support SSH.

[Switch-ui-vty0-4] protocol inbound ssh

[Switch-ui-vty0-4] quit

# Create local user client001, and set the user command privilege level to 3

[Switch] local-user client001

[Switch-luser-client001] password simple aabbcc

[Switch-luser-client001] service-type ssh level 3

[Switch-luser-client001] quit

# Specify the service type for user client001 as Stelnet, and the authentication

method as password.

[Switch] ssh user client001 service-type stelnet authentication-type password

Configure the SSH client

 Note:

There are a variety of SSH client software, such as PuTTY, OpenSSH, and so on. The

following is an example of configuring SSH client using PuTT v0.58.

# Establish a connection with the SSH server

Launch PuTTY.exe to enter the following interface. In the Host Name (or IP address)

text box, enter the IP address of the server (192.168.1.40).

Operation Manual – SSH

H3C S5500-EI Series Ethernet Switches Chapter 1 SSH Configuration

1-18

Figure 1-3 SSH client configuration interface

From the window shown in

Figure 1-3, click Open. The following SSH client interface

appears. If the connection is normal, you will be prompted to enter the username

(client001) and password (aabbcc)

1.5.2 When Using Publickey Authentication

I. Network requirements

z As shown in Figure 1-4, a local SSH connection is established between the host

(SSH client) and the switch (SSH server) for secure data exchange.

z Publickey authentication is used, the algorithm is RSA.

II. Network diagram

SSH client SSH server

Host Switch

192.168.1.56/24

Vlan-int1

192.168.1.40/24

Figure 1-4 Network diagram of SSH server configuration (using publickey

authentication)

Page is loading ...

H3C S3610 Series Operating instructions

Brand: H3C

Model: S3610 Series

Type: Operating instructions

This manual is also suitable for

Download PDF

report

H3C S3610 Series Operating instructions

This manual is also suitable for

H3C S3610 Series Operating instructions

Related papers

Other documents