H3C S3100-52P Operating instructions

Brand: H3C

Model: S3100-52P

Type: Operating instructions

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Table of Contents

Table of Contents

Chapter 1 SSH Terminal Service..................................................................................................1-1

1.1 SSH Terminal Service .......................................................................................................1-1

1.1.1 Introduction to SSH.................................................................................................1-1

1.1.2 SSH Server Configuration.......................................................................................1-3

1.1.3 SSH Client Configuration......................................................................................1-10

1.1.4 Configuring the Device as an SSH Client............................................................. 1-17

1.1.5 Displaying SSH Configuration...............................................................................1-19

1.1.6 SSH Server Configuration Example...................................................................... 1-19

1.1.7 Configuring the Device as an SSH Client Configuration Example........................1-21

1.2 SFTP Service...................................................................................................................1-23

1.2.1 Introduction to SFTP.............................................................................................1-23

1.2.2 SFTP Server Configuration...................................................................................1-23

1.2.3 SFTP Client Configuration on the Switch.............................................................. 1-24

1.2.4 SFTP Configuration Example................................................................................1-28

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-1

Chapter 1 SSH Terminal Service

1.1 SSH Terminal Service

1.1.1 Introduction to SSH

Secure shell (SSH) provides secure communication and powerful authentication for

remote user login to a switch over an insecure network, thus preventing assaults such

as IP address spoofing, plain-text password interception.

Currently, the S3100-52P Ethernet Switches support SSH2.0. Acting as an SSH server,

a switch allows for the connections of multiple SSH clients. Through SSH Client, a user

can establish a connection to a switch or UNIX host running SSH Server.

Figure 1-1 and Figure 1-2 shows two ways to establish SSH connection between client

and server.

z Establishing SSH connection through a LAN

100BASE-TX

Server

Ethernet

Workstation

Laptop

SSH

Switch

SSH

100BASE-TX

Server

Ethernet

Workstation

Laptop

SSH Client

Switch

SSH Server

100BASE-TX

Server

Ethernet

Workstation

Laptop

SSH

Switch

SSH

100BASE-TX

Server

100BASE-TX

Server

Ethernet

Workstation

Laptop

SSH

Switch

SSH

100BASE-TX

Server

Ethernet

Workstation

Laptop

SSH Client

Switch

SSH Server

Figure 1-1 Establish SSH connection through a LAN

z Establishing SSH connection through a WAN

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-2

Local switch

Local Ethernet

WANServer

SSH

Laptop

Workstation

Remote Ethernet

Server

WANServer

SSH

Laptop

WANServer

SSH

Laptop

Workstation

Rem

Remote sw itch

SSH

ote Ethernet

Server

WANServer

SSH

Laptop

Workstation

Remote Ethernet

Server

WANServer

SSH

Laptop

WANServer

SSH

Laptop

Workstation

Rem

SSH

ote Ethernet

Server

Local switch

Local Ethernet

WANServer

SSH

Laptop

Local switch

Local Ethernet

WANServer

SSH

Laptop

Workstation

Remote Ethernet

Server

WAN

Laptop

Workstation

Remote Ethernet

Server

WANServer

SSH

Laptop

WANServer

SSH

Laptop

WANServer

SSH

Laptop

Server

SSH

Laptop

Workstation

Rem

Remote sw itch

SSH

ote Ethernet

Server

WANServer

SSH

Workstation

Rem

Remote sw itch

SSH

ote Ethernet

Server

WANServer

SSH

Laptop

Workstation

Laptop

Workstation

Remote Ethernet

Server

WANServer

SSH

Laptop

Workstation

Remote Ethernet

Server

WANServer

SSH

Laptop

WANServer

SSH

Laptop

WANServer

SSH Client

Laptop

Workstation

Rem

SSH Server

ote Ethernet

Server

Local switch

Local Ethernet

WANServer

SSH

Laptop

Local switch

Local Ethernet

WANServer

SSH

Laptop

Workstation

Remote Ethernet

Server

WAN

Laptop

Workstation

Remote Ethernet

Server

WANServer

SSH

Laptop

WANServer

SSH

Laptop

WANServer

SSH

Laptop

Server

SSH

Laptop

Workstation

Rem

Remote sw itch

SSH

ote Ethernet

Server

WANServer

SSH

Workstation

Rem

Remote sw itch

SSH

ote Ethernet

Server

WANServer

SSH

Laptop

Workstation

Laptop

Workstation

Remote Ethernet

Server

WANServer

SSH

Laptop

Workstation

Remote Ethernet

Server

WANServer

SSH

Laptop

WANServer

SSH

Laptop

WANServer

SSH

Laptop

Workstation

Rem

SSH

ote Ethernet

Server

Local switch

Local Ethernet

WANServer

SSH

Laptop

Local switch

Local Ethernet

WANServer

SSH

Laptop

Workstation

Remote Ethernet

Server

WAN

Laptop

Workstation

Remote Ethernet

Server

WANServer

SSH

Laptop

WANServer

SSH

Laptop

WANServer

SSH

Laptop

Server

SSH

Laptop

Workstation

Rem

Remote sw itch

SSH

ote Ethernet

Server

WANServer

SSH

Workstation

Rem

Remote sw itch

SSH

ote Ethernet

Server

WANServer

SSH

Laptop

Workstation

Laptop

Workstation

Remote Ethernet

Server

WANServer

SSH

Laptop

Workstation

Remote Ethernet

Server

WANServer

SSH

Laptop

WANServer

SSH

Laptop

WANServer

SSH Client

Laptop

Workstation

Rem

SSH Server

ote Ethernet

Server

Figure 1-2 Establish SSH connection through a WAN

The communication process between a SSH client and server goes through the

following five stages.

1) Version negotiation stage:

z The client sends a TCP connection request to the server.

z When a TCP connection is established, the two ends begin to negotiate an SSH

version.

z If they get a successful negotiation, they go to the key negotiation stage.

Otherwise the server terminates the TCP connection.

2) Key negotiation stage:

z The server sends the public key in a randomly generated RSA key pair to the

client.

z The client calculates a session key by using the public key received from the

server and a random number it generates randomly.

z The client encrypts the random number with the public key from the server and

sends the result data to the server.

z The server then decrypts the received data with the private key in the RSA key pair

to get the random number on the client.

z The server calculates a session key by using the public key and the random

number through the same algorithm as the client.

Then, the server and the client get the same session key, and use it for data encryption

and decryption to secure their subsequent communication.

3) Authentication negotiation stage:

z The client sends its username information to the server.

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-3

z The server starts to authenticate the user. If the user is configured as having no

authentication on the server, the following step is skipped and the session request

stage starts directly.

z The server authenticates the user in some way (see the following note), till the

authentication succeeds or the connection is terminated due to authentication

timeout.

 Note:

SSH provides two kinds of authentication: password authentication and RSA

authentication.

(1) Password authentication works as follows:

z The client sends the username and password to the server.

z The server compares the received username and password against those

configured locally. The user passes the authentication if the server finds a match for

both username and password.

(2) RSA authentication works as follows:

z Configure the RSA public key of the client at the server.

z The client sends the member module of its RSA public key to the server.

z The server checks the validity of the member module. If it is valid, the server

generates a random number, which is sent to the client after being encrypted with

RSA public key of the client.

z Both the server and the client calculate authentication data by using the random

number and session ID.

z The client sends the authentication data it calculates to the server.

z The server compares the received authentication data with the authentication data

on itself. If they are identical, the authentication succeeds.

4) Session request stage. The client sends a session request to the server, which

processes the request and establish a session.

5) Interactive session stage. Both ends exchange data till the session ends.

1.1.2 SSH Server Configuration

The following table describes SSH Server configuration tasks.

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-4

Table 1-1 SSH2.0 Server configuration tasks

Operation Command Related section

Configure user interface(s) to

support specified protocol(s)

protocol inbound

Section “

Configuring

user interface(s) to

support specified

protocol(s)

Generate local RSA key pair

rsa local-key-pair create

Destroy local RSA key pair

rsa local-key-pair

destroy

Section “

Generating

or destroying local

RSA key pair

Specify a default

authentication type for SSH

users

ssh authentication-type

default

Configure authentication type

for an SSH user

ssh user username

authentication-type

Section "

Configuring

authentication type for

a user

Set SSH authentication

timeout time

ssh server timeout

Set SSH authentication retry

times

ssh server

authentication-retries

Section “Configuring

SSH management

Configure a client public key

for an SSH user

ssh user username

assign rsa-key keyname

Section “

Configuring a

client public key for a

user

I. Configuring user interface(s) to support specified protocol(s)

Table 1-2 Configure user interface(s) to support specified protocol(s)

Operation Command Description

Enter system view

system-view

—

Enter the view of one or

multiple user interfaces

user-interface

[

type-keyword ] number

[

ending-number ]

Required

Configure the user

interface(s) to support

specified protocol(s)

protocol inbound

{ all

|ssh | telnet }

Optional

By default, both Telnet

and SSH are supported.

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-5

Caution:

z If you have configured a user interface to support SSH protocol, to ensure a

successful login to the user interface, you must configure AAA authentication for the

user interface by using the authentication-mode scheme command.

z For a user interface, if you have executed the authentication-mode password or

authentication-mode none command, the protocol inbound ssh command

cannot be executed; if you have executed the protocol inbound ssh command,

neither of the authentication-mode password and authentication-mode none

commands can be executed.

II. Generating or destroying local RSA key pair

This configuration task is used to generate or destroy an RSA key pair on the server,

which is named in the format of switch name plus "_Host", for example, H3C_host.

After you issue the rsa local-key-pair create command, the system prompts you to

input a key length.

In SSH2.0, the key length is in the range of 512 to 2,048 (bits).

Table 1-3 Generate or destroy local RSA key pair

Operation Command Description

Enter system view

system-view

—

Generate local RSA key pair

rsa local-key-pair create

Required

Destroy local RSA key pair

rsa local-key-pair destroy

Optional

Caution:

z For a successful SSH login, you must first generate the RSA key pair of the server.

z You just need to execute the rsa local-key-pair create command once, and need

not execute the command again after the system is rebooted.

z If you re-execute the rsa local-key-pair create command, the system will ask

whether you want to replace the original key pair with a new one.

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-6

 Note:

After the rsa local-key-pair create command is executed, you can execute the

display rsa local-key-pair public command to display information about the public

key (in H3C_host, for example).

III. Configuring authentication type for a user

For a new user, you must specify the authentication type. Otherwise, the user cannot

access the switch.

Table 1-4 Configure authentication type for a user

Operation Command Description

Enter system view

system-view

—

Specify a default

authentication type for

SSH users

ssh authentication-type

default

{ password | rsa

| password-publickey |

all }

Configure authentication

type for an SSH user

ssh user username

authentication-type

{ password |

password-publickey |

rsa| all }

At least one required;

By default, no

authentication type is

specified for an SSH user,

and the user can not

access the switch.

Note that:

z The ssh authentication-type default command is used to configure the default

authentication type for all SSH users.

z The ssh user username authentication-type command is used to configure an

authentication type for a specific SSH user.

z When both commands are configured with different authentication types, for the

specific user (user specified by the username argument), the authentication type

specified by the ssh user username authentication-type command will take

effect instead of that specified for all SSH users.

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-7

Caution:

z If RSA authentication type is configured for a user, the RSA public key of the client

user must be configured on the switch.

z By default, no authentication type is specified for a new user, and the new user

cannot access the switch.

z For the password-publickey authentication type, users can access the switch only

when they pass both kinds of authentications.

z For the password authentication type, username should be consistent with the

valid user name defined in AAA; for the RSA authentication type, username is the

SSH local user name, so that there is no need to configure a local user in AAA.

z If the default authentication type for SSH users is password and local AAA

authentication is adopted, you need not use the ssh user command to create an

SSH user. Instead, you can use the local-user command to create a user name and

its password and then set the service type of the user to SSH.

z If the default authentication type for SSH users is password and remote

authentication (RADIUS authentication, for example) is adopted, you need not use

the ssh user command to create an SSH user, because it is created on the remote

server. And the user can use its username and password configured on the remote

server to access the network.

IV. Configuring SSH management

The configuration of SSH management includes the setting of authentication timeout

time, and authentication retry times. After the configuration, the SSH management

function is able to prevent illegal activities such as malicious password guessing, thus

ensure the security of SSH connections.

Table 1-5 Configure SSH management

Operation Command Description

Enter system view

system-view

—

Set SSH

authentication

timeout time

ssh server timeout

seconds

Optional

By default, the timeout

time is 60 seconds.

Set SSH

authentication retry

times

ssh server

authentication-retries

times

Optional

By default, the number of

retry times is 3.

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-8

V. Configuring a client public key for a user

On the switch, you can configure a client public key (generated randomly on a client) for

a client user. This configuration is not required for password authentication type.

There are two methods to configure a client public key for a user.

1) Manual configuration

First, perform the following operations on a client:

z Use the SSH2.0 client software to randomly generate a RSA key pair.

z Use the SSHKEY.exe program to transform the public key in the RSA key pair to

PKCS (public-key cryptography standards) format.

Then, perform the following operations on the server:

Table 1-6 Configure client public key for a user

Operation Command Description

Enter system view

system-view

—

Enter public key view

rsa peer-public-key

key-name

Required

Enter public key edit

view to input a client

public key

public-key-code

begin

When you input the key data,

spaces are allowed between the

characters you input (because the

system can remove the spaces

automatically); you can also press

<Enter> to continue your input at

the next line. But the key you input

should be a hexadecimal digit

string coded in the public key

format.

Return to public key

view from public key

edit view

public-key-code

end

The system saves the public key

data you input when exiting public

key edit view.

Return to system

view from public key

view

peer-public-key

end

—

Assign a client public

key to an SSH user

ssh user username

assign rsa-key

keyname

Required

Keyname

is the name of an

existing public key. If the user has

already been assigned with a

public key, the newly assigned

public key overwrites the old one.

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-9

 Note:

The above method requires you to transform the format of the public key on the client,

and then manually configure the transformed public key on the server. So, the method

is relatively more complex.

2) Automatic configuration

First, perform the following operations on a client:

z Use the SSH2.0 client software to randomly generate a RSA key pair.

z Use FTP/TFTP to transfer the corresponding public key file to the Flash memory of

the server.

Then, perform the following operations on the server:

Table 1-7 Automatic configuration

Operation Command Description

Enter system view

system-view

—

Transform the format of the key

in a client public key file and

automatically configure a client

public key on the server

rsa peer-public-key

key-name import

sshkey file-name

filename must be

consistent with the name

of a public key file in the

Flash memory.

 Note:

The above method does not require you to manually configure a public key. So the

method is relatively simple and is the recommended method.

VI. Specifying a source IP address/interface for the SSH server

You can perform the following configurations to specify a source IP address or a source

interface for the SSH server, thus enhancing traffic manageability.

Table 1-8 Specify a source IP address/interface for the SSH server

Operation Command Description

Enter system view

system-view

—

Specify a source IP address

for the SSH server

ssh-server source-ip ip-address

Optional

Specify a source interface

for the SSH server

ssh-server source-interface

interface-type interface-number

Optional

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-10

1.1.3 SSH Client Configuration

A variety of SSH client software are available, such as PuTTY and FreeBSD. For an

SSH client to establish a connection with an SSH server, you must complete these

configuration tasks:

z Specifying the IP address of the server

z Selecting the protocol for remote connection Usually, a client can use a variety of

remote connection protocols, such as Telnet, Rlogin, SSH. To establish an SSH

connection, you must select SSH.

z Selecting the SSH version Since the device supports SSH Server 2.0 now, select

2.0 or lower for the client.

z Specifying the RSA private key file. The RSA keys for an SSH user include a

public key and a private key, which are generated by the tool accompanied with

the client software. The public key must be configured on the server, while the

private key must be configured on the client.

The following takes the client software of PuTTY, PuTTYGen and SSHKEY as

examples to illustrate how to configure the SSH client:

I. Generating the Client Key

To generate the client key pair, run PuTTYGen.exe, choose “SSH2(RSA)” in the

parameter field and click “Generate”.

Figure 1-3 Generating the client key (1)

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-11

While generating the key pair, you must move the mouse continuously. The mouse

should be restricted off the green process bar in the blue box of

Figure 1-4. Otherwise,

the process bar does not move and the key pair cannot be generated.

Figure 1-4 Generating the client key (2)

After the key pair is generated, click “Save public key” and enter the file name (public

for here) to save the key pair.

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-12

Figure 1-5 Generating the client key (3)

Likewise, to save a private key, click “Save private key” and a warning window pops up

to prompt you whether to save a private key without any precautions. Click “Yes” and

enter a name (private for here) to save the private key.

Figure 1-6 Generating the client key (4)

To generate RSA public key in PKCS format, run SSHKEY.exe, click “Browse” and

select the public key file, and then click “Convert”.

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-13

Figure 1-7 Generating the client key (5)

II. Specifying the IP address of the server

Launch PuTTY.exe and the following window appears.

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-14

Figure 1-8 SSH client interface 1

In the [Host Name (or IP address)] text box, enter the IP address of the server, for

example, 10.110.28.10. Note that the IP address can be the IP address of any interface

on the server that has SSH in the state of up and a route to the client.

III. Selecting the protocol for remote connection

As shown in Figure 1-8, select the [SSH] option from the [Protocol] section.

IV. Selecting the SSH version

From the category on the left of the window, click [Connection/SSH]. The window as

shown in

Figure 1-9 appears.

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-15

Figure 1-9 SSH client interface 2

In the [Protocol options] field, select [2] from the [Preferred SSH protocol version]

section.

V. Open an SSH Connection with RSA

If the client needs to use RSA authentication, you must specify the RSA private key file.

If the client needs to use password authentication, this is not required.

From the category on the left of the window, click [Connection/SSH/Auth]. The following

window appears.

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-16

Figure 1-10 SSH client interface 3

Click <Browse…> to bring up the file selection window, navigate to the private key file

and click <OK>.

VI. Open an SSH Connection with Password

1) Click <Open>. The following SSH client interface appears. If the connection is

normal, you will be prompted to enter the username and password, as shown in

Figure 1-11.

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-17

Figure 1-11 SSH client interface

2) Enter the username and password to create an SSH connection.

3) To log out, enter the quit command.

1.1.4 Configuring the Device as an SSH Client

The following table describes SSH Client configuration tasks.

Table 1-9 SSH Client configuration tasks

Operation Command Description

Enter system view

system-view

—

Enable the client to

run initial

authentication

ssh client first-time enable

Optional

By default, the client is

enabled to run initial

authentication.

If the client is disabled

from running initial

authentication, you must

assign a public key to the

server on the client.

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-18

Operation Command Description

Assign a public key

to a server

ssh client server-ip

assign

rsa-key

keyname

Optional

This command is used to

configure the public key of

a server on the client, so

that the client can regard

the server as a reliable

server when it connects to

the server.

Start the client to

establish a

connection with an

SSH server

ssh2

{ host-ip | host-name }

[

port-num ] [ prefer_kex

{

dh_group1 |

dh_exchange_group } ]

[

prefer_ctos_cipher { des |

aes128 } ] [ prefer_stoc_cipher

{ des | aes128 } ]

[

prefer_ctos_hmac { sha1 |

sha1_96 | md5 | md5_96 } ]

[

prefer_stoc_hmac { sha1 |

sha1_96 | md5 | md5_96 } ]

Required

In this command, you can

also specify the preferred

key exchange algorithm,

encryption algorithms and

HMAC algorithms

between the server and

client.

HMAC: Hash-based

message authentication

code

 Note:

If an SSH client is enabled to run initial authentication, when the SSH client accesses

an SSH server for the first time and it does not have the public key of the server, the

client allows you to select to continue the access and save the public key of the server

to local device; when the client accesses the server at the next time, it authenticates the

server against the public key saved locally.

I. Specifying a source IP address/interface for the SSH client

You can perform the following configuration to specify a source IP address or a source

interface for the SSH2.0 client, thus enhancing traffic manageability.

Table 1-10 Specify a source IP address/interface for the SSH client

Operation Command Description

Enter system view

system-view

—

Specify a source IP address

for the SSH2.0 client.

ssh2 source-ip ip-address

Optional

Specify a source interface

for the SSH2.0 client

ssh2 source-interface

interface-type interface-number

Optional

Operation Manual – SSH Terminal Service

H3C S3100-52P Ethernet Switch Chapter 1

SSH Terminal Service

1-19

1.1.5 Displaying SSH Configuration

After the above configuration, you can execute the display command in any view to

display the configuration information and running status of SSH, so as to verify your

configuration.

Table 1-11 Display SSH configuration

Operation Command Description

Display host and server

public keys

display rsa

local-key-pair public

Display client RSA public

key(s)

display rsa

peer-public-key

[ brief |

name keyname ]

Display SSH status and

session information

display ssh server {

status

| session }

Display SSH user

information

display ssh

user-information

[ username ]

Display the current source

IP address or the IP

address of the source

interface specified for the

SSH server.

display ssh-server

source-ip

Display the current source

IP address specified for

the SSH2.0 Client.

display ssh2 source-ip

You can execute the

display command in any

view.

1.1.6 SSH Server Configuration Example

I. Network requirements

As shown in Figure 1-12, The PC (SSH Client) running an SSH2.0-supported client

software, establish a local connection with the switch (SSH Server) to ensure the

security of data exchange.

Page is loading ...

H3C S3100-52P Operating instructions

H3C S3100-52P Operating instructions

H3C S3100-52P Operating instructions

Related papers

Other documents