Marantec USV Owner's manual

Brand: Marantec

Model: USV

Category: Rechargeable batteries

Type: Owner's manual

Marantec USV is an uninterruptible power supply (UPS) battery management system designed to provide backup power to compatible drives and control systems in dry areas. With Marantec USV, you can ensure that your door system, including standard roller and sectional door drives, can be opened and closed even in the event of a power failure. It comes in different product variants to suit your specific power requirements:

USV 750 VA: Ideal for connecting to a 230 V / 1~ power supply.
USV 1000 - 1500 VA: Suitable for use with a 400 V / 3~ power supply.
USV 5000 - 7500 VA: Designed for higher power applications.

USV 750 VA: Ideal for connecting to a 230 V / 1~ power supply.
USV 1000 - 1500 VA: Suitable for use with a 400 V / 3~ power supply.
USV 5000 - 7500 VA: Designed for higher power applications.

Battery management system UPS / Rev. B 0.2 – 1

Product description

Battery management system UPS

2 – Battery management system UPS / Rev. B 0.2 Battery management system UPS / Rev. B 0.2 – 3

2 – Battery management system UPS / Rev. B 0.2

1. Contents

− Copyright.

− No part of these instructions may be reproduced without

our prior approval.

− Subject to alterations in the interest of technical progress.

− All dimensions given in mm.

− The diagrams in this manual are not to scale.

Key to symbols

WARNING!

Indicates a hazard with a medium level of risk which, if not

avoided, could result in death or serious injury.

CAUTION!

Indicates a hazard with a low level of risk which, if not

avoided, could result in minor or moderate injury.

ATTENTION!

Indicates an imminent danger of damage or destruction.

CHECK

Indicates a check to be performed.

REFERENCE

Reference to separate documents which must be complied

with.

☞ Action request

− List, itemisation

➔ Reference to other sections of this document

2. Information in this document

1. Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

2. Information in this document . . . . . . . . . . . . .2

3. Safety information. . . . . . . . . . . . . . . . . . . . . .3

3.1 Warranty ..........................3

3.2 Use for the intended purpose ...........3

3.3 Target group........................3

3.4 Instructions regarding installation and

connection .........................3

3.5 Information concerning operation ........3

3.6 Safety instructions for accumulators ......3

4. Product information. . . . . . . . . . . . . . . . . . . . .4

5. Product variants. . . . . . . . . . . . . . . . . . . . . . . .6

5.1 USV 750 VA ........................6

5.2 USV 1000 - 1500 VA .................7

5.3 USV 5000 - 7500 VA .................8

6. Technical data . . . . . . . . . . . . . . . . . . . . . . . . .9

2 – Battery management system UPS / Rev. B 0.2 Battery management system UPS / Rev. B 0.2 – 3

3. Safety information

WARNING!

Failure to comply with the documentation could

result in life-threatening danger!

☞ Be sure to follow all the safety instructions in this docu-

ment.

3.1 Warranty

The function and safety of the equipment is only guaranteed

if the warning and safety instructions included in these

operating instructions are adhered to.

The manufacturer is not liable for personal injury or damage

to property if these occur as a result of the warnings and

safety advice being disregarded.

The manufacturer does not accept any liability or warranty

for damage due to the use of non-approved spare parts and

accessories.

3.2 Use for the intended purpose

The uninterruptible power supply UPS is designed for

operation with standard roller and sectional door drives and

serves as a self-sufcient energy supply. With this, the door

system can also be opened and closed in the event of a

power failure.

3.3 Target group

Only qualied and trained electricians may connect,

programme and service the control.

Qualied and trained electricians must meet the following

requirements:

− knowledge of the general and specic safety and accident

prevention regulations.

− knowledge of the relevant electrical regulations,

− training in the use and care of appropriate safety

equipment.

− capable of recognising the dangers associated with

electricity.

3.4 Instructions regarding installation and

connection

− The control is designed with X type terminals.

− The system must be disconnected from the electricity supply

before carrying out any electrical work. It must be ensured

that the electricity supply remains disconnected for the

duration of the work.

− Local protective regulations must be complied with.

− Consult the manufacturer before carrying out modications

or replacing the mains connection cable.

3.5 Information concerning operation

− Unauthorised persons (particularly children) should not be

allowed to play with permanently installed adjusting or

control devices.

− Keep remote controls beyond the reach of children.

Observe the valid standards and regulations!

3.6 Safety instructions for accumulators

The UPS systems contain a varying number of accumulators

with different energy levels, depending on the power output.

Although the accumulators are maintenance-free, it is

necessary to consider a number of points with regards to

storage, charging and use.

Service life

The accumulators used in our UPS systems are designed for

a service life of 5 years. However, the service life is decisively

inuenced by

− the ambient temperature

− the type of charge

− the type of use

Ambient temperature

The ambient temperature must lie within a range of +1°C

to +27°C. Upward and downward deviations from this

temperature result in a signicant reduction in the service life.

Charge

The UPS system is delivered charged. However, the

accumulator must be fully charged before using for the rst

time for safety reasons.

Use

The UPS system can and should be connected and switched

on as a general rule, in order that the accumulators are

being constantly charged (trickle charging). During extended

breaks between use (storage without mains connection),

the accumulators must be repeatedly recharged on a regular

basis.

− With UPS systems with 100 - 4000 VA output every

3months

− With UPS systems with 5000 - 7500 VA output every

2months

4 – Battery management system UPS / Rev. B 0.2

4. Product information

4.1 Information about the product

The UPS battery management systems are to be exclusively

used for the control of compatible drives and control systems

in dry areas.

The UPS battery management systems may only be used to

power equipment that do not exceed the manufacturer’s

given maximum values.

The installer and the user must ensure that all applicable legal

and ofcial requirements regarding the use of the products, in

particular the current EMC guideline concerning installation

and operation, are observed.

4.2 Installation

Information:

− The mains cable must not be exchanged with the output

cable.

− The neutral conductor (N) and the outer conductor (L)

on the input side must not be connected to the neutral

conductor (N) and the outer conductor (L) on the output

side.

− For three-phase current, a clockwise rotating eld is

required.

− The cable for the door control must always be 3-wire or

5-wire at 1x230 or 3x400V.

Connection:

☞ Plug the supply line (A) into the socket of the on-site power

supply.

☞ Plug the control system’s supply line into the appropriate

socket (B)

☞ Switch the battery management system to the ON position

with the key switch (C)

☞ Fix the casing with plugs and screws in the desired position.

The mounting holes are located in the back wall of the

cabinet.

Meaning of signals and buttons:

BAT / POWER = battery OK

ON = battery management system is switched on

UPS = battery operation mode (power failure)

ON = switch on

OFF = switch off

Fault message

If the accumulators of the UPS system are defective, the

yellow diagnostic LED (100-4000 VA) or blue diagnostic LED

(5000-7500 VA) goes out and an acoustic warning signal

sounds. If the output voltage of the accumulators lies below

a dened value, this is also detected as a fault and is only

signalled with an acoustic warning. The emergency operation

may not function faultlessly in this case. Operation of the

UPS system with an accumulator that has been reported as

defective is not permissible. The UPS system must be replaced

immediately in this case.

Maintenance

During maintenance of the complete door system, it is

necessary to test the function of the UPS. Defective UPS

systems must be replaced immediately. UPS systems that have

exceeded their service life must also be replaced immediately.

In order to guarantee faultless operation on a continuous

basis, it is essential that the UPS system be replaced after

5 years in operation. In the event of any violation of these

maintenance instructions, it is not possible to guarantee the

functional safety of the system and therefore also the safety

of buildings and persons.

Safety information

Battery management system UPS / Rev. B 0.2 – 5

REFERENCE

All technical data can be found in the separate data sheets.

4.3 UPS circuit diagram

4.3 / 1

C C

N N

PE PE

A USV input

B USV output

C L or L1-3

D Input

E Output

F UPS logic module

6 – Battery management system UPS / Rev. B 0.2 Battery management system UPS / Rev. B 0.2 – 7

5.1 USV 750 VA

5.1 / 1

GHI

CAUTION!

As soon as the battery management system is connected

to a power supply, it will also feed power. This also applies

when the battery management system is switched off!

☞ Please connect the battery management system to a 230 V /

1~ power supply.

☞ Switch the battery management system on. The two LEDs

“BAT” = orange and “ON” = green should now light up.

5.1 / 2

If no power supply is connected, the battery management

system automatically switches to UPS mode. This is indicated

by the “UPS” LED = red additionally lighting up.

5.1 / 3

☞ In order to switch off the battery management system, turn

the key switch to the OFF position. All LEDs will go out.

CAUTION!

The batteries also feed power after the mains plug has

been removed!

5. Product variants

6 – Battery management system UPS / Rev. B 0.2 Battery management system UPS / Rev. B 0.2 – 7

☞ Please connect the battery management system to a 400 V /

3~ power supply.

☞ Switch the battery management system on. The two LEDs

“BAT” = orange and “ON” = green should now light up.

5.2 / 2

If no power supply is connected, the battery management

system automatically switches to UPS mode. This is indicated

by the “UPS” LED = red additionally lighting up.

5.2 / 3

☞ In order to switch off the battery management system, turn

the key switch to the OFF position. All LEDs will go out.

CAUTION!

The batteries also feed power after the mains plug has

been removed!

5.2 USV 1000 - 1500 VA

5.2 / 1

H I

CAUTION!

As soon as the battery management system is connected

to a power supply, it will also feed power. This also applies

when the battery management system is switched off!

8 – Battery management system UPS / Rev. B 0.2 Battery management system UPS / Rev. B 0.2 – 9

5.3 USV 5000 - 7500 VA

5.3 / 1

GHI

CAUTION!

As soon as the battery management system is connected

to a power supply, it will also feed power. This also applies

when the battery management system is switched off!

☞ Please connect the battery management system to a 400 V /

3~ power supply.

☞ Switch the battery management system on by turning the

key switch to the ON position and holding it there for a few

seconds. The two LEDs “POWER” = blue and “ON” = green

should now light up.

5.3 / 2

If no power supply is connected, the battery management

system automatically switches to UPS mode. This takes

approx. 5 seconds and is indicated by the LED “ON” =

green and “UPS” = red lighting up.

5.3 / 3

☞ In order to switch off the battery management system, turn

the key switch to the OFF position and hold it there until all

LEDs go out.

CAUTION!

The batteries also feed power after the mains plug has

been removed!

Product variants

Battery management system UPS / Rev. B 0.2 – 9

8 – Battery management system UPS / Rev. B 0.2 Battery management system UPS / Rev. B 0.2 – 9

Type:

USV

750 VA

USV

1000 VA

USV

1500 VA

USV

5000 VA

USV

7500 VA

Output (VA): 750 1000 1500 5000 7500

Input

Phases: 1 (L1, N, PE) 3 (L1, L2, L3, N, PE) 3 (L1, L2, L3, N, PE) 3 (L1, L2, L3, N, PE) 3 (L1, L2, L3, N, PE)

Rated voltage (V): 230 400 400 400 400

Voltage range: ± 10% ± 10% ± 10% ± 10% ± 10%

Frequency range (Hz): 50 50 50 50 50

Output

Rated voltage (V): 230 400 400 400 400

Voltage range: ± 10% ± 10% ± 10% ± 10% ± 10%

Apparent power (VA): 750 1000 1500 5000 7500

Static voltage stability: ± 10% ± 10% ± 10% ± 10% ± 10%

Frequency range (Hz): 50 50 50 50 50

Weight (kg): 15 22 24 145 160

Dimensions, W x H x D (mm) 235 x 580 x 110 440 x 690 x 180 440 x 690 x 180 620 x 1250 x 190 620 x 1250 x 190

Noise emission (dBA (1m)): 54 54 54 54 54

Operating temperature (°C): +1 / +27 +1 / +27 +1 / +27 +1 / +27 +1 / +27

Relative humidity: < 95% non-con-

densing

< 95% non-con-

densing

< 95% non-con-

densing

< 95% non-con-

densing

< 95% non-con-

densing

Protection class (IP) 40 40 40 40 40

6. Technical data

10 – Battery management system UPS / Rev. B 0.2

Battery management system UPS / Rev. B 0.2 – 11

#161143

Marantec USV Owner's manual

Brand: Marantec

Model: USV

Category: Rechargeable batteries

Type: Owner's manual

USV 750 VA: Ideal for connecting to a 230 V / 1~ power supply.
USV 1000 - 1500 VA: Suitable for use with a 400 V / 3~ power supply.
USV 5000 - 7500 VA: Designed for higher power applications.

Download PDF

report

Marantec USV Owner's manual

Marantec USV Owner's manual

Related papers

Other documents