Trotec TDS 75 User manual

Category
Power heat guns
Type
User manual

Trotec TDS 75: With its powerful 5 kW heating output and adjustable thermostat, this electric heater is ideal for heating small to medium-sized rooms. Thanks to its integrated fan, the warm air is distributed evenly throughout the room, ensuring optimal heat distribution. The TDS 75 is also equipped with overheating protection and a tip-over switch for added safety.

Trotec TDS 75: With its powerful 5 kW heating output and adjustable thermostat, this electric heater is ideal for heating small to medium-sized rooms. Thanks to its integrated fan, the warm air is distributed evenly throughout the room, ensuring optimal heat distribution. The TDS 75 is also equipped with overheating protection and a tip-over switch for added safety.

TRT-BA-TDS75-TDS100-TDS120-TC210914TTRT01-010-EN
TDS 75 / TDS 100 / TDS 120
EN
ORIGINAL INSTRUCTIONS
ELECTRIC HEATER
2 EN
electric heater TDS 75 / TDS 100 / TDS 120
Table of contents
Notes regarding the instructions ..........................................2
Safety .....................................................................................2
Information about the device................................................5
Transport and storage...........................................................7
Assembly and start-up..........................................................7
Operation ...............................................................................8
Errors and faults....................................................................9
Maintenance ........................................................................10
Technical annex...................................................................11
Disposal ...............................................................................16
Declaration of conformity ...................................................16
Notes regarding the instructions
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning of hot surface
This symbol indicates dangers to the life and health of
persons due to hot surface.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information
(e.g. material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
instructions must be observed.
You can download the current version of the instructions via the
following link:
TDS 75
https://hub.trotec.com/?id=39786
TDS 100
https://hub.trotec.com/?id=42382
TDS 120
https://hub.trotec.com/?id=42383
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use.
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged from
8years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
EN 3
electric heater TDS 75 / TDS 100 / TDS 120
Warning
Children of less than 3years should be kept away from
the device unless continuously supervised.
Children aged from 3years and less than 8years shall
only switch on/off the appliance provided that it has
been placed or installed in its intended normal
operating position and they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved.
Children aged from 3years and less than 8years shall
not plug in, regulate and clean the appliance or
perform user maintenance.
Warning
Do not use the device in small rooms if persons are
present who cannot leave the room independently and
who are not under constant supervision.
Do not use the device in potentially explosive rooms or
areas and do not install it there.
Do not use the device in aggressive atmosphere.
Only put up the device in an upright, stable position on firm
ground.
Let the device dry out after a wet clean. Do not operate it
when wet.
Do not use the device with wet or damp hands.
Do not expose the device to directly squirting water.
Never insert any objects or limbs into the device.
Do not cover the device during operation.
Do not remove any safety signs, stickers or labels from the
device. Keep all safety signs, stickers and labels in legible
condition.
Do not sit on the device.
This device is not a toy. Keep away from children and
animals. Do not leave the device unattended during
operation.
Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any
defective devices or device parts.
Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Never
use the device if electric cables or the power connection
are damaged!
The mains connection must correspond to the
specifications in the Technical annex.
Insert the mains plug into a properly fused mains socket.
Observe the device's power input, cable length and
intended use when selecting extensions to the power
cable. Completely unroll extension cables. Avoid electrical
overload.
Before carrying out maintenance, care or repair work on
the device, remove the mains plug from the mains socket.
Hold onto the mains plug while doing so.
Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.
Do not under any circumstances use the device if you
detect damages on the mains plug or power cable.
If the power cable is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Defective power cables pose a serious health risk!
When positioning the device, observe the minimum
distances from walls and other objects as well as the
storage and operating conditions specified in the Technical
annex.
Keep a safety distance of at least1m between the air inlet
and the air outlet of the device and all combustible
materials such as textiles, curtains, beds and sofas.
Make sure that the air inlet and outlet are not obstructed.
Do not place the device on combustible ground.
Only use original spare parts, for otherwise safe and
functional operation cannot be ensured.
Allow the device to cool down before transport and/or
maintenance work.
Do not use the device if it has been dropped or if it shows
visible signs of damage.
Do not use the heating device together with a
programming device, a timer, a separate remote control
system or any other device that automatically switches the
heating device on, as there is a risk of fire if the heating
device is covered or incorrectly positioned.
Intended use
Only use the device for heating closed rooms whilst adhering to
the technical data.
Intended use comprises heating the air in:
Construction trailers
– greenhouses
– Boathouses
– Garages
Market stalls
– Workshops
Gastronomy sector
Warehouses and halls
– Shipyards
in wet rooms in compliance with the local or national
regulations for the operation of electrical equipment in
wet rooms.
4 EN
electric heater TDS 75 / TDS 100 / TDS 120
Foreseeable misuse
Do not place any objects, e.g. clothing, on the device.
Do not use this device in the vicinity of fuel, solvents,
varnishes or other easily inflammable vapours or in rooms
where these substances are stored.
Do not use the device out of doors.
Do not use the device for heating in vehicles.
Do not use the heating device in immediate vicinity of
swimming pools, bathtubs and showers.
Do not place the device on wet or flooded ground.
Any use other than the intended use is regarded as a
reasonably foreseeable misuse.
Do not make any unauthorised modifications, alterations or
structural changes to the device.
Personnel qualifications
People who use this device must:
be aware of the dangers that occur when working with
electric devices in damp areas.
have read and understood the instructions, especially the
Safety chapter.
Maintenance tasks which require the housing to be opened
must only be carried out by specialist electrical companies or by
Trotec.
Symbols on the device
Symbols Meaning
This symbol located on the device indicates that it
is prohibited to place objects (such as towels,
clothes etc.) above or directly in front of the
device.
In order to avoid overheating and fire hazards, the
heater must not be covered.
Residual risks
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket!
Do not touch the mains plug with wet or damp hands.
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Warning of electrical voltage
Risk of electric shock!
Risk of an electric shock if the heating device comes
into contact with water in bathtubs, showers or
swimming pools!
Do not use this heating device in immediate proximity
to bathtubs, showers or swimming pools!
Warning of hot surface
Parts of this appliance can become very hot and cause
burns. Particular attention is to be paid when there are
children or vulnerable persons present!
Warning
Improper handling entails a risk of burning and electric
shock.
Only use the device as intended!
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Warning
Improper installation entails a risk of fire.
Do not place the device on combustible ground.
Do not place the device on high-pile carpets.
Warning
In order to avoid overheating and fire hazards, the
device must not be covered!
EN 5
electric heater TDS 75 / TDS 100 / TDS 120
Behaviour in the event of an emergency
1. Switch the device off.
2. In an emergency, disconnect the device from the mains
feed-in: Hold onto the mains plug while pulling the power
cable out of the mains socket.
3. Do not reconnect a defective device to the mains.
Overheating protection
The device is provided with a safety thermostat, which is
activated by overheating of the device. In such an event the
device switches off automatically.
When the safety thermostat is activated, allow the device to cool
down. Only then start to look for the cause of overheating.
Should the problem persist, please contact the customer
service.
Information about the device
Device description
The electric heater serves to generate and distribute warm air,
e.g. in interior spaces.
The device generates heat by means of a heating element.
The air surrounding the heating element is heated. The heated
air is blown into the room by a fan.
The device is equipped with an integrated thermostat and so
generates a constant flow of warm air.
Fan operation without heating function is also possible.
Device depiction
TDS 75
TDS 75
15 kW
RESET
1
2
3
4
5
6
6 EN
electric heater TDS 75 / TDS 100 / TDS 120
TDS 100
TDS 100
22 kW
RESET
1
2
3
4
5
6
TDS 120
TDS 120
30 kW
1
2
3
4
No. Designation
1 Rotary switch temperature
2 Air outlet
3 Selection switch ventilation and heating levels
4 Carrying handles
5 Air inlet
6 Air baffle
EN 7
electric heater TDS 75 / TDS 100 / TDS 120
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
To make the device easier to transport, it is fitted with a carry
handle.
Before transporting the device, observe the following:
Switch the device off.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Do not use the power cable to drag the device.
Allow the device to cool down sufficiently.
Storage
Before storing the device, proceed as follows:
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Allow the device to cool down sufficiently.
When the device is not being used, observe the following
storage conditions:
Store the device in a dry location and protected from frost
and heat.
Store the device in an upright position where it is protected
from dust and direct sunlight.
If required, use a cover to protect the device from invasive
dust.
Place no further devices or objects on top of the device to
prevent it from being damaged.
Assembly and start-up
Scope of delivery
1 x Electric heater
1x manual
Unpacking the device
1. Open the cardboard box and take the device out.
2. Completely remove the packaging.
3. Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during
unwinding.
Start-up
Info
Odours might arise upon initial start-up or after a
longer period of non-use.
When positioning the device, observe the minimum distance
from walls or other objects as described in the chapter
Technical annex.
A
B
C
C
D
Before restarting the device, check the condition of the
power cable. If there are doubts as to the sound condition,
contact the customer service.
Set the device up in an upright and stable position.
Do not create tripping hazards when laying the power
cable or other electric cables, especially when positioning
the device in the middle of the room. Use cable bridges.
Make sure that extension cables are completely unrolled.
Make sure that no curtains or other objects interfere with
the air flow.
Make sure that the device cannot come into contact with
moisture or water.
Connecting the power cable
Insert the mains plug into a properly fused mains socket.
Make sure that the power cable is guided along the back
of the device. Never guide the power cable along the front
of the device!
8 EN
electric heater TDS 75 / TDS 100 / TDS 120
Operation
Avoid open doors and windows.
Control panel
TDS 75
TDS 75
15 kW
RESET
7
1
3
No. Designation
1 Rotary switch temperature
3 Selection switch for ventilation and heating levels
0: The device is switched off.
: ventilation only
: heating level 1
: heating level 2
: heating level 3
7 Reset button
TDS 100
TDS 100
22 kW
RESET
13
7
TDS 120
TDS 120
30 kW
13
No. Designation
1 Rotary switch temperature
3 Selection switch for ventilation and heating levels
0: The device is switched off.
: ventilation only
: heating level 1
: heating level 2
7 Reset button (TDS 100 only)
Info
In the event of a power failure, press the reset
button(7) after the mains plug has been removed from
the mains socket and after the device has been
switched off due to overheating.
Switching the device on
Once you have completely installed the device as described in
the chapter Assembly and start-up, you can switch it on.
1. Set the selection switch ventilation and heating levels(3)
to the desired heating level.
Setting the room thermostat
1. Turn the room thermostat's infinitely variable rotary switch
temperature(1) to the desired temperature range.
The room thermostat controls the room temperature
automatically:
When the set value is exceeded, the heating switches off
while the fan keeps running.
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
Turn the selection switch ventilation and heating levels(3)
to ventilation .
Keep the fan running for 3minutes before switching the
device off.
Switch off the device by setting the selector switch
ventilation and heating levels(3) to the0position.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Allow the device to cool down completely.
Clean the device according to the Maintenance chapter.
Store the device according to the Transport and storage
chapter.
EN 9
electric heater TDS 75 / TDS 100 / TDS 120
Errors and faults
Warning of electrical voltage
Tasks which require the device to be opened must
only be carried out by authorised specialist
companies or by Trotec.
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
The device does not start:
Check the power connection.
Check the power cable and mains plug for damage. If you
notice damages, do not try to take the device back into
operation.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Check the on-site fusing.
TDS 75 and TDS 100: The internal thermostat does not
reset automatically. Actuate the reset button(7) next to the
rotary switch temperature(1).
The motor might be defective. Have a defective motor
replaced by a specialist electrical company.
The room thermostat might be defective. Have a defective
room thermostat replaced by a specialist electrical
company.
Wait for 10minutes before restarting the device. If the
device is not starting, have the electrics checked by a
specialist company or by Trotec.
The device is switched on, the fan is operating, the heating
is not:
Check the room temperature. The room thermostat may
have switched off, because the desired room temperature
has been reached.
Check whether the overheating protection has tripped (see
chapter Safety).
The heating resistor might have blown. Have a defective
heating resistor replaced by a specialist electrical
company.
The room thermostat might be defective. Have a defective
room thermostat replaced by a specialist electrical
company.
The fan is not running:
Check whether the device is switched on.
Check the power connection.
Check the power cable and mains plug for damages.
The fan motor might be defective. Have a defective fan
motor replaced by a specialist electrical company.
The air current is reduced:
Check the air inlet and outlet. Make sure that air inlet and
outlet are not obstructed. Remove any dirt. Observe the
minimum distance from walls or other objects according to
the technical data.
The device is loud or vibrates:
Check whether the device is set up in a stable and upright
position.
Note
Wait for at least 3minutes after maintenance and
repair work. Only then switch the device back on.
The device still does not operate correctly after these
checks:
Please contact the customer service. If necessary, bring the
device to an authorised specialist electrical company or to
Trotec for repair.
10 EN
electric heater TDS 75 / TDS 100 / TDS 120
Maintenance Maintenance intervals
Maintenance and care interval before every
start-up
as needed at least every
2weeks
at least every
4weeks
at least every
6months
at least
annually
Check air inlets and outlets for dirt
and foreign objects and clean
ifnecessary
X
Check air inlet grid(s) for dirt and
foreign objects and clean
ifnecessary
X X
Clean the exterior X X
Visually check the inside of the
device for dirt
X X
Check for damage X
Check attachment screws X X
Test run X
Maintenance and care log
Device type: ............................................. Device number: ....................................
Maintenance and care interval 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Check air inlets and outlets for dirt
and foreign objects and clean
ifnecessary
Check air inlet grid(s) for dirt and
foreign objects and clean
ifnecessary
Clean the exterior
Visually check the inside of the
device for dirt
Check for damage
Check attachment screws
Test run
Comments
1. Date: ...................................
Signature: ................................
2. Date: ....................................
Signature: .................................
3. Date: ....................................
Signature: .................................
4. Date: ....................................
Signature: .................................
5. Date: ...................................
Signature: ................................
6. Date: ....................................
Signature: .................................
7. Date: ....................................
Signature: .................................
8. Date: ....................................
Signature: .................................
9. Date: ...................................
Signature: ................................
10. Date: ..................................
Signature: .................................
11. Date: ..................................
Signature: .................................
12. Date: ..................................
Signature: .................................
13. Date: .................................
Signature: ................................
14. Date: ..................................
Signature: .................................
15. Date: ..................................
Signature: .................................
16. Date: ..................................
Signature: .................................
EN 11
electric heater TDS 75 / TDS 100 / TDS 120
Activities required before starting maintenance
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
Switch the device off.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Allow the device to cool down completely.
Warning of electrical voltage
Tasks which require the device to be opened must
only be carried out by authorised specialist
companies or by Trotec.
Cleaning the housing
Warning of electrical voltage
Never immerse the device in water!
Clean the housing with a soft, damp and lint-free cloth. Make
sure that no moisture enters the housing. Protect electrical
components from moisture. Do not use any aggressive cleaning
agents such as cleaning sprays, solvents, alcohol-based or
abrasive cleaners to dampen the cloth.
Wipe the housing dry after cleaning.
Technical annex
Technical data
Parameter Value
Model TDS 75 TDS 100 TDS 120
Heating
capacity
level1:
level2:
level3:
level4:
Ventilation only
5000W
10000W
15000W
Ventilation only
11000W
22000W
-
Ventilation only
15000W
30000W
-
Air flow rate 1293m3/h 1632m3/h 1980m3/h
Operating
range
-20°C to
+45°C
-20°C to
+45°C
-20°C to
+45°C
Mains
connection
3/N/PE ~
400 V / 50 Hz
3/N/PE ~
400 V / 50 Hz
3/N/PE ~
400 V / 50 Hz
Max. power
input
15000W 22000W 30000W
Nominal
current
consumption
21.7 A 32 A 43 A
Fusing 32 A 35 A 50 A
Plug type CEE32 A,
5-pin
CEE63 A,
5-pin
CEE63 A,
5-pin
Type of
protection
IP24 IP24 IP24
Sound
pressure level
(at a distance
of 1m)
60 dB(A) 73 dB(A) 73 dB(A)
Weight 15 kg 20 kg 25 kg
Dimensions
(lengthx
widthx height)
332 x 405 x
540 (mm)
430 x 440 x
610 (mm)
485 x 530 x
785 (mm)
Minimum
distance to
walls and
other objects
top(A):
rear(B):
sides(C):
front(D):
50cm
50cm
50cm
50cm
50cm
50cm
50cm
50cm
50cm
50cm
50cm
50cm
12 EN
electric heater TDS 75 / TDS 100 / TDS 120
Circuit diagram TDS75
Circuit diagram TDS100
Circuit diagram TDS120
EN 13
electric heater TDS 75 / TDS 100 / TDS 120
Overview of spare parts TDS75 Note!
The position numbers of the spare parts differ from those
describing the positions of the components mentioned in these
instructions.
Spare parts list TDS75
No. Spare part No. Spare part
1 Front Grill (SPCC) 15 Socket Fixing Plate (SECC)
2 Tubular Electric Heating Element (230V AC 3000W) 16 Industrial Plug (400V 32A 5 Core)
3 Knob (PA) 17 Air Inlet Grill (SECC)
4 Control Panel (SPCC) 18 Left Handle (SPCC)
5 Heat Insulation Plate (SECC) 19 Right Handle (SPCC)
6 Left Panel (SPCC) 20 Plastic Gasket (PA)
7 Rotary Switch (250V 16A) 21 Motor (400V 50Hz 95W)
8 Insulation Plate (Epoxy Resin) 22 Air Passage (SECC)
9 Thermostat With Probe (400V 32A 40°/140°) 23 Fan (Ø300)
10 Time Delay Thermostat (250V 10A K45) 24 Right Panel (SPCC)
11 Middle Panel (SECC) 25 Bottom Panel (SPCC)
12 Top Cover (SPCC) 26 Tubular Electric Heating Element Upper Support
(SECC)
13 Protection Bush (PVC) 27 Tubular Electric Heating Element Lower Support
(SECC)
14 Lock (PA6) 28 Sensor Clip (Steel)
14 EN
electric heater TDS 75 / TDS 100 / TDS 120
Overview of spare parts TDS100 Note!
The position numbers of the spare parts differ from those
describing the positions of the components mentioned in these
instructions.
Spare parts list TDS100
NO. SPARE PART NO. SPARE PART
1 Top Panel 11 Heating Element
2 Inter Panel 12 Thermostat
3 Left Panel 13 Insulated Panel
4 Front Grill 15 Switch
5 Back Grill 16 Relay
6 Control Panel 17 Plug
7 Right Panel 18 Fan
8 Fan Blowing 19 Motor
9 Handle 20 Screws
10 Buttom Panel 23 Knob
EN 15
electric heater TDS 75 / TDS 100 / TDS 120
Overview of spare parts TDS120 Note!
The position numbers of the spare parts differ from those
describing the positions of the components mentioned in these
instructions.
Spare parts list TDS120
No. Spare part No. Specifications
1 Front Grill (SPCC) 19 Left Panel (SPCC)
2 Knob (PA) 20 Plastic Gasket (PA)
3 Control Panel (SPCC) 21 Fan (Ø 350mm)
4 Mica Sheet (0,9mm) 22 Motor ( YSK-70-4 400V 50Hz)
5 Rotary Switch (IK233-4/250V15A) 23 Air Inlet Grill (SPCC)
6 Temperature Controller (YT-WN16 250V/16A/85°C) 24 Air Inlet Grill Fixing Plate (SECC)
7 Insulation Palte (Epoxy Resin) 25 Before The Steel Tube (Ø 19*1.0mm)
8 Time Delay Thermostat (KSD301/250V/10A/K45) 26 After The Stell Tube (Ø 19*1.0mm)
9 Re-set Thermostat (KSD301-V/250V/16A) 27 Tupe Cap (Ø 19 mm/PA)
10 Contactor (HLC-3XWO4BBC 400V 50A 50Hz) 28 Right Panel (SPCC)
11 Relay (JQX-76F-TU-2A 380-400V AC 25A) 29 Pull Rivet Nuts (M10)
12 Middle Panel (SECC) 30 Stopple (Ø10)
13 Air Passage (SECC) 31 Bottom Panel (SPCC)
14 Industrial Plug (400V 63V) 32 Rase Heat Insulation Plate (SECC)
15 Heat Insulation Plate (SECC) 33 Tubular Electric Heating Element Upper Support
(SECC)
16 Top Cover (SPCC) 34 Tubular Electric Heating Element Lower Support
(SECC)
17 Capacitor (CBB60/ 450V 5µ F) 35 Tubular Electric Heating Element Support (SECC)
18 Capacitor Stents (SECC) 36 Tubular Electric Heating Element (230V 5000W)
16 EN
electric heater TDS 75 / TDS 100 / TDS 120
Disposal
Always dispose of packing materials in an environmentally
friendly manner and in accordance with the applicable local
disposal regulations.
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity.
The addresses can be obtained from your municipality or local
administration. You can also find out about other return options
that apply for many EU countries on the website
https://hub.trotec.com/?id=45090. Otherwise, please contact an
official recycling centre for electronic and electrical equipment
authorised for your country.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.
Only for United Kingdom
According to Waste Electrical and Electronic Equipment
Regulations 2013 (2013/3113) devices that are no longer usable
must be collected separately and disposed of in an
environmentally friendly manner.
Declaration of conformity
Declaration of conformity in accordance with the ECMachinery
Directive 2006/42/EC, AnnexII, Part1, SectionA
We– Trotec GmbH– declare in sole responsibility that the
product designated below was developed, constructed and
produced in compliance with the requirements of the
ECMachinery Directive in the version 2006/42/EC.
Product model/ product: TDS 75
TDS 100
TDS 120
Product type: electric heater
Year of manufacture as of: 2021
Relevant EUdirectives:
2011/65/EU: 01/07/2011
2012/19/EU: 24/07/2012
2014/30/EU: 29/03/2014
2015/863/EU: 31/03/2015
Applied harmonised standards:
EN 55014-1:2017
EN 60335-1:2012/A13:2017
EN 60335-2-30:2009
EN 60335-2-30:2009/A11:2012
• EN61000-3-11:2000
EN 61000-3-12:2011
Applied national standards and technical specifications:
EN 55014-2:2015
EN 62233:2008
Manufacturer and name of the authorised representative of
the technical documentation:
Trotec GmbH
Grebbener Straße 7, D-52525 Heinsberg
Phone: +49 2452 962-400
Place and date of issue:
Heinsberg, 22.06.2021
Detlef von der Lieck, Managing Director
Trotec GmbH
Grebbener Str. 7
D-52525 Heinsberg
+49 2452 962-400
+49 2452 962-200
www.trotec.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Trotec TDS 75 User manual

Category
Power heat guns
Type
User manual

Trotec TDS 75: With its powerful 5 kW heating output and adjustable thermostat, this electric heater is ideal for heating small to medium-sized rooms. Thanks to its integrated fan, the warm air is distributed evenly throughout the room, ensuring optimal heat distribution. The TDS 75 is also equipped with overheating protection and a tip-over switch for added safety.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI