AVATAR SD301-2SH Installation guide

Brand: AVATAR

Model: SD301-2SH

Type: Installation guide

AVATAR SD301-2SH is an electronic drum kit that offers a realistic drumming experience with its mesh heads and a wide range of sounds. It features 3 cymbals, 5 toms, a snare, a bass drum, and a bass pedal, all of which are connected to a sound module that provides a variety of drum and percussion sounds. The kit is designed for both beginners and experienced drummers, and it is suitable for practice, recording, and live performances. With its compact design and easy setup, the AVATAR SD301-2SH is a great option for musicians looking for a portable and versatile electronic drum kit.

Drum Kit

Installation Manual V1.20

IMPORTANT NOTES

Please observe the following notes, but not limited to these notes!

● Do not place the kit under direct sunlight, near radiate heat devices, or

otherwise subject to temperature extremes. Excessive heat can deform

or discolor the kit.

● When moved from one location to another where the temperature and/or

the humidity is very diﬀerent, before the using, you must allow it to stand

for hours, until the condensation has completely evaporated.

● The unit is sensitive to electromagnetic signals, and so please don’t use

the unit close to the devices have high electromagnetic interference such

as TV, radio, remotecontrolledtoys, etc.

● Please don’t wash mesh head with any corrosive or detergent. In case

of smudge, you can take oﬀ the mesh head from the pad and ﬂush with

clear water and then use when it is absolutely dry.

● Please use the speciﬁed power adapter. The using of wrong adapter may

cause damage of the kit.

● Please must make sure well-grounded connection.

● Do not open the unit and analyze the parts.Do not make any changes for

any internal parts.The unit has not parts repairable for users.Any functional

wrong or damage, please deliver to the qualiﬁed repairing persons.

● The parts such as pads and mesh head are speciﬁed for avatar edrum,

please do not privately take replacement with others.Please only consult

to dealers or distributors when needing.

1. Installing tools

(1) a Knife（Provided by user）, to gash the box tapes.

(2) Drum Key (Please ﬁnd it in the bag of drumstick ), to install racks and djust pads.

2. STEPS：

(1) Open box with knife and take out of all the parts as below picture . Count them with below

List.

INSTALLATION INSTRUCTIONS

X 28” Toms

X 1 X 1

X 1

Module Signal Lines

External Cable

(For crash 2)

X 1Drum Key

X 3 X 1 X 1 X 1

X 1 X 1Bass Drum

X 5L-rod X 1Power Adapter

X 1

Module Tray

Bass Pedal

Cymbal Rods Hi-Hat ① Hi-Hat ② Hi-Hat ③

X 3 X 3 X 1

10” Toms 12” Cymbal 13” Cymbal

(The heavy cymbal is Hi-hat) (For Ride）

Beater

(2) Assemble the racks as below pictures，fastening screw after the assembling.

Pic.1

Note: Please make sure the rack reaches

the position as ① shown.

①

a b cd

e f g h

X 1 X 1 X 2 X 1

X 1 X 1 X 1 X 1

f. c.b.

Pic.3Pic.2

Pic.5Pic.4

(3) Fix the Hi-Hat.

Hi-Hat ③

Hi-Hat ①

③

②

(4) Fix the Kick.

(6) Fix the cymbals.

Note: Please put the groove of cymbal against the embossment of the stand.

(5) Fix the drums.

Pay attention to the direction of the cymbal

and controller to avoial interference.

Notice: Please install the kit and connect lines under power blackout!

(7) In the end, connect module and pads and cymbals with signal lines, and adjust the

parameters of module to suitable. (Please refer User Guide for adjusting module)

1. Drum Module

2. Hi-Hat

3. Hi-Hat Controller

4. Crash 1

5. 8” Tom 1

6. 8” Tom 2

7. Ride

8. Crash 2

9. 10” Tom 4

10. 10” Tom 3

11. 10” Snare

12. Bass Drum

13. Bass pedal

14. Hi-hat pedal

AVATAR SD301-2SH Installation guide

AVATAR SD301-2SH Installation guide

AVATAR SD301-2SH Installation guide

Related papers

Other documents