SloanLED 60S1D Installation guide

Brand: SloanLED

Model: 60S1D

Type: Installation guide

SloanLED 60S1D is a 24 VDC power supply designed for outdoor use, featuring NEC Class 2 Output and a wide operating ambient temperature range of -40º to 60º C. It offers dimming capabilities via voltage, resistor, or PWM, allowing for flexible control of LED brightness. The power supply is built with robust construction, including mounting tabs for secure installation and adequate ventilation to ensure optimal performance.

60S1D 24 VDC Power Supply PAGE 1 OF 2

Installation Guide for PN 701895-60S1D – NEC Class 2 Output

1. Tools required: Wire strippers,

drill, and screwdriver.

Supplies required: Conduit and

electrical enclosure for power supply

(if not placed in a sign made from

enclosure rated material), #8 pan

head screws, UL Listed PLTC cable,

UL Listed electrical wire connectors

(e.g., wirenuts), silicone.

Europe: Electrical enclosure

for power supply, M4 pan head

screws, PLTC cable, silicone, 3M™

Scotchlok™connectors.

3. Power Supply: Identify primary

wires, secondary wires, and

location of mounting tabs.

4. Mount Power Supplies:

Use mounting tab in corner to

secure power supply.

NOTE: Ensure adequate ventilation. Power supply operating ambient temperature is -40º to 60º C. Power supply must be mounted in an

enclosure (i.e., transformer can/raceway). Power supply spacing to thermoplastic, wood, ber, or other combustible type enclosure materials

shall be 1" (25 mm). Two or more adjacent power supplies shall not be mounted closer than 1" (25 mm) end to end or 4" (102 mm) side to side.

If mounted inside a sign cabinet, UL requires that cabinet is made from an enclosure rated material. Ensure power supplies are not overloaded by

verifying output current is less than 5 DC Amps. It is recommended to use photocells or light sensors to prolong life of power supply and to keep

unit at maximum operating efciency.

5. Connect Primary:

CAUTION: Have a licensed

electrician connect primary.

ATTENTION: Avoir un permis

électricien connecter primaire.

24 VDC Output: Red (V+) & Black (V-)

Dimming: Violet (Dimming+) & Pink (Dimming-)

Mounting Tabs

Primary Wires (Brown & Blue)

PAGE 2 OF 2

SloanLED Headquarters

5725 Olivas Park Drive, Ventura, CA, USA

888.747.4LED (888.747.4533) • info@SloanLED.com

SloanLED.com

SloanLED Europe b.v.

Argonstraat 110, 2718 SN Zoetermeer, NL

+31 88 12 44 900 • Europe@SloanLED.com

P/N 402718 Rev B 2021-06-22

Customer service and technical support

60S1D 24 VDC Power Supply

Installation Guide for PN 701895-60S1D – NEC Class 2 Output

Some or all of the products shown are covered by U.S. and foreign patents pending and covered by one of more of the following

U.S. patents issued: 6776504, 6969179, 7192157, 6932495, 7241031

SloanLED products carry a limited warranty.

For complete details refer to the warranty policy found at SloanLED.com

TROUBLESHOOTING

If sign is not functioning properly, check the following:

• Primary voltage is between 120-277 VAC

• Secondary voltage is 24 VDC

• Output current is 2.5 Amps or less

• Power supply is not overloaded (see power supply capacity chart in product installation guide or SloanLED.com)

• There are no shorts in secondary wiring

• All secondary connections are RED-TO-RED and BLACK-TO-BLACK

E215393

E336107

LED current (%)

1.2

0.8

0.6

0.4

0.2

2 4 6 8 10 12

Dimming voltage (V)

Dimming by voltage

LED current (%)

1.2

0.8

0.6

0.4

0.2

6K 10K 20K 30K 40K 50K 60K 70K 80K 90K 10 0K

Resistance (ohm)

Dimming by resistor

LED current (%)

1.2

0.8

0.6

0.4

0.2

0.2 0.4 0.6 0.8 11.2

Dimming PWM

Dimming by PWM

SloanLED 60S1D Installation guide

SloanLED 60S1D Installation guide

SloanLED 60S1D Installation guide

Related papers

Other documents