2. HANYOUNG NUX
  3. PL-D2B

HANYOUNG NUX PL-D2B Owner's manual

  • Hello! I'm a chat assistant that has read the HANYOUNGNUX Photo sensor PL-D2B user manual. I am ready to answer your questions about this device. This manual provides information on its functions such as distance setting, BGS, stable detection as well as safety precautions and technical specifications.
  • What is the maximum sensing distance of the photo sensor?
    What kind of light source does the photo sensor use?
    What is the response time of the photo sensor?
    What is the degree of protection against water?
    What type of control outputs does this sensor provides?
3 4
•Ifyoudonotfollowinstructioninthismanual,injuryordamageofpropertymayoccur.
•Pleasedonotuseoutdoor
(Itmaycauseofshortenthelifeoftheproductorelectricshock).
•Donotuseflammable,explosivegasenvironments.
Pleasedonotusethisproductatanyplacewherehaveoverspecificationof
vibrationandshock.
•Pleaseuseadryclothtowipeoffdustsanddonotusethinnerorsolvent.
•Powerswitchandfusearenotattachedtothisproduct.Pleaseinstallthemseparately
ontheoutside.
Warning
•Whencleaningthelensandthecase,pleaseuseadryclothandgentlywipethesurface.
Mustnotusesolventssuchasthinneroralcohol.
•Thesensorwireshouldbeseparatefromhighvoltagelineorpowerline.Havingthesame
pipeforwiringcanbecauseofmalfunction.
•
Thisproducthas(IP65)waterproofstructurebutdonowusepermanentunderwaterplace.
•Whenextendingthecable,pleaseusethickwire(atleastthickness㎟)andatthismoment,
pleasewatchoutforthevoltage-drop.
•
Whenusingthesensorunderthelightsuchasfluorescentlightingormercurylampwith
highfrequency,pleaseblockitwithalightrapandavoidthelensfromfacingthelightdirectly.
•When2unitsofthroughbeamtypeofphotosensorareused,itcanbecause
ofmalfunctionduetointerference.Pleasemakeenoughspaceandpleaseinstallthe
receiverandemitterpositionsarecrossed.
•IncaseofuseInductiveload(relay,coil),theinstantaneousloadincreases2timesandit
maybreakTR.So,pleasesetmaximumloadathalf.
•Outputhasovercurrentprotectioncircuitsoitblocksoutputwhenoutputishigherthan
ratedloadcurrent.Sopleaseset70%fromthemaximumload.
•Alotofdustspollutelensanditmaycauseofmalfunctionsopleaseavoidusingthis
productdustarea.
•Informationinthemanualmaychangedwithoutpriornotification.
•Whenusingtheswitchingpowersupplyasthepowersource,earththeframeground(F.G)
terminalandbesuretoconnectthenoiseeliminatingcondenserbetween0VandF.G.
Caution
Frame
Power
Supply
(SMPS) C(0.01㎌-0.1㎌/500V)
-Noiseeliminating
condenser-
Photo
Sensor
※Notfollowingsafetyissueswhichstatedabovemaycauseproducttobreakdownsousers
mustfollowthem.
•DistanceSettingtypeandBGS(Backgroundsuppression)function.
•Stabledetectionispossiblewithoutinfluencecolor&quality
ofdetectionobject.
•Longdetectiondistance(2m)andcanbeappliedinvariousfields.
•Builtinthereverseconnectionofpowerprotectingcircuitandbuilt
intheoutputbreakprotectingcircuit
•IP65Protectivestructure(IEC)
Characteristic
Specification
Model PL-D2B
Sensingmethod Distance-settable
Sensingdistance 0.2~2m
Sensingobject 200X200㎜Whitepaperwithnogloss
Powersupplyvoltage
12-24Vd.c±10%
Currentconsumption
30㎃max.
Controloutput
NPN/PNPopencollectorasynchronously,
Loadcurrent:150㎃d.cmax.(Resistiveload)
NPNresidualvoltage:1Vd.cmax.,PNPresidualvoltage:2Vd.cmax
Operationmode LightON/DarkON※SelectablebythemodeV/R
Responsetime 2㎳max.
Hysteresis Lessthan10%ofthesensingdistance
Lightsource
(Wavelength) InfraredlighteningLED(880nm)
Receivingpart 2photodiodes
Display Controloutdisplay:RedLED,Stabilitydisplay:GreenLED
Distancesetting Near/Far:Opticaldistanceadjustingvolume5cycles.
Protectivecircuit
Powerreverseconnectionprotectingcircuitandoutputbreakprotectingcircuit
Ambientillumination Sunlight:11,000lxmax.,Incandescentlamp:3,000lxmax.
Ambienttemperature
Operation:-20~60℃,Storage:-25~70℃(Withoutfreezing)
Ambienthumidity 35~85%RH(Withoutcondensation)
Protectivestructure IP65
Insulationresistance 20㏁min.(500Vd.cMega)
Dielectricstrength 1000Va.c(50/60Hzfor1min)
Vibrationresistance
10-55Hz,Doubleamplitude:1.5mmfor2hourseachinX.YandZdirections.
Shockresistance 500㎨3timeseachinX.YandZdirections.
Connectionmethod
Cableoutputtype,Numberofwires:4P,Thickness:Ø4mm,Length2m
Material Case:PC,Lens:PC
Accessory Bracket,Adjustabledriver,bolt,Nut.
Connectiondiagram
MK1801KE130109
Photo sensor
PL-D2B
Thank you for purchasing HANYOUNG product.
Please check whether the product is the exactly same as you ordered.
Before using the product, please read this instruction manual carefully.
Please keep this manual where you can view at any time
INSTRUCTION MANUAL
1381-3,Juan-Dong,Nam-GuIncheon,Korea.
TEL:(82-32)876-4697
FAX:(82-32)876-4696
http://www.hynux.net
HANYOUNGNUX CO.,LTD
HEADOFFICE
INDONESIA
FACTORY
JL.CEMPAKABLOKF16NO.02DELTASILICONII
INDUSTRIALPARK
LIPPOCIKARANGCICAU,CIKARANGPUSATBEKASI
17550INDONESIA
TEL:62-21-8911-8120~4FAX:62-21-8911-8126
PT. HANYOUNG ELECTRONIC INDONESIA
Safetyinformation
Beforeusingtheproduct,pleasereadthesafetyinformationthoroughlyanduseitproperly.Alerts
declaredinthemanualareclassifiedtoDanger,WarningandCautionbytheircriticality
DANGER
DANGERindicatesanimminentlyhazardoussituationwhich,ifnotavoided,willresultindeathorseriousinjury
WARNING
WARNINGindicatesapotentiallyhazardoussituationwhich,ifnotavoided,couldresultindeathorseriousinjury
CAUTION
CAUTIONindicatesapotentiallyhazardoussituationwhich,ifnotavoided,mayresultinminorormoderateinjury
Dimension
[Unit:mm]
3 4
Sensingobject Sensing
object
Sensing
object
Moving
direction Moving
direction
Moving
direction
Precautionsduringinstallation
Nameofeachpart
Characteristicofsensingdistance
Operationchart
Modesettingswitch
D.ON:DarkON
L.ON:LightON
Stability
indicator(GREEN)
Output
indicator(RED)
Distance
settingindicator
Distance
settingvolume
•Coloredpapersensingdistance
•Materialsensingdistance
Whensettingthesensingdistanceofwhitepaperas200cm
Whensettingthesensingdistanceofwhitepaperas100cm
Whensettingthesensingdistanceofwhitepaperas20cm
Whensettingthesensingdistanceofwhitepaperas200cm
Whensettingthesensingdistanceofwhitepaperas100cm
Whensettingthesensingdistanceofwhitepaperas20cm distancedistance
White Red Green Blue Gray Black
Blackcolorpaper
Rubber
Packingbox
Veneerboard
Whitecolorpaper
Whensettingthesensingdistanceofwhitepaperas200cm
Whensettingthesensingdistanceofwhitepaperas100cm
Whensettingthesensingdistanceofwhitepaperas20cm
Whensettingthesensingdistanceofwhitepaperas200cm
Whensettingthesensingdistanceofwhitepaperas100cm
Whensettingthesensingdistanceofwhitepaperas20cm distancedistance
White Red Green Blue Gray Black
Blackcolorpaper
Rubber
Packingbox
Veneerboard
Whitecolorpaper
Stabilityindicator(Green)
Controloutput(TR)
Outputindicator(Red)
Stabilityindicator(Green)
Controloutput(TR)
Outputindicator(Red)
Stabilityindicator(Green)
Controloutput(TR)
Outputindicator(Red)
Stabilityindicator(Green)
Controloutput(TR)
Outputindicator(Red)
StabilityindicatorbecomesONwhenanamountoflightexceedtheoperationleveland
becomes120%(stableL.ONarea).Itcanbeusedastheenvironmentalchangeaftersetup
orleveldownduringoperationandinitialoperationcheck.
<L.ONoperation>
<D.ONoperation>
Howtosetthedistance
No Howtosetthedistance Settingstate
Indicatorfordisplay
thesettingdistance
1
Removethesensingobjectand
turnthedistancesettingvolume
toMaxdirectionuntilrightbefore
theoperationindicatorbecomes
ON.Here,wewillreferthis
positionasthepositionA.If
operationindicatordoesnot
becomesONthenwewillrefer
themaximumpositionasA.
2
Placethesensingobjectinthe
sensingpositionandcheck
whethertheoperationindicator
andstabilityindicatorbecomeON.
Afterinspectingsuchthings,turn
thesettingvolumetoMindirection
untiltheoperationindicator
becomesOFF.Wewillreferthis
positionasthepositionB.
3
Settheindicatorofdistance
settingtofallinbetweenAand
Bbyturningthedistancesetting
volumetoMaxdirectionand
checkswhetheritisoperating
properly.Here,ifthestability
indicator(green)doesnot
becomesONevenaftersensing
acertainobjectthenthecause
ismaybeduetotheunstable
sensingsopleasere-checkthe
sensingmethod.
Photo-electricswitch Photo-electricswitch Photo-electricswitch
Background
object
Background
object
Background
object
Sensingobject
Sensingobject
Sensingobject
Photo-electricswitch Photo-electricswitch Photo-electricswitch
Background
object
Background
object
Background
object
Sensingobject
Sensingobject
Sensingobject
Photo-electricswitch Photo-electricswitch Photo-electricswitch
Background
object
Background
object
Background
object
Sensingobject
Sensingobject
Sensingobject
(A)
3
5
1
1
3
5
3(B)
(B)
(A)
(A)
3
5
1
1
3
5
3(B)
(B)
(A)
(A)
3
5
1
1
3
5
3(B)
(B)
(A)
·Pleaseuse⊖driverasabovepicturewhenyoudetachtopcoverfromthecase.
·Regardingtheinstallationdirectionofphotosensor,pleaseconsideraboutthemoving
directionofsensingobjectandinstallit(pleaserefertoanimagebelow)
Sensingobject
Objectwithgoodreflectivity
✽Ifanobjectwithgoodreflectivityisinpresentunderthephoto
sensorthenoperationmaybecomeunstable.Therefore,please
slantthesensorandplaceitjustlikeanimagebeloworhavea
gapbetweenthegroundandsensor.
·Pleasedonotletstrongraylightsuchassunlight,fluorescentlight,incandescent
lampandetctofallwithinthedirectionalangleofphotosensor.
·Wheninstallingthephotosensor,donotapplystrongforceonitbyusingtools
suchashammerandetc.Doingsomaydamagetheinternalfunctions.
·PleaseuseM4forscrew
·Thetighteningtorqueofscrewshouldbelessthan1.2N·m
/