SATCO NUVO 64-100 User manual

LED

RGBTW

INDOOR/OUTDOOR

TAPE

LIGHTS

Models: 64-100, 64-110, 64-111, 64-120, 64-121, 64-130, 64-131, 64-132,

64-133, 64-134, 64-135, 64-140, 64-141, 64-142, 64-143, 64-144, 64-145

INSTALLATION

AND

SAFETY

INSTRUCTIONS

IMPORTANT: Read before installing fixture. Retain for future reference.

WARNING: Risk of Fire or Electric Shock

• This tape lighting

is

only intended to be used with the products provided

in

the kit.

• Installation requires knowledge of luminaries electrical systems.

If

not qualified,

do

not attempt installation. Contact

a qualified electrician.

•

To

reduce risk of fire and over-heating, secure

all

connections.

• TURN

OFF

the electrical power before proceeding.

• The electrical rating of this product

is

120V/60Hz.

• The grounding and banding of the system shall be done

in

accordance with National Electric Code

(NEC)

Article

600

and local codes.

•

To

prevent wiring damage or abrasion,

do

not expose wiring to edges of sheet metal

or

other sharp objects.

• Do not damage any PCB conductive parts, squeeze or fold the LED tape light when installing.

•

Pay

attention to positive and negative polarities before installation, otherwise the

LED

tape light may be damaged.

• Prevent static electricity when installing. Avoid damp or wet exposure.

• This device

is

not intended for use with emergency exits.

CUTTING

Applies to indoor models only 64-100, 64-110, 64-

111,

64-

120,

64-121,

64-130,

64-131

, 64-132, 64-133, 64-

134,

64-135.

• Always disconnect the power supply before cutting.

LED

strips can

be cut as indicated

in

diagram.

Indoor Installation

"-

X

I X

I

Applies to models 64-100, 64-110, 64-

111

, 64-120, 64-121, 64-130,

64-131

, 64-132, 64-133, 64-134, 64-135.

STEP

1:

Clean surfaces carefully

(free from grease and dust)

before installing to ensure that the

double sided tape or adhesive

sticks properly to the surface.

Wood, powder-coated, structured

surfaces, glass, stainless steel etc.

are not recommended locations.

STEP

2:

Gently peel off the tape,

the adhesive tape may tear by

over stretching.

STEP

3:

Wearing an anti-static

ring, gently press PCB areas.

Do not press down on the

actual LEDs.

STEP

4:

Be careful to not step

on the

reel

if you unreel the

entire strip before installation.

Sa

t

co

Pr

oduc

ts, Inc.

Bren

twoo

d, NY

11

717

Outdoor Installation

Applies to models 64-140, 64-141, 64-142, 64-143, 64-144, 64-145. Use included brackets to install the tape.

There

is

no double-sided adhesive with these models.

CONNECTIONS

~

~=~--------1]

..

,

1f

Junction

Box

~===I-~-_-_-~-

~---------jl

lf

,I

AC100-240V

Operation

STEP

1:

Align white arrow on the controller's cable to [

+-]

symbol

on

LED

strip.

STEP

2:

Connect controller to the power supply or Junction Box.

NOTE: Actual controller appearance may vary .

BLACK

WHITE

GREEN

Wiring Diagram

BLACK

WHITE

GREEN

Fixture

STEP 3A: Plug the power supply into a power outlet.

STEP 3B: For Junction Box, shut OFF power at the circuit breaker.

Connect wires as shown

in

wiring diagram above. Make sure

all

wire connectors are secure. After wires are connected,

tuck

them

carefully inside the Junction Box and turn ON power.

Use the remote control or Starfish APP to control the light strip; such as to turn on and off, brightness and color change.

~ ~

►

~

-◄

t i

00

Manual Control

by

3 Buttons &

IR

Remote Control

C Adjust Brightness/Speed.

cJ.J

Press one time ON/OFF.

To

reset and put into

network pairing mode, press

and hold for 5 seconds.

M Change mode type

(8

mode options).

Brightness-

Brightness+

--

◊®

•

®0®0

0008

Static

mode

--+-

0 0 0 (CT\

'

(i;

2

000®

0000

Colored light/Cold

White light

ON/OFF

Cool

White

Warm White

Color

temperature+

-Color

temperature-

Dynamic mode

SYSTEM REQUIREMENTS

• Minimum iOS 9.3

or

Wi-Fi 4.4

• Dedicated 2.4GHz Wi-Fi

Network

TECHINCAL SUPPORT

support

@satcostarfish.com

II

DOWNLOAD

THE

STARFISH

APP

GET

ITON

~

Google

Play

,

Download

on

the

• App Store

(App

design

is

subject

to

change

without

notice.)

Verify

you're

connected

to

a

2.4GHz

Wi-Fi

Network.

II.II

Launch

the

STARFISH

app

and

tap

llill

"Sign-up"

to

create

a

new

account

or

"Login"

to

your

existing

account.

■

Enter

email

address,

then

select

"Get

verification

code".

<

Register

United

States

of

America

1

Agroe

vaec

NKuroom

and

~..f.Qllr.y

II

Enter

verification

code

that

was

sent

to

your

email.

Enter Verification

Code

II

Tap

the

"Me"

button

at

the

bottom

of

the

screen

,

and

then

"Home

Management".

Select

the

II

Create

a

home

II

button

to

set

up

your

home.

c:J

More

Services

-

S!llat1

Cancel

Create

a

home

Home

Name

•

SATCO

~

Home

Locat

i

on

Edgewood

110

Heartland

B

lvd

Roorn~

Living

Room

Mas

t

er

Bedroom

Second

Bedroom

II

Tap

the(+)

button

on

the

top

right

•

corner

to

access

the

action

menu

,

then

select

"Add

Device"

.

II

Select

device

type

from

the

listed

categories.

(

Add

Manually

uto

S·an

..

Device, to

be

added

: 1

Do

no

t

add

Go

to add

P.11

To

put

the

device

into

pairing

mode

,

liil

press

and

hold

the

power

button

for

approximately

5

seconds

until

the

tape

light

starts

flashing,

then

release

the

button.

The

device

is

now

ready

to

be

paired

.

Cancel

EZ

Modo

1 8 a

Hold

tho

power butt

on

f

or

oppro,omately

5

r.econ<.ls

until

the

tape

light

starts

nash

1ng

,

lh

♦

n

rel4N1Sfl t

ha

bu

tt

on

Back

Ne

xt

~

f!l!I

Select

your

2.

4GHz

Wi

-

Fi

Network

lilil

name

and

enter

password

then

cl

i

ck

"

Select

2.4

GHz

WI-Fl

Network

and

enter

password.

101Jf

Y I

1J10

~I It

10

be

?

40~

ComlTIO!l

rout

er

•c

tt

i!'lg IMl

l'od

X Ill

~

V-,

F

2.4Ghz

The

pairing

status

screen

will

appear.

X

•- •

..

~

Starfish

Smart

4 •

Downllght

RG...

;

Once

device

is

successfully

paired,

continue

to

step

10.

PAIR A DEVICE WITH

WI-FI/BLUETOOTH

Note:

Verify

your

mobile

device

is

connected

to

a 2.

4GHz

Wi-Fi

Network

and

that

you

have

Bluetooth

turned

ON

for

connection.

l!P.I

For

Wi-Fi/Bluetooth

enabled

devic-

liil

es,

you

will

see

a

pop-up

indicating

that

there

are

unpaired

devices

in

the

area.

The

device

does

not

need

to

be

in

pairing

mode.

Tap

"

Add"

and

select

the

devices

you

would

like

to

connect.

(

Add

Device

~

lo<

Mffl)y

119'1:(ff

Ma_••

IU'e

J010

do-ilte

~

fflWCd

"Cl

>ode.

Dlsc:oll9fing

dtvlees-

Ad

d M

anually

"I

CD

._

I

,.

'IIJOdlii1t

°""""

Crrc~

~lqf

~

~-

"°"""

....

~

•

lil

@

CMloU

Cort,do

~_..S--

(M

ft

• I •

. .

..,

0.-l.ilil'll

'-'!I

Once

all

the

devices

have

lilil

connected

,

tap

"Next".

Found

1 devices. Added 1 successfully.

~

Start i

sh

Smart 4" Oownlight

RG

..

0

Once

device

is

successfully

paired

,

continue

to

step

10.

II

When

successfully

connected,

you

may

rename

the

device.

Tap

the

"Pen"

icon,

enter

the

new

name

and

select

"Done".

The

device

is

now

ready

to

be

controlled

with

the

STARFISH

app.

Do

Added

.

Device

added

successf

ufty

Living

Roon,

M:ister

Bedroom

Second

Bedroom

o,nrng

Room

Kitchen

Study

Room

Note:

If

pairing

is

unsuccessful,

please

refer

to

the

FAQs

on

Satco.

com/Starfish

Bluetooth

is

strictly

used

to

pair

and

connect

the

device.

A

2.4GHz

Wi-Fi

Network

is

required

to

operate

all

STARFISH

products.

Ill

From

the

Home

Management

screen,

select

the

Home

that

you

would

like

to

share.

Tap

"Add

Member"

and

select

the

way

that

you

would

like

to

send

the

invitation

< Home Management

Home

SATCO

~

Home

Member

e johnsmith

.....

•

4gma1!.com

Home

Owner

Add

Member ~

Enter

the

user

information

and

select

if

the

new

member

will

be

an

"Administrator"

or

a

11

Common

Member"

in

the

Home

.

Tap

"Save"

to

send

the

invitation.

Cancel

Add

Memb

er

Name

Region

United

States

of

America

Only

after accepting

the

invitatlor will the account

owner

become a

family rn£mber and

be

able

to

u5c

relevant functions.

Family

Role

........,.:i

~

..

STARFISH"

..

-

~~Fl~~T

6

FOOT

IN!lQOO

S

T~!P

IJCrtT

Location Prepared By

[www] 08-28-2023 02:49:40

Project Name

Notes

General

Status Active

Fixture Type Tape Light

Finish White

Wattage 68W

Lumen Output 6300L

IP Rating IP20

Indoor or Outdoor Fixture Indoor

Smart Product Info

IOT Enabled Yes

Voice Assistants Supported Google Home; Alexa; Siri;

SmartThings

Specifications

Technology LED

Color Temperature RGB and Tunable White

CRI 80+

Voltage 24V

Rated Hours 50000

Operating Temperature -20C (-4F) to +40C (+104F)

Dimmable Yes-Dimmable

Dimming Note Only with Starfish App or Remote

Control

Weight (lb.) 4.29

Material Plastic

Dimensions

Width (in.) 0.47

Length (in.) 787.44

Compliance

Safety Listing cETLus - Listed

Location Rating Dry

Energy Star No

DLC Approved No

CA T20 / T24 Rationale T20 Exempt - Fixtures Not

Regulated

California Status Lawful for sale in California

Title 20 / 24 Status Lawful for sale

California Prop 65 Lead

RoHS Compliant Yes

FCC Compliant Yes

SDS Sheet LED_Fixture

Additional Information

Additional Information Driver Wattage is 80W; Driver

Voltage is 120V-277V

Specification Note

Cuttable: Yes; Distance between

cuts: 4.92" (125 mm); High

Brightness; Sync to Music

Installation Notes

2 reels of 32 feet (10M) to make

64 feet (20M) total; 9 Foot (3M)

plug in tape pre-installed on back

for quick installation

Kit includes: Driver/Junction Box;

NUVO 64-135

TAPE/RGBTW-HO/IP20/JBOX/SF/64'

Includes Controller/Receiver; IR Remote; 2-

10M Reels

Warranty 1 Year Limited - Fixtures

http://www.satco.com/

11-

SUPPORT CENTER

>>

1

Year

Limited

-

Fixtures

This

Satco Products,

Inc.

product

is

warranted

to

be

free

from

defects

in

materials

and

workmanship

for

a

period

of

1 y

ear

from

date

of

origina

l purchase.

The

warranty

does

not

cover

damage

caused

by

abuse, misuse,

improper

environmenta

l

conditions,

wrong

insta

llation

or

shipping

damage.

If

this

does

not

last,

return

with

proof

or

purchase

,

register

receipt

with

your

name

& address, For

rep

l

acement.

This

rep

l

acement

is

the

sole

remedy

avail

ab

le

and

li

ab

il

it

y

for

incidental

or

consequentia

l

damages

is

hereby

expressly

exc

l

uded.

This

warranty

shall

not

apply

to

any

product

that

is

found

to

have

been

improper

ly

installed

,

set-up

,

or

used in

any

way

not

in accordance

with

the

instructions

supp

lied

with

the

product.

Satco does

not

warrant

and

specially disclai

ms

any

w

arranty,

w

hether

expressed

or

implied,

of

fitness

for

a

particu

l

ar

purpose,

other

than

the

warranty

contained herein.

Satco

speci

fically

disclaims

any

liability

and

shall

not

be

li

ab

le

for

any

consequential

or

incidental

l

oss

or

damage,

i

ncluding

any

l

abor

/ expense costs i

nvolved

in

the

replacement

or

r

epair

of

said

product.

SATCO NUVO 64-100 User manual

SATCO NUVO 64-100 User manual

Related papers

Other documents