ADDAC System ADDAC710 User guide

Brand
ADDAC System
Model
ADDAC710
Type
User guide

ADDAC System ADDAC710 is a dual balanced output module designed to isolate your modular system from external noise and interference. It features two independent channels, each with a toggle switch for selecting between lift, ground, or floating ground modes. The module also includes signal overload warning LEDs and XLR outputs. ADDAC710 is a cost-effective solution for reducing ground loop hum and other audio issues, making it ideal for live performances and studio recordings.

ADDAC System ADDAC710 is a dual balanced output module designed to isolate your modular system from external noise and interference. It features two independent channels, each with a toggle switch for selecting between lift, ground, or floating ground modes. The module also includes signal overload warning LEDs and XLR outputs. ADDAC710 is a cost-effective solution for reducing ground loop hum and other audio issues, making it ideal for live performances and studio recordings.

Instruments for Sonic Expression
Est.2009
August.2022
USER’S GUIDE . REV01
ADDAC710
BALANCED
OUTPUTS
INTRODUCING
From Portugal with Love!
ADDAC710 BALANCED OUTPUTS USER’S GUIDE
August.2022Revision.01
Welcome to:
page 2ADDAC SYSTEM
DESCRIPTION
ADDAC710 is a dual channel Isolated DI box and is all
about keeping the sound coming from your Modular free
from any undesired noisy interferences, making sure that
what you’re getting from your outputs is what your
Modular is actually producing. It provides galvanic
electrical isolation between the Modular system and
external sources preventing impedance mismatch and
ground loop induced hum.
ADDAC’s 710 circuit is designed around a unity 1:1 type
Low-cost Audio Transformer operating in the 20 Hz to 20
KHz range, this impedance matching transformer provides
two fully balanced outputs (via XLR connectors).
ADDAC710 is a low-cost alternative to our ADDAC800X
High-End Outputs module, we redesigned the original
circuit using a smaller low-cost transformer that also
reduced it’s depth allowing it to fit shallow Eurorack
cases.
There are two independent channels on the module with:
Audio Input
LIFT/FLOAT/GND toggle switch
Signal overload warning led
XLR Output
The LIFT/FLOAT/GND 3-way switch lets you choose
between lift, ground or floating ground.
In the LIFT position (left) the module circuit will be
“lifted” to ground through a 100R resistor and a 10nF
capacitor.
In the FLOAT position (middle) Ground will not be shared
leaving ins and outs grounds completely apart from each
other fully isolating both signals.
in the GND position (right) Ground will be shared between
inputs and outputs, here no isolation is used.
Any of these three positions may be the best form of
avoiding ground loops or any other undesired interference
occurring between your modular and the sound system
you’re plugging it into.
Try out which one of these options will work best in any
given situation.
This module will also be available as a full DIY kit..
Tech Specs:
6HP
4 cm deep
40mA +12V
40mA -12V
ADDAC710 User’s Guide
page 3ADDAC SYSTEM
TRANSFORMER FREQUENCY RESPONSE
20 Hz 50 Hz 100 Hz 20KHz10KHz1000 Hz
-0.5 dB
0.0 dB
0.5 dB
DESCRIPTION
The importance of using Audio Transformers
Applying a transformer balanced output isolation has lots of advantages over other less expensive ways
for dealing with ground loop issues. This method provides the chance to set a very simple and clean
circuit in which the signal transfer process develops smoothly and humming free. The transformer is a
device that performs both signal balancing and high-to-low (or vice-versa) impedance conversion, while
rejecting straggled DC voltage and Radio Frequency Interference from signal passing through a magnetic
bridge. In a transformer, two (or more) coils (called windings) of insulated wire wound around a magnet-
ic metal core allow for its input(s) and output(s) not to be physically connected together. When an AC
signal passes through the input winding (the primary), a perfectly related AC signal appears on the
output winding (the secondary). This way, by the fact that signal flows via inductive coupling between
the two windings of the transformer, this module presents a most accurate electrical isolation between
its input and output. A same number of windings on each coil guarantees that there’s no gain loss when
audio signal passes from the primary to the secondary windings. Furthermore, since these two windings
are insulated from each other, the transformer will electrically isolate ADDAC710 from any other device,
preventing hum problems coming from an outsider ground.
Being a low-cost transformer the frequency response curve is not as linear as our 800X, still the -0.2dB
attenuation at 50Hz feels negligible.
Phantom Power
+48V Phantom Power is NOT needed for the module to operate.
In any case having Phatom Power ON won’t influence the module operation.
CONTROLS DESCRIPTION
ADDAC710 User’s Guide
page 4ADDAC SYSTEM
Channel 1 Input
Channel 1 Grounding
Channel 2 Clipping Led
Channel 2 Output
Channel 1 Output
Channel 1 Clipping Led
Channel 2 Input
Channel 2 Grounding
For feedback, comments or problems please contact us at:
[email protected]
ADDAC710 USER’S GUIDE
August.2022Revision.01
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

ADDAC System ADDAC710 User guide

Brand
ADDAC System
Model
ADDAC710
Type
User guide

ADDAC System ADDAC710 is a dual balanced output module designed to isolate your modular system from external noise and interference. It features two independent channels, each with a toggle switch for selecting between lift, ground, or floating ground modes. The module also includes signal overload warning LEDs and XLR outputs. ADDAC710 is a cost-effective solution for reducing ground loop hum and other audio issues, making it ideal for live performances and studio recordings.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents