www.luminii.com T: 224-333-6033REV1.1 03072023 1 | 10
RGB, RGBW and RGBW Pixel
Plexineon Rings
Suspended MountSuspended Mount
3.40"
0.65"
1.50"
Ordering Code
MODEL RING DIAMETER1RING TYPE CCT OUTPUT LENS MOUNTING2FINISH POWERFEED
POSITION/TYPE
- - - - - - - -
PX - Plexineon ____ - Ring diameter in
inches, 6”-288”
(24ft)
HR - Horizonal Ring RGB
RGBW
RGBW-PXSPI
-
-
-
RGB
RGBW (3000K)
RGBW Pixel
Control (3000K)
SO - Standard F - Frosted SP
SPD
-
-
Suspension Mount, Standard Clips
Suspension Mount, Decorative Clips3
GG
BK
GY
WH
-
-
-
-
Gloss Grey
Matte Black
Matte Grey
Matte White
B-4 - Male Quick Connect
One End, Female Quick
Connect Other End
1. Rings will be made of equal sections no longer than 96” arc length. Tolerance on size of diameter is +/- 1”.
2. 2 mounting clips included for every 12” of diameter, with a minimum of 3 clips.
3. Decorative Clips match the fixture finish.
Without Mounting Clip With Mounting Clip
and A/C hardware
• Easy to install, for interior and exterior accent lighting
• Neon look providing a crisp, clear line of light visible
for miles
• Mounting Clips and aircraft cable are included in the
appropriate quantities
• Operating Temperature: -40° F to 140° F (-40° C to 60° C)
• 24VDC Class 2
• IK10 and 3G rated
• IP67 rated. IP68 rating available upon specific request
• 5 year warranty indoor, 3 year warranty outdoor
0.40"
1.44"
®
C US
Technical Information
RING OUTER DIAMETER*
(inch)
Plexineon
RGB
Plexineon
RGBW
Plexineon
Pixel RGBW
EFFICACY 17.5 lm/W 17.1 lm/W 14.7 lm/W
Ø36 (Ø3ft)
Lumen Output 679 lm 792 lm 792 lm
Power
Consumption 38.6 W 46.2 W 53.7 W
Ø72 (Ø6ft)
Lumen Output 1357 lm 1583 lm 1583 lm
Power
Consumption 77.2 W 92.3 W 107.4 W
Ø144 (Ø12ft)
Lumen Output 2714 lm 3166 lm 3166 lm
Power
Consumption 154.6 W 184.7 W 214.9 W
Ø288 (Ø24)
Lumen Output 5429 lm 6333 lm 6333 lm
Power
Consumption 309.1 W 369.5 W 429.8 W
*Rings will be made of equal sections no longer than 96” arc length. Rings exceeding 96W will have
allowances for additional power feeds.
Dominant Wavelength
Color RGB
Red 622nm
Green 525nm
Blue 468nm
RGBW (3000K)
Model TM-30
CRI RfRgR9
RGBW 85 84 98 22
RGBW -PXSPI
85 84 98 22
All channels full on.
www.luminii.com T: 224-333-6033REV1.1 03072023 2 | 10
RGB, RGBW and RGBW Pixel
Plexineon Rings
Suspended MountSuspended Mount
Used approximately every 30” of linear/arc
length for Standard Clips and every 18” of
linear/arc length for Decorative Clips
Use to join two fixtures together in the middle
of a Suspended Run
Used at the start of every Suspended Run Used to join two fixtures together and to drop
power in the middle of a Suspended Run
Suspension Hardware
• Suspension Hardware are included with Plexineon runs in the appropriate quantity, every 30” of linear/arc length for Standard Clips and every
18” of linear/arc length for Decorative Clips.
• Standard Clips have a stainless steel finish, Decorative Clip finishes match the fixture finishes.
SP/SPD
Finish Options
0X Clip Finish
00 Stainless Steel
01 Matte Black
02 Matte Grey
03 Matte White
Use for installation of Plexineon into Mounting Clips
SC-1MP2-SCL
Suspension Kit with Single Clip,
Ø2.0” canopy, 150” A/C Cable
SC-1MP2-DCL
Suspension Kit with Joiner Clip,
Ø2.0” canopy, 150” A/C Cable
SC-1FC5-SCL
Powerfeed Canopy Suspension Kit with
Single Clip, Ø5.0” canopy, 150” A/C Cable
SC-1FC5-DCL
Powerfeed Canopy Suspension Kit with Joiner
Clip, Ø5.0” canopy, 150” A/C Cable
70-TOL02-001-01
Mounting Clip Installation Tool
BK
Matte Black Finish
WH
Matte White Finish
GY
Matte Grey Finish
GG
Gloss Grey Finish
www.luminii.com T: 224-333-6033REV1.1 03072023 3 | 10
RGB, RGBW and RGBW Pixel
Plexineon Rings
Suspended MountSuspended Mount
Additional Material
• Ordered separately.
CC-2MF-190-SCL
Powerfeed Canopy Suspension Kit with Cross
Cable and 2 Single Clips Ø5.0” canopy
150” A/C Cable
CC-2MF-150-SCL
Powerfeed Canopy Suspension Kit with 2
Cables and Single Clips Ø5.0” canopy
150” A/C Cable
SC-2FC5-DCL
Dual Powerfeed Canopy Standard or
Decorative Joiner Clips
150” A/C Cable
Ring Types
Outer Diameter
Light Direction:
Forward
HR
Horizontal Ring
www.luminii.com T: 224-333-6033REV1.1 03072023 4 | 10
RGB, RGBW and RGBW Pixel
Plexineon Rings
Suspended MountSuspended Mount
Additional Material
• Connectors are included in the Plexineon runs per CCT option selected. Some CCT options may include multiple connectors per electrical
junction. Order extras as desired.
Male Quick Connect with flying leads can be
used to make wire jumpers
Use color suffix –08 for Black, -09 for Grey,
or –10 for White
Female Quick Connect with flying leads can
be connected to the Power Supply at the start
of a run. Can also be used with the Male
Quick Connect to make wire jumpers
Use color suffix –08 for Black, -09 for Grey,
or –10 for White
60-H-0002-08
Female Quick Connect
with flying leads, 2-conductor
60-H-0001-08
Male Quick Connect
with flying leads, 2-conductor
60-12-22AWGSBWN
Weatherproof Wire Nut
Silicone Filled
Male Quick Connect with flying leads can be
used to make wire jumpers
Only avaliable in color black
Female Quick Connect with flying leads can
be connected to the Power Supply at the start
of a run. Can also be used with the Male
Quick Connect to make wire jumpers
Only avaliable in color black
60-H-C3-0002-01
Female Quick Connect
with flying leads, 3-conductor
60-H-C3-0001-01
Male Quick Connect
with flying leads, 3-conductor
www.luminii.com T: 224-333-6033REV1.1 03072023 5 | 10
RGB, RGBW and RGBW Pixel
Plexineon Rings
Suspended MountSuspended Mount
SC-1FC5-SCL
SC-1MP2-DCL
SC-1MP2-SCL
60-H-C3-0002-01
60-H-C3-0001-01
Sample Layout
PX-48-HR-RGBW-PXSPI-SO-F-SP-GG-B-PFC
Plexineon Horizontal Ring, Suspended Mounting Clips
www.luminii.com T: 224-333-6033REV1.1 03072023 6 | 10
RGB, RGBW and RGBW Pixel
Plexineon Rings
Suspended MountSuspended Mount
MODELS PDCU-W
96W
PDCU-W
3X96W
PDCU-D
30W
PDCU-D
60W
PDCU-D
96W
PDCU-D
3X96W
Length 8.66" 11.85" 6.10" 7.93" 8.25" 9.57"
Width 3.73" 4.32" 3.35" 3.35" 4.10" 5.94"
Depth 1.61" 1.81" 1.33 1.32" 1.56" 1.13"
Universal Power Supply 1% 120VAC - 277VAC
MODEL POWER OUTPUT
--
PDCU-D -IP20 Dry Series 30
60
96
3X96
-
-
-
-
30 W
60 W
96 W
3X96 W
24-24 VDC
PDCU-W - IP66 Wet Series 96
3X96
-
-
96 W
3X96 W
0-10V dims down to 1%, MLV/ELV/TRIAC dims down to 1%.
For a complete list of compatible dimmers, see Compatible Dimming Chart on
the Resources page.
0-10V Dimming Power Supplies 0.1% 120VAC - 277VAC
MODEL POWER OUTPUT DIMMING
- - -
PS010V - 0-10V Power Supply
dims down to 0.1%
96
3X96
-
-
96 Wat t
3 X 96 Watt
24-24 VDC LIN
LOG
-
-
Linear
Logarithmic
MODELS 96W 3X96
Length 14.40" 15.75"
Width 5.20" 6.62"
Depth 2.60" 4.95"
24V DC+
24V DC-
LineLED
Load
Ground
Neutral
PDCU-W/PDCU-D
DIM +
DIM -
To 0-10V Dimmer
(if applicable)
LineLED
24V DC+
24V DC-
DIM +
DIM -
+
-
OUTPUT
0-10 controller wires to the next LED Driver
To 0-10v Dimmer
(if applicable)
PS010V-96
Load
Ground
Neutral
PS010V-3X96
LineLED
LineLED
96W Max
per terminal
24V DC+
24V DC-
24V DC+
24V DC-
24V DC+
24V DC-
Load
Ground
Neutral
+
-
OUTPUT
0-10 controller wires
to the next LED Driver
INPUT
120 - 277VAC
DIM +
DIM -
To 0-10v Dimmer
(if applicable)
Power Supplies
See Power Supply instructions and spec sheet for wiring information. For a complete list of compatible dimmers, see Compatible Dimming Chart on the Resources page.
Note: All Power Supplies come with one quantity of HS-STW01-50-00 (50ft of 14 Gauge wire black jacket, 2 conducters)
www.luminii.com T: 224-333-6033REV1.1 03072023 7 | 10
RGB, RGBW and RGBW Pixel
Plexineon Rings
Suspended MountSuspended Mount
Non-Dimming Power Supply 120VAC - 277VAC
MODEL POWER OUTPUT DIMMING LOCATION
- - - -
PSV - PSV Series 96-96 Wat t 24-24 VDC U2ND - Non Dimming D-Damp
MODELS 96W
Length 14.40"
Width 5.20"
Depth 2.60"
DALI 0% Dimming Power Supplies 120VAC - 277VAC
MODEL POWER OUTPUT
- -
PSDALI - DALI Power Supply
dims down to 0%
96
3X96
-
-
96 Wat t
3 X 96 Watt 24-24 VDC
Features eldoLED’s LINEARdrive configurable dimmable drivers
Model 96W 3X96
Length 14.40" 15.75"
Width 5.20" 6.62"
Depth 2.60" 4.95"
Load
Ground
Neutral 120 - 277VAC
PSDALI-96
lineLED 96 W max
24V DC+
24V DC-
OUTPUT
Dali controller wires
to the next LED Driver
To Dali
controller
INPUT
LineLED
LineLED
96W Max
per terminal
24V DC+
24V DC-
24V DC+
24V DC-
24V DC+
24V DC-
Load
Ground
Neutral
+
-
INPUT
120 - 277VAC
DIM +
DIM -
OUTPUT
Dali controller wires
to the next LED Driver
To Dali
controller
PSDALI-3X96
120 - 277VAC
lineLED 96 W max
24V DC+
24V DC-
Load
Ground
Neutral
PSV-96-24-ND-D
120 - 277VAC
To on/off Switch
INPUT
Power Supplies
See Power Supply instructions and spec sheet for wiring information. For a complete list of compatible dimmers, see Compatible Dimming Chart on the Resources page.
Note: All Power Supplies come with one quantity of HS-STW01-50-00 (50ft of 14 Gauge wire black jacket, 2 conducters)
DMX Dimming Power Supplies 120VAC - 277VAC
MODEL POWER OUTPUT
- -
PSDMX -DMX Power Supply
dims down to 0%
96
3X96
-
-
96 Wat t
3 X 96 Watt 24-24 VDC
Features eldoLED’s LINEARdrive configurable dimmable drivers
MODELS 96W 3X96
Length 14.40" 15.75"
Width 5.20" 6.62"
Depth 2.60" 4.95"
D-
GND
RGBW 96 W max
Load
Ground
Neutral
DMX cables
(For DMX cable,
use Belden 9829,
9842 or CAT5
shielded twisted
pair cabling
or equivalent) to the next
LED Driver
INPUT
120 - 277VAC
D+
+ R G B W
To Controller
PSDMX-96
Dynamic white lineLED
+
WW
CW
DMX cables
(For DMX cable, use
Belden 9829, 9842
or CAT5 shielded
twisted pair cabling or
equivalent)
Load
Ground
Neutral
INPUT
120 - 277VAC
D-
D+
GND
to the next
LED Driver
To Controller
96 W max per terminal block
RGBW
lineLED
+
R
G
B
W
PSDMX-3X96
+
-
www.luminii.com T: 224-333-6033REV1.1 03072023 8 | 10
RGB, RGBW and RGBW Pixel
Plexineon Rings
Suspended MountSuspended Mount
MODELS L3D0
Length 10.50"
Width 5.50"
Depth 2.00"
MODELS LTEA41UKL-CV240 L3DA4U1UKL-CV240
Length 4.89" 4.98"
Width 4.00" 4.00"
Depth 2.62" 2.62"
MODEL
LTEA4U1UKL- CV240
Lutron - Hi-lume™ 1% 2-wire LED Driver
40W max
(120V forward phase only)
MODEL
L3DA4U1UKL-CV240
Hi-lume™ 1% EcoSystem Voltage LED driver
40W max
Luminii is a Lutron OEM Advantage Partner
Lutron Power Supplies 1%
MODEL
L3D0-96W24V-U
Hi-lume™ 0.1% EcoSystem Voltage LED Driver with Soft-On, Fade-to-Black™
96W max
Luminii is a Lutron OEM Advantage Partner
Lutron Power Supplies 0.1%
In-Ground Power Supplies
MODEL POWER OUTPUT INPUT
- - - -
IG-In ground CVE Series CVE
DALI -
-ELV Dimming
eldoLED Dali
dimming
96X2 - 2 X 96 Watt 24-24 VDC Blank
277
-
-
120 V
240/277 V
Both dims down to 0%
MODELS Dual
Circuit
Length 8.40"
Width 8.30"
Depth 8.10"
E1
(Purple)
E2
(Purple)
To EcoSystem
Digital Link
Load
Ground
Neutral
24V DC+
24V DC-
L3DA4U1UKL-CV240
LineLED
To 2-wire
dimmer
Load
Ground
Neutral
24V DC+
24V DC-
LTEA4U1UKL-CV240
LineLED
To 2-wire
dimmer
Load
Ground
Neutral
24V DC+
24V DC-
LineLED
E1
(Purple)
E2
(Purple)
To EcoSystem
Digital Link L3D0-96W24V-U
lineLED 96 W max
24V DC+24V DC-
IG-CVE-96X2-24
Load
Neutral
LINE VOLTAGE INPUT
120V AC
(if applicable)
Power Supplies
See Power Supply instructions and spec sheet for wiring information. For a complete list of compatible dimmers, see Compatible Dimming Chart on the Resources page.
Note: All Power Supplies come with one quantity of HS-STW01-50-00 (50ft of 14 Gauge wire black jacket, 2 conducters)
www.luminii.com T: 224-333-6033REV1.1 03072023 9 | 10
RGB, RGBW and RGBW Pixel
Plexineon Rings
Suspended MountSuspended Mount
DMX Decoder
DMX signal to RGBW decoder (required to operate DMX controller) (for RGB and RGBW only)
Translates controller DMX512 programs for RGB and white LED strips.
Unique DMX address for the decoder can be set easily and displayed by the numeric display on
the case. Changing and resetting the DMX address requires manual input.
Use power repeater to expand output.
Operating Voltage
12-36 VDC
Power Capacity
up to 96W at 24V
Operating Temperature Range
from -4˚F to +122˚F in case
ORDERING CODE
MODEL
DDMX-RGBW
DDMX-RGBW - DMX decoder
DMX /Wireless RGB-W wall-mount controller controls DMX lighting fixtures, wireless control of
RGB-W lighting fixture or use both simultaneously. Fits in any standard US switch box. Includes all
the outputs in the back of the controller.
Control brightness levels with a single touch, personalize and memorize 3 different scenes, and
even create 3 variations of white.
Features
• 2 in 1 in-Wall Controller: DMX Control or
Wireless RGB-W
• 65,000 Color Options, Dimming and
Speed Control
• Memory Function
• 50 Foot Wireless Range
• Easily Fits Standard US Switch Boxes
• Touch Sensitive Glass Surface
• Includes 10 Built in Programs, or Create and
Play Your Own
Operating Voltage
12 - 24V DC
Color Parameters
• Brightness
• Saturation
• Primary colors
• Fading
• Color changing speed
DMX-1Z-RGBW, DMX-3Z-RGBW
RGBW LED 1 or 3 Zone Controller (for RGB and RGBW only)
ORDERING CODE
MODEL ZONES COLOR
- -
DMX - DMX
Controller
3Z
1Z
-
-
Three Zone
One Zone
RGBW - Red,
Green,
Blue,
& White
www.luminii.com T: 224-333-6033REV1.1 03072023 10 | 10
RGB, RGBW and RGBW Pixel
Plexineon Rings
Suspended MountSuspended Mount
Touch DMX Controller
Touchscreen digital LED controller
Programmable advanced DMX512 lighting controller featuring a touch-screen interface.
Operates as stand alone controller or integrated with most architectural lighting control
systems. Can controller endless DMX512 enabled devices.
Mounts to standard single or dual gang wall box with the included power supply inside
the junction box. Terminal block design for power and data connections.
Features
• Sleek glass design which sits 0.43” from the
wall
• Graphical color display to show selected
environment
• Color/dimmer/speed palette
• Color temperature mixing
• Touch sensitive buttons. No mechanical parts
• Touch sensitive wheel allows for accurate
color selection
• Multi-zone microSD memory
• Multi-room control with 500 scenes, 10
zones
• 1024 DMX channels. Control 340 RGB
fixtures
• USB & Ethernet connectivity for programming
and control
Power Supply
7 VDC (included)
Programmability
PC, Mac, Tablet, Smartphone
Output Signal
DMX512 (1024 channels)
Color Parameters
• Brightness
• Saturation
• Speed of color changing sequence
• Fading / dimming / brightness
ORDERING CODE
MODEL
TSDMX-E
TSDMX-E - Touchscreen DMX controller
The SR-DMX-SPI is a smart LED pixel decoder that controls
RGB/RGBW pixel LED strips with SPI signal. Designed with a digital display,
the pixel controller allows for easy configuration of most settings. Three push
buttons are available for control of the LED functions.
Operating voltage
5-24 VDC, Max 12A
Power capacity
up to 96W at 24V
Operating temperature range
from -4˚F to +122˚F in case
Features
- SPI signal output for RGB/RGBW
pixel light control
- DMX512 controllable
- 52 DMX decoding channels
- Works with integrated DMX
consoles and sequencing
software
- Display panel allows for easy
configuration
Model
SR-DMX-SPI
SR-DMX-SPI - Smart Pixel Decoder
Smart Pixel Decoder
PIXEL PLEXINEON
In
Out
(-)
(+)
POWER SUPPLY
(N)
(L)
CONTROLLER WIRES
1000 ft max,
decoder to Controller
AC
input
output
24VDC
32 ft max, decoder to strip
SPI signal to DMX signal decoder
MODELS SR-DMX-SPI
Length 6.93"
Width 1.8"
Depth 1.18"
/
