luminii LLDW73STP LineLED DW73STP Wet Location Linear LED Strip User manual
- Type
- User manual
LineLED DW73STP - Installation Instructions
Models LLDW73STP-
Please read all instructions prior to installation and keep for future reference!
1. Product should be installed by a qualied electrician.
2. Prior to installation ensure power is o at fuse box to prevent electrical shock.
3. Use only with Class 2 power unit. Utiliser seulement avec Classe 2 unite d’alimentation electrique.
4. Suitable for Damp Locations. Convient Aux Emplacements Humides.
5. For under-cabinet or shelf mount.
6. Conforms to UL STD 2108. Certied to CSA STD
C22.2 No.250.0.
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.0
03182021
1 / 3
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Attention: Always test LineLED operation before installing. Connect LineLED to power supply to ensure it is working properly and no damage has
occurred during shipping.
1
2 3
Note: When removing backing &
laying LineLED to surface avoid
ripples on LineLED.
Note: Avoid bending the LineLED in at
bends which may damage the LEDs
Clean the area thoroughly where the LineLED will be installed.
Remove the paper backing from the LineLED and rmly press down making sure there are no air
bubbles that can cause surface irregularities.
Do not remove the adhesive, removing the adhesive may cause arcing of the Line LED tape.
If length of LineLED needs to be adjusted on site, simply cut the
LED strip in between solder pads. Always cut from end with no
wire leads. Always ensure power to power supply is o!
Follow diagrams on page 2 to connect power
feed wires to power supply.
LineLED DW73STP - Installation Instructions
Models LLDW73STP-
Please read all instructions prior to installation and keep for future reference!
1. Product should be installed by a qualied electrician.
2. Prior to installation ensure power is o at fuse box to prevent electrical shock.
3. Use only with Class 2 power unit. Utiliser seulement avec Classe 2 unite d’alimentation electrique.
4. Suitable for Damp Locations. Convient Aux Emplacements Humides.
5. For under-cabinet or shelf mount.
6. Conforms to UL STD 2108. Certied to CSA STD
C22.2 No.250.0.
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.0
03182021
2 / 3
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
+
-
+
-
PRIMARY
24VDC
INPUT
SECONDARY WW
R
+
-
CW
G
+
-
WW
B
+
-
CW
W
+
-
Input
120V AC RGBW -RC-R receiverpower supply
24VDC
OUTPUT
+
-
120VAC
INPUT
L
N
Wireless
Controller
RGBW
L
N
GRD
Input
120-277V AC
D1
D2
D3
DMX
IN
DMX
OUT
+-
shield
n/a
3 x 96w DMX Power Supply
LLDW36 LINELED
100W MAX PER TERMINAL
Controller
- +
D- D+
GND
-
+
to Controller
power supply
DMX cables
(For DMX cable, use Belden
9829, 9842 or CAT5 shielded twisted
pair cabling or equivalent)
to the next
power supply!
n/a
+24
VDC
WW
CW
WW
CW
WW
CW
Wiring diagram using
PSDMX power supply
Wiring diagram using
PSV power supply
+
-
-
WW
CW
Operations to controller
1. Press the learning key on the receiver, then push the rotary button. Once successfully learn, the LED lights will blink on the
receiver. Do the same for the other receivers if you use them, you can add as many optional receivers as you want.
2. Short press once the rotary button to switch on/o. Adjust dim brightness by the rotary button from le to right 0.1 - 100%.
Adjust dim brightness by the rotary button from right to le 0.1 - 100%. Long press rotary button, the light will be 100%
brightness.
Double click rotary button, it will enter into dimming color temperature mode, dim WW & CW associatively, for example if WW
is 70%, CW is 30%. Double click again, will enter into dimming brightness mode.
LineLED DW73STP - Installation Instructions
Models LLDW73STP-
Please read all instructions prior to installation and keep for future reference!
1. Product should be installed by a qualied electrician.
2. Prior to installation ensure power is o at fuse box to prevent electrical shock.
3. Use only with Class 2 power unit. Utiliser seulement avec Classe 2 unite d’alimentation electrique.
4. Suitable for Damp Locations. Convient Aux Emplacements Humides.
5. For under-cabinet or shelf mount.
6. Conforms to UL STD 2108. Certied to CSA STD
C22.2 No.250.0.
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.0
03182021
3 / 3
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
gray-
purple+
Vin1-
black
Vin1+
red
warm+
yellow
warm-
blue
cool-
blue
cool+
yellow
Vin2-
black
Vin2+
red
SLD-DIM-TW
Tunable white LED PWM dimming module
Dimming range: 0-100%
0/1-10V control, 0/1V=0% light output
10V=100% light output
PWM Output to LED Modules (8-48V PWM, 1K Hz)
For use with Class 2 DC LED Driver only
connect to 0-10V
controller wires
Wiring diagram using 0-10 Warm
Dim 96 watt LED Driver
+
-
-
W W
CW
L
N
GRD
-
+
120 - 277V AC
LED Driver 96W max
connect
to 24VDC
reference LineLED wire lead
labels to determine polorarity
PS010WD-96-24 power supply
Wiring diagram using DDMX-RGBW
decoder 96 watt LED Driver
red
- +
green
- +
blue
- +
yellow
- +
input
+ -
GND
+ -
D1+ D1- D2+ D2-
DECODER
DYNAMIC WHITE
LineLED
(N)
(L) output
24VDC
POWER
SUPPLY
AC
input
DMX cables
(For DMX cable, use Belden
9829, 9842 or CAT5 shielded twisted
pair cabling or equivalent)
TO CONTROLLER
-
1
-
2
-
3
luminii LLDW73STP LineLED DW73STP Wet Location Linear LED Strip User manual
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
luminii LL42WET-T User manual
-
luminii LL36X2 User manual
-
luminii LLHE48WET-T User manual
-
-
-
-
luminii LLWD68 User manual
-
-
-