9 Before each use check all attachments for condition. If worn or damaged replace immediately.
8 DO NOTswitchthepolisheronuntiltheheadisincontactwiththepanelandswitchtheunitobeforeremovingtheheadfromthe
panel.
8 DO NOTusethepolisherwithabrasivecleanersorrubbingcompoundsasexcessivepaintremovalmayresult.
8 DO NOT get the polisher wet or use in damp or wet locations or areas where there is condensation.
8 DO NOT allow untrained persons to operate the polisher.
9 When not in use, unplug from the mains power supply and store in a safe, dry, childproof area.
2. INTRODUCTION
Digitaldisplayandvariablespeedcontrolfrom500-3000rpm.Featuresaslide-buttonon/oswitchallowingforasmoothcomfortablemain
handlegrip.Spindlelockforfastandeasypadchanges.Doubleinjectioncompositehousingwithrubbergripforaddedcomfort.Supplied
withØ150mmbackingpadandsidehandle.Requirescompatible20Vbatteryandmainscharger,soldseparately.
3. SPECIFICATION
Model No ...............................................................CP20VRP
Battery ................... 20V2Ah-6AhLithium-ion(notincluded)
Consumableparts:
PTC/150VA/M14-DABackingPadforHook-and-LoopDiscsØ148mmM14x2mm,
CP20VBP2-2AhBattery,CP20VBP4-4AhBattery,CP20VBP6-6AhBattery
Free speed ........................................................500-3000rpm
Noisepower/pressure .......................................... 85/74dB(A)
Padsize .................................................................. Ø150mm
Replacement parts:
............................. CP20VMC-MainsCharger(notincluded)
Threadsize ......................................................... M14x2mm
Vibration/uncertainty .......................................... 8.27/1.5m/s²
4. OPERATION
WARNING: Removebatterybeforetting/removingpadsormaintenanceiscarried out.
NOTE: Whennew,thebatteriesmayhavebeenshippedinalowchargestate. Fullychargethe
batteriesbeforeusingyourtool.
4.1. Ensure that you have read, understood and comply with all the safety instructions in
Section1.
4.2. POLISHING (FIG.1)
4.2.1. Holdingthepolisherrmlyoperatetheon/oswitch.
4.2.2. Tosettherotationalspeedofthepolisherusethe +/- buttons.Toincreasespeed,
press ‘ + ‘, to decrease press ‘ - ‘.
4.2.3. Thereare7speedsettingsavailableandthecurrentonebeingusedisshowninthespeedsettingdisplaywindow.Thevalues
displayedare5,8,10,15,20,25,and30.EachstepindicatesanRPMofapproximately100timesthevalueshown.
4.2.4. When polishing, DO NOTapplytoomuchpressure,theweightofthepolishershouldbesucient.AlsoDO NOT work for too long
inoneareaoryoumaydamagethesurfacebeingworkedon.
4.3. BACKING PAD EXCHANGE (FIG.2)
WARNING: Removebatterybeforetting/removingpadsormaintenanceiscarriedout.
4.3.1. Toremovethebackingpad,pressdownchucklockingbuttonandmanuallyunscrewthepadclockwise(whenviewedfromabove).
5. MAINTENANCE
WARNING: Alwaysdisconnectthebatterybeforecarryingoutanyinspection,maintenanceorcleaning.
5.1. GENERAL INSPECTION
5.1.1. Regularlycheckthatallthexingscrewsaretight.
5.1.2. Repairsshouldbecarriedoutbyanauthorisedservicecentre.
5.2. CLEANING
WARNING:Alwayswearprotectiveequipmentincludingeyeprotectionandgloveswhencleaningthistool.
5.2.1. Keepyourtoolcleanatalltimes.Dirtanddustwillcauseinternalpartstowearquicklyandshortenthedevice’sservicelife.
5.2.2. Cleanthebodyofyourmachinewithasoftbrush,ordrycloth.
5.2.3. Neverusecausticagentstocleanplasticparts.Ifdrycleaningisnotsucient,amilddetergentonadampclothisrecommended.
5.2.4. Watermustnevercomeintocontactwiththetool.Ensurethetoolisthoroughlydrybeforeusingit.
5.2.5. Ifavailable,useclean,drycompressedairtoblowthroughtheventilationholes(whereapplicable).
5.3. LUBRICATION
5.3.1. Lightlylubricateallmovingpartsatregularintervalswithasuitablelubricant.
5.4. STORAGE
5.4.1. Store this tool carefully in a secure, dry place out of the reach of children.
WARNING! – Risk of Hand Arm Vibration Injury.
ThistoolmaycauseHandArmVibrationSyndromeifitsuseisnotmanagedadequately.
ThistoolissubjecttothevibrationtestingsectionoftheMachineryDirective2006/42/EC.
Thistoolistobeoperatedinaccordancewiththeseinstructions.
Measuredvibrationemissionvalue(a)............................8.27m/s²
Uncertaintyvalue(k):......................................................1.5m/s²
Pleasenotethattheapplicationofthetooltoasolespecialisttaskmayproduceadierentaveragevibrationemission.We
recommendthataspecicevaluationofthevibrationemissionisconductedpriortocommencingwithaspecialisttask.
Ahealthandsafetyassessmentbytheuser(oremployer)willneedtobecarriedouttodeterminethesuitabledurationofusefor
each tool.
Original Language Version
© Jack Sealey Limited
g.1
g.2
CP20VRPIssue2(1,2,3)15/07/21