Acoustic Q-AV Rear User manual

Brand: Acoustic

Model: Q-AV Rear

Type: User manual

Acoustic Q-AV Rear is a 1-way reflex speaker with a 100mm drive unit. It has a frequency response of 60Hz - 20 kHz, a nominal impedance of 6 ohms, and a minimum impedance of 4 ohms. The speaker has a sensitivity of 88dB and is recommended for use with amplifiers with a power output of 25 - 75 watts. The Acoustic Q-AV Rear can be used as a rear speaker in a multi-channel surround system, or as a secondary speaker system for multi-room applications or in public areas such as restaurants and shops. It is not suitable for use as the main speaker in a hi-fi system.

User Manual and

Product Specifications

Q-AV Rear

The Q-AV Rear speaker acoustically matches the Q-AV LCR providing First remove the metal grille using the tool provided ‘H’. Hook the end of

rear ambient sound in a multi-channel surround system. This unique the tool through one of the grilles perforated holes in the side of the grille

speaker is designed to wall mount at low skirting board or ceiling level, and pull gently, the grille will come free.

the most convenient position for running cables. In either position it will

seamlessly integrate with the Q-AV LCR.

The Q-AV Rear speaker can also be used as a secondary speaker

system for multi-room applications or in public areas such as

restaurants, shops etc where low level background music is needed. It is

not suitable for use as the main speaker in a hi-fi system.

Installation

The Q-AV Rear speaker comes fitted with a desk stand and should

always be positioned with its back to the wall for optimum performance.

The performance will be impaired if the speaker is positioned away from

the rear wall. When the speaker is to be wall mounted remove the desk

stand by pulling gently.

To release the wall bracket from the back of the speaker remove screw

(J). Using the bracket as a template drill and plug the fixing holes in the

appropriate position and with screws capable of securing the weight of

the Q-AV Rear speaker.

Q-AV Rear Speaker

Introduction

If mounting at skirting board level measure 40mm up from the floor, for Supporting the loudspeaker, hook it onto the wall bracket and replace the

skirting boards in excess of 40mm rest the bracket on the top of the central fixing screw (J) to retain the speaker in place.

skirting board to fix its position.

Thread the speaker cable through the hole in the back of the speaker to

the connection terminals at the front. These are accessible under the

terminal cover (K). Make sure the cables are not reversed (+ goes to +)

or the speakers will play out of phase which will result in a thin, weak

sound . Terminate the cables securely and replace the terminal cover.

Similarly if the speaker is to be mounted at ceiling height measure 40mm

down from the ceiling or align with the edge of the coving if greater than

40mm. Note: the bracket is turned around 180 degree for ceiling

mounting.

Place the grille locating its edge in the groove around the perimeter of the

speaker front; push gently into position. The grille can be fitted either way

up so it is possible to keep the badge correctly orientated with the

speaker mounted at ceiling or skirting board level.

40mm MIN

Clean cabinets with a slightly damp cloth. The finish is sealed with a high Q Acoustics loudspeakers are warranted free of defects in materials and

quality sealant so that in normal use there is no need to use solvent

workmanship as follows:

based cleaning materials. If the cabinets become stained, remove the

Passive Loudspeakers: 3 years from the date of purchase.

stain with a cloth lightly moistened with water, white spirit or isopropyl

Active Loudspeakers & Subwoofers: 2 years from the date of purchase.

alcohol depending on the stain. Then lightly buff with a cloth to remove

any residue of the cleaning agent. Never use abrasives of any kind.

During the warranty period Q Acoustics will, at its option, repair or

replace any product found to be faulty after inspection by the company

Grilles

or its appointed distributor or agent.

Lightly brush out grilles with a soft brush. Do not remove the speaker

Misuse and fair wear and tear are not covered by warranty.

grilles unless absolutely necessary.

Goods for repair should in the first instance be returned to the supplying

Drive Units

dealer. If this is not possible the item/s should be sent carriage paid

Drive units are best left untouched as they are easily damaged when

preferably in the original packing, to Q Acoustics or their appointed

exposed.

distributor for your area and accompanied by proof of purchase.

Damage sustained by goods in transit to the repair centre is not covered

Licences

by warranty. Return carriage will be paid by Q Acoustics or their

NXT is a trade mark of New Transducers Limited.

distributor as appropriate.

This warranty does not in any way affect your legal rights.

Appointed Distributor in the UK:

Armour Home Electronics Ltd

Units 7 & 8, Stortford Hall Industrial Park

Bishops Stortford, Herts, UK

CM23 5GZ

For service information In other countries contact

[email protected]

Care and Cleaning

Warranty

Cabinet Care

Q Acoustics Q-AV Series Specifications

Enclosure type:

Drive Unit (mm):

Frequency response: (±3dB):

Nominal Impedance:

Minimum Impedance:

Sensitivity (2.83v@1m):

Recommended amplifier power:

Effective volume:

Cabinet dimensions (HxDxW mm):

Weight (per cabinet):

1-way reflex

100mm

60Hz - 20 kHz

6Ù

4Ù

88dB

25 - 100W

2.2 litres

h160 x d75 x w300

7.2Kg (x 3 Including Bracket)

1-way reflex

100mm

60Hz - 20 kHz

6Ù

4Ù

88dB

25 - 75W

2.0 litres

h240 x d105 x w205

1.3 Kg

Q-AV LCR Q-AV Rear

Enclosure type:

Bass Unit (mm):

Amplifier power:

Crossover frequency:

Cabinet dimensions (HxDxW mm):

Weight :

Ported

200 mm long throw

120 Watts

45Hz - 200Hz (var.)

h432 (450 with spike) x d170 x w475

15.75Kg

Active Speakers

Passive Speakers

Q-AV Subwoofer

www.qacoustics.co.uk

Acoustic Q-AV Rear User manual

Acoustic Q-AV Rear User manual

Acoustic Q-AV Rear User manual

Other documents