Elo TouchSystems ET3201L User manual

Brand: Elo TouchSystems

Model: ET3201L

Category: Touch screen monitors

Type: User manual

This manual is also suitable for

Elo TouchSystems ET3201L is an interactive digital signage touchmonitor that provides a natural flow of information between the user and the screen. With its Full HD resolution, built-in speakers, and headphone output, it's suitable for displaying graphics, videos, and presentations in various settings. The included computer modules transform the monitor into an all-in-one touchcomputer, making it ideal for interactive kiosks, retail displays, and corporate meeting rooms.

USER MANUAL

Elo Touch Solutions

ET3201L 32” Interactive Digital Signage Touchmonitor

ET4201L 42” Interactive Digital Signage Touchmonitor

ET5501L 55” Interactive Digital Signage Touchmonitor

ET7001L 70” Interactive Digital Signage Touchmonitor

SW601990 Rev E

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 2 of 36

No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated

into any language or computer language, in any form or by any means, including, but not limited to, electronic,

magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc.

Disclaimer

The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Afffiliates

(collectively "Elo") makes no representations or warranties with respect to the contents herein, and specifically

disclaims any implied warranties of merchantability or fitness for a particular purpose. Elo reserves the right to

revise this publication and to make changes from time to time in the content hereof without obligation of Elo to

notify any person of such revisions or changes.

Trademark Acknowledgments

AccuTouch, CarrollTouch, Elo, Elo (logo), Elo Touch, Elo Touch Solutions, Elo TouchSystems, IntelliTouch, iTouch,

SecureTouch, TouchTools and VuPoint are trademarks of Elo and its Affiliates. Windows is a trademark of Microsoft

Corporation.

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 3 of 36

Table of Contents

Chapter 1 – Introduction........................................................................... 4

Chapter 2 – Unpacking .............................................................................. 5

Chapter 3 – Touchmonitor Installation ................................................ 7

Chapter 4 – Mounting ................................................................................ 9

Chapter 5 – Operation ............................................................................... 13

Chapter 6 – Technical Support ............................................................... 28

Chapter 7 – Safety & Maintenance ........................................................ 29

Chapter 8 – Regulatory Information ................................................... 31

Chapter 9 – Warranty Information ......................................................... 35

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 4 of 36

Chapter 1: Introduction

Product Description

Your new Interactive Digital Signage (IDS) touchmonitor combines Elo Touch Solutions reliable

performance with the latest developments in touchscreen technology and display design. This

combination of features creates a natural flow of information between a user and the

touchmonitor.

This touchmonitor incorporates a 24-bit color, active matrix thin-film-transistor, and digital

signage LCD panel to provide superior display performance. Its Full HD resolution of

1920x1080 is suitable for displaying graphics and images. Other features that enhance this

LCD monitor’s performance are Plug & Play compatibility, built-in speakers and headphone

output capability, a remote for on screen display (OSD) controls, and a family of IDS computer

modules.

The computer modules are designed to slide into a bay on the rear of the monitor. The

monitors form factor will not be affected and extra cabling is not required. Your IDS

touchmonitor will turn into an IDS All-in-One touchcomputer.

Precautions

Follow all warnings, precautions and maintenance as recommended in this user manual to

maximize the life of your unit and prevent risks to user safety. See Chapter 8 for more

information on touchmonitor safety.

For your health and safety, it is strongly recommended that at least two people (four for the

ET7001L) handle, lift, and/or move these touchmonitors.

This manual contains information that is important for the proper setup and maintenance of the

IDS and optional computer module. Before setting up and powering on your new touchmonitor

and computer module, read through this manual, especially the Installation, Mounting, and

Operation chapters.

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 5 of 36

Chapter 2: Unpacking

Unpacking the Interactive Digital Signage Touchmonitor

To unpack the IDS, follow these steps:

1. The carton should be oriented in the manner according to its labeling. The hinged plastic

locks should be at the ‘bottom’.

2. Open and remove all 4 hinged plastic locks. There are 6 hinged plastic locks for the 7001L

unit.

3. Once the locks are removed, lift the cartons top lid off the bottom frame.

4. With the top lid removed, you now have access to the IDS touchmonitor and the included

accessories.

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 6 of 36

Chapter 3: IDS Touchmonitor Installation

Connector Panel & Interfaces

Note: For your health and safety, it is strongly recommended that at

least two people (four for the ET7001L) handle, lift, or move these

Touchmonitors. Elo recommends safe lifting techniques as described

in OSHA/NIOSH Guidelines.

Check that the following items are present and in good condition:

 IDS touchmonitor

 User Manual CD

 Quick Install Guide

 OSD Remote connected to the monitor

 Cables

o HDMI, USB, North America power, Europe/Korea power, U.K. power, Argentina power,

Taiwan power, China power, Korea power, Japan power, & Japan 3pin-2pin adapter

Remove the cable cover on the bottom rear (when viewed in landscape orientation) to access

the touchmonitors connector panel.

Pictures of the connector panel and interfaces. The OSD connection is in red.

3201L/4201L/5501L/7001L

Images of monitor back I/O ports with OSD remote

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 7 of 36

IDS Touchmonitor Connections to an External Computer

1. Connect the HDMI cable between the monitor and the video source.

2. Connect the USB touch cable between the monitor and the PC.

3. Select the correct power cable for your region. Connect it between the AC power source

and the touchmonitors POWER IN connector.

4. The touchmonitor ships in an ON state. Use the remote OSD to access the On Screen

Display Menu.

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 8 of 36

Installing the IDS Touchscreen Technology Software Drivers

IntelliTouch Plus units are HID compatible, but will require the Elo driver if touch calibration is

required.

Optical units are HID compatible and do not require an Elo touch driver. If an Elo touch driver

has previously been installed on the host computer, remove this driver by opening Control

Panel and selecting to remove the driver completely.

Visit the Elo Touch Solutions website www.elotouch.com for:

 Updates to the Elo touch driver

 Additional touch driver information

 Detailed touch driver installation guides

 Touch drivers for other operating systems

The Elo touch driver and the Elo Computer Module driver packs are available with the CD that

ships with the touchmonitor.

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 9 of 36

Chapter 4: Mounting

Note: For your health and safety, it is strongly recommended that at

least two people (four are recommended for the ET7001L) handle, lift,

or move these touchmonitors.

Note: When laying the display face-down (for attaching mounting

brackets or stands), protect the glass on the face from scratching and

damage. Lay the display on a non-abrasive surface, or first protect the

display face with film or foam.

General Mounting Information

The following three mounting orientations are supported: Landscape, portrait and table-top

mode. For optimal touch performance, ensure that the monitor is supported fully and is as

flat as possible.

Portrait

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 10 of 36

Landscape

Table Top –Refer to the Temperature Control section for table top mode requirements.

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 11 of 36

Rear VESA Mount

For the 32” and 42” models:

A four-hole, 400x400mm mounting pattern is provided on the rear of the monitor.

The VESA FDMI-compliant mounting is coded: VESA MOUNT PER MIS-F, 400,400,6MM

For the 55” models:

A four-hole, 600x600mm mounting pattern is provided on the rear of the monitor.

The VESA FDMI-compliant mounting is coded: VESA MOUNT PER MIS-F, 600,600,6MM

For the 70” models:

A four-hole, 400x400mm mounting pattern is provided on the rear of the monitor.

The VESA FDMI-compliant mounting is coded: VESA MOUNT PER MIS-F, 400,400,8MM

Refer to www.elotouch.com for dimensional drawings.

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 12 of 36

Optional Stand (for 3201L and 4201L Only) Elo PN: E455084

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 13 of 36

Chapter 5: Operation

Power

To turn the touchmonitor on or off, press the touchmonitor power button once. If a computer

module is installed, then the computer module will also turn on with the monitor.

To abruptly power off the computer module and touchmonitor, press and hold the touchmonitor

power button until the computer shuts off.

To gracefully shut down the computer module, follow the computer modules operating systems

normal power off procedure.

A Power Status LED is provided on the OSD Remote that functions according to the following

table:

Touchmonitor/Computer Module status LED status

OFF OFF

SLEEP BLINKING

ON ON

The system consumes low power when in SLEEP and OFF modes. For detailed power

consumption specifications, refer to technical specifications available on the Elo website

www.elotouch.com.

Touching the screen will bring the system out of MONITOR SLEEP mode.

If long periods of disuse are planned, unplug the AC power cable to save power.

The maximum voltage, frequency and current for the touchmonitor are provided in the power

ratings table below:

Operating Voltage

Range

Operating Frequency

Range

Operating Current

Range

ET32/4201L 100 - 240Vac 50/60 Hz 3.6 – 1.5 A

ET5501L 100 - 240Vac 50/60 Hz 5 – 2.1 A

ET7001L 100 - 240Vac 50/60 Hz 5 – 2.1 A

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 14 of 36

IntelliTouch Touchscreen Technology

The IntelliTouch and IntelliTouch Plus touchscreens can be re-calibrated to your displayed video

image, if needed, through the calibration function in the Elo driver control panel.

IntelliTouch Plus monitors require calibration if the video source is rotated.

Optical Touchscreens Technology

When connected to Windows 7 computers, the touchmonitor can report six simultaneous

touches.

Gesturing Images:

For IntelliTouch Plus screens, the following gestures are possible:

Single Touch Gestures and their Functions:

Swipe - The ability to swipe through from one picture to another or drag an icon

For IntelliTouch Plus and Optical screens the following gestures are possible:

Dual Touch Gestures and their Functions:

Swipe – The action of moving a finger across the screen.

- The ability to swipe through from one picture to another or drag an icon

Pinch-Zoom - Zoom into a picture

- Place two fingers on the screen and move them closer together to zoom in. Move your fingers

away from each other to zoom out.

Before zoom After zoom

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 15 of 36

Rotate – A picture can be rotated 360°

In addition to the above gestures, Optical units have the ability to pinch and zoom three different

pictures at the same time because six simultaneous touches are supported.

Video

An LCD panels native resolution is its width and height measured in number of pixels.

In almost all cases, an image displayed on an LCD monitor will look best when your computers

output resolution matches the LCD panels native resolution. See the display specifications on

the Elo website www.elotouch.com to find your touchmonitors native resolution. Operating in

other resolutions will degrade video performance and is not recommended.

For computer output resolutions at non-native resolutions, the monitor will scale the video to

panel’s native resolution. For smaller input video resolutions, this involves “stretching” the input

image in the X- and Y-dimensions to fit the panel. For larger input video resolutions, this

involves “compressing” the input image in the X- and Y-dimensions to fit the panel. An

unavoidable byproduct of the scaling algorithms is a loss of fidelity when the computers output

video image is scaled by the monitor to fit the display. This loss of fidelity is most apparent when

viewing feature-rich images at close distances (for example images containing small-font text).

Your touchmonitor will likely not require video adjustments. However, for analog VGA video,

variations in video graphic card outputs may require touchmonitor adjustments through the

OSD to optimize the quality of the touchmonitors displayed image. To reduce the need for

adjustments for different video mode timings, the monitor correctly scales and displays some of

the video industries most common video timing modes.

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 16 of 36

On-Screen Display (OSD) Connected Through the RJ45

Connection

Five OSD buttons can be found on the OSD remote. There is an LED light which shows the

current state of the monitor. The following are the functions that relate to the designated button.

The buttons and their functionality are:

Button Function when OSD is not displayed: Function when OSD is displayed:

Menu Display OSD main menu Return to previous OSD menu

Display OSD Audio source submenu

Decrease value of selected parameter /

select previous menu item

Hot key for changing video source*

Increase value of selected parameter /

select next menu item

Select Display Audio and Video Parameters Menu

Select parameter for adjustment /

select submenu to enter

Power for the monitor Toggles the power status of the monitor

*The hot key allows the user to quickly change the input video source. If the user accidently

presses this key, they can quickly press the Menu button to cancel a video source change.

Using the OSD buttons controls an on-screen graphical user interface which displays on top of

your input video, allowing intuitive adjustment of the following display parameters:

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 17 of 36

Parameter Available Adjustment

Main Menu

Video Settings, Audio Settings, Color Settings and Other Settings can be selected

Video Menu

Video Source, Brightness, Contrast, Black Level, Sharpness and Aspect Ratio are

available in this menu.

Video Source

Allows the user to switch between the available video sources.

Audio Menu

Allows the user to toggle the mute setting.

lso, the volume of the internal speakers or

headphones can be adjusted.

Default: Not Muted, Volume at 50

Color Menu

Displays the Color Adjust and Color Preference Menus

HDMI

Allows HDMI video to be displayed on the monitor

VGA Port

Allows VGA video to be displayed on the monitor

DisplayPort

Allows DisplayPort video to be displayed on the monitor

Elo Computer

Module

ECM DP – DisplayPort is the standard video output of Elo Computer modules. If

HDMI video input is found, the video source can be switched.

Video Source

The monitor continually scans for active video from VGA, DisplayPort, HDMI, and the

Computer Module. This adjustment selects which of those input ports should be

displayed.

If an Elo Computer Module or Intel OPS computer module has been detected, video

priority is given to the computer module before any of the external sources.

Brightness

Increase/decrease monitor brightness.

Default: 65

Contrast

Increase/decrease monitor contrast.

Default: 50

VGA Settings

Allows user to change the H. position, V. position, Clock and Phase.

If VGA is selected, the Auto-Adjust feature is available.

Sharpness

Adjusts sharpness of the displayed images.

Default: no sharpness adjustment

Sharpness function is disabled when the input source ratio is the same as the panels

native ratio

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 18 of 36

Aspect Ratio

Switches the scaling method between Fill Screen and Fill to Aspect Ratio.

Default: Fill Screen

Fill Screen – Scales the X- and Y-dimensions of the input video (up or down as

needed) to the displays native resolution.

Fill Aspect Ratio – Assuming a landscape orientation and an input video with aspect

ratio smaller than 16:9, scales the Y-dimension of the input video (up or down as

needed) to the displays Y-resolution, and scales the X-dimension to maintain the

aspect ratio (and fills the rest of the display with equal black bars on the left and right).

- When the input source ratio is the same as the panel native ratio, this function

is disabled

Direct output - Input source is the same with output source and the image will be on

the center of the screen. No Scaling will occur.

Recalibration may be required when switching between these options.

Light Sensor

The light sensor can be toggled on or off. When the light sensor is enabled, the

brightness cannot be changed manually.

Auto Adjust

utomatically adjusts the system clock to the input analog VGA video signal, affecting

the H-position, V-position, Clock, and Phase menu items.

Not applicable when using HDMI video or the Computer Module.

Clock

Allows fine adjustments of the panels pixel dot clock.

Not applicable when using HDMI/DisplayPort video or the Computer Module.

Phase

Allows fine adjustments of the panels pixel dot clock phase.

Not applicable when using HDMI/DisplayPort video or the Computer Module.

H-position

Moves the image horizontally on the display in single-pixel increments.

Default: centered.

Not applicable when using HDMI/DisplayPort video or the Computer Module.

V-position

Moves the image vertically on the display in single-pixel increments.

Default: centered.

Not applicable when using HDMI/DisplayPort video or the Computer Module.

Black Level

The user can choose between Standard, 5%, 10% or 15% black level offset.

The saturation level of the colors change according to the chosen black level offset.

Not available when the video source is from VGA.

Color

Temperature

Selects the displays color temperature. The available color temperatures are 9300K,

7500K, 6500K, 5500K, and User Defined. If the User Defined option is selected, the

user can change the color temperature by changing individual R, G, and B gains on a

scale from 0 to 100.

Default: User Defined with R, G, and B all set to 100.

Audio Source

Allows the user to choose the audio source. The choices are From Video Source, Line

in and ECM Line-in (available only if an ECM is detected)

If there is no Computer Module plugged in, and the video source is HDMI, the options

are: Line In and HDMI.

Default: Line In.

Color Adjust

The Color Temperature menu can be chosen or Hue and Saturation can be varied in

this menu.

Color Temperature will only be available in the Standard color preference mode. Hue

and Saturation are available in the remaining color preferences.

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 19 of 36

Color

Preference

Standard, Movie, Gaming, Photo modes can be chosen depending on the users

preference.

Movie, Gaming and Photo mode allow the user to vary the Hue and Saturation

Default: Standard

Other Menu

OSD menu: The Horizontal position, vertical position and OSD timer can be changed

from here.

Language Settings can be changed

Recall Defaults: set the system back to the preset standards

Information: display information about the monitor and system

MDC Protocol: allows the user to choose between DDC/CI and RS232 mode for the

MDC utility

Support & Help: Provide information about help and support

System Temperature: Provides the system Temperature information. If the Elo

computer module is inserted, there will be a secondary line showing that temperature

information.

OSD Timer

Adjusts how long a period of OSD button inactivity the Touchmonitor will wait before

closing the OSD. The adjustable range is between 5 and 60 seconds.

Default: 15 seconds

OSD

Language

Selects which language the OSD information is displayed in. The available

languages are: English, French, Italian, German, Spanish, Simplified Chinese,

Traditional Chinese, and Japanese.

Default: English.

OSD

H-Position

Moves the OSD location left and right on the display.

Default: 50 (centered)

OSD

V-position

Moves the OSD location up and down on the display.

Default: 50 (centered)

Recalling

Defaults

Selecting “Recall Defaults” restores all factory default settings for OSD-adjustable

parameters (except OSD Language and OSD Position) and for Preset Video Mode

timings.

MDC Protocol

This menu allows the user to switch between the serial protocol and the DDC/CI

protocol.

DDC/CI protocol is used to communicate to a host computer via the video signal.

Tabletop

Enables or disables the Tabletop Thermal Protection Mode settings

Information

Displays Monitor Information, System Temperature and Help & Support options.

Nothing is adjustable in this menu.

Monitor

Information

Displays the touchmonitor model and the monitor and touchscreen serial #

information

System

Temperature

Displays the real-time temperature of the Video Board

Note: Docking Board and the CPU Sensor temperatures are only available if these

features are supported by the computer module.

Help &

Support

Display information regarding Elo Touch Solutions contact information.

All touchmonitor adjustments made through the OSD are automatically memorized as soon as

they are entered. This feature saves you from having to reset your choices every time the

touchmonitor is unplugged or powered off and on or if there is a power failure.

User Manual: Interactive Digital Signage

SW601990 Rev E, Page 20 of 36

OSD and Power Lockouts

Press and hold the “Menu” and “>” buttons for two seconds to enable/disable the OSD Locking

feature. When the OSD Locking is enabled, pressing any of the Menu, Up, Down, or Select

keys will have no effect on the system.

Press and hold the “Menu” and “<” buttons for two seconds to enable/disable the Power

Locking feature. When the Power Locking is enabled, pressing the power switch will have no

effect on the system.

Audio

Audio from the touchmonitor Line In, touchmonitor HDMI, touchmonitor DisplayPort, computer

module Line In, or computer module HDMI or DisplayPort ports can be played over the

touchmonitors internal speakers. See the “Audio Source” OSD parameter for details. When

headphones are plugged into the headphone output jack, the internal speakers turn off and

audio is played over the headphones.

Volume and muting of the speaker and headphone outputs can be controlled by the OSD.

MDC Functionality (For Remote Monitor Applications)

The touchmonitor has the ability to allow remote access from a host application. This is done

through the use of the Multiple Display Control command sets. By installing the IDS Utilities

Suite, the user can communicate with the monitor via the application. The host application can

send a variety of different instructions which will be executed on the IDS 01 series touchmonitor.

For detailed information, refer to the utilities suite user guide.

RFID Functionality

For 3201L and 4201L Units:

There is an integrated RFID antenna within the monitor. To enable the RFID functionality, a

RFID reader module (available at www.elotouch.com) must be installed and connected to the

integrated monitor antenna. Refer to the RFID peripheral installation guide for proper hardware

and software installation techniques.

For the 5501L and 7001L units, an external peripheral kit is available from Elo.

The list of RFID protocols that can be read are:

 ISO-14443-A

 ISO-14443-B

 ISO-15693

The RFID features Peer-to-Peer applications and the Read and Write functionality.

Page is loading ...

Elo TouchSystems ET3201L User manual

Brand: Elo TouchSystems

Model: ET3201L

Category: Touch screen monitors

Type: User manual

This manual is also suitable for

Download PDF

report

Elo TouchSystems ET3201L User manual

This manual is also suitable for

Elo TouchSystems ET3201L User manual

Related papers

Other documents