2. Home
  3. Domestic appliances
  4. Climate control
  5. Split-system air conditioners
  6. Mitsubishi Electric
  7. PAC-SJ07SG-E
PAC-SJ07SG-E

Mitsubishi Electric PAC-SJ07SG-E User manual

  • Hello! I've reviewed the document for the MITSUBISHI ELECTRIC Air Outlet Guide PAC-SJ07SG-E, designed to control airflow direction for outdoor units. This guide helps to prevent short cycles and offers multiple discharge orientations. I understand the importance of proper installation and am ready to answer your questions about the specifications, compatibility, and usage of this product.
  • What is the purpose of the Air Outlet Guide?
    What are the possible air outlet directions?
    What should I be careful of when installing this guide?
    Does installing this guide affect the performance?
E-255
OPTIONAL
PARTS
A part to change air direction from outdoor unit. Can
also be used to prevent short cycles.
Figure
Specications
PUZ-ZM35VKA
PUZ-ZM50VKA PUHZ-ZRP35VKA2
PUHZ-ZRP50VKA2
1 piece required
Air Outlet Guide
PAC-SJ07SG-E
Descriptions
Applicable Models
Air Outlet Guide
507
Z
Z-Z
Z
4-φ5hole
465
106.8
55.8
14
480
462
554
571
48
52°
53.7 8×48(=384)
462
489.6
Dimensions Unit: mm
Alloy hot-dip zinc-coated carbon steel sheet/Acrylic resin coating
Ivory (3.0Y 7.8/1.1)
Air outlet direction
Color (Munsell)
Material/surface treatment
Weight 2.8kg
Changeable between up, down or sideways
Accessory name x Qty.
<Material/Surface treatment> Screw (M5x10) x 4 (Iron/Zinc nickel
alloy plated)
Screw (M4x12) x 4 (Iron/Zinc nickel
alloy plated)
Exterior
(to change air blowing direction)
* Air Guide prevents reverse rotation of outdoor unit fan when it enters low speed rotation mode with fan controller
being operated. It is also used for protection of fan when strong winds, such as a typhoon, wind blowing through tall
buildings, etc., directly strike the air outlet. In addition, installation of this product is necessary when cooling opetation
is to be performed in outdoor tempreture of -5℃ or lower (down to -15℃).
Note the followings when installing this guide:
1) Be sure not to use "upward discharge" in a place where snowing is possible. Snow may accumulate in the
guard, which could damage the fan, etc.
2) Attaching this unit will decrease the performance (by 2-3%) and increase noise from outdoor unit (by approx. 1-2 dB).
3) Do not use "upward discharge" when there are any obstacles at the back and on both sides of outdoor unit
(air is taken in from top of unit): This could cause a short cycle.
4) To eliminate the influence of external wind, be sure to install the unit with its back facing to wall.
5) Do not install this unit in a place where wind directly blows to the back of the unit.
CAUTION
When the outdoor unit is installed in front of a store or in a passage, this air outlet guide is used to change the discharge direction of
hot air (during cooling) or cold air (during heating) from the outdoor unit.
Upward, downward and sideways directions are possible. This guide is also effective to protect the
winds may blow against the discharge outlet.
[R410A type][R32 type]
E-256
OPTIONAL
PARTS
Air Outlet Guide to change air blowing directions PAC-SJ07SG-E
How to Use / How to Install
1　
Accesories
Make sure that this package has the following parts as well as the installation sheet:
Note that two sets of this product are necessary for ZM100, ZM125, ZM140　ZRP100, ZRP125, ZRP140.
2 　
Requirements of installation space
[Unit:mm]
●Secure the necessary surrounding space shown below and select a place with less obstacles, to prevent a short cycle.
1) Surrounding space needed when installing one unit
・Do not use "upward discharge" in cases of figures (3) and (5) below.
(1) Obstacle at front
(open at back, sides and top) (2) Obstacles at back and front
(open at sides and top) (3) Obstacles at back and top
(open at front and sides)
(4) Obstacles at back, and sides
(open at front and top) (5) Obstacles at back, sides
and top (open at front)
500 or more
500 or more 100 or more
500 or less
200 or more
1000 or more
200 or more
100 or more
350 or more
500 or less
300 or more
150 or more 350 or more
1000 or more
(1) Obstacle at front
(open at back, sides and top) (2) Obstacles at back and front
(open at sides and top)
(4) Installing units, one in each row (5) Installing multiple units in multiple rows
(3) Obstacles at back and top
(open at front and sides)
2) Surrounding space needed when installing multiple units
・When installing units horizontally in a series, leave at least 350 mm space between units .
・Do not use "upward discharge" in case of figure (3) below.
※Keep at least 1000 when using
outlet guide in directions other than
"upward discharge".
※Keep at least 2000 when using
outlet guide in directions other
than "upward discharge".
1000 or more
1000 or more
300 or more
300 or more
300 or less
1000 or more
（1500）
1000 or more
1000 or more
※Limit of 3 units can be installed horizontally
in series. When installing a larger number
of units, maintain the space between units
shown above.
1000 or more
1000 or more
300 or more
400 or more
100 or more
500 or more
500 or more
400 or more
1 2
2Support 3Attachment
screw 5×10
1Air outlet
guide 44Attachment
screw 4×12 4
E-257
OPTIONAL
PARTS
3　
Installation Complete Diagrams
4　
Installation Method
Air outlet guide
809W × 300D × 630H(mm)
Outdoor unit
<Setting blow-off direction>
Upward Downward Sideways to right
Sideways to left
(1) Make a frame by fixing 2 supports 2 on the outdoor unit with 4 screws 4.
(2) Fix the air outlet guide 1 to the supports mounted on the outdoor unit with 4 screws 3.
●Four blowout directions can be selected: Check the orientation of blowout vane, and attach the blowout guide in the direction that
matches the situation at local site.
4
3
2
1
Air Outlet Guide to change air blowing directions PAC-SJ07SG-E
/