Mitsubishi Electric PAC-SJ07SG-E User manual

Brand: Mitsubishi Electric

Model: PAC-SJ07SG-E

Category: Split-system air conditioners

Type: User manual

Mitsubishi Electric PAC-SJ07SG-E is an air outlet guide that allows you to change the air blowing direction of your outdoor unit. It can be used to prevent short cycles and protect the fan when the unit is installed in a location where strong winds may blow against the air outlet. This product can be used for both heating and cooling and is compatible with various Mitsubishi Electric models. It is easy to install and comes with all the necessary hardware.

E-255

OPTIONAL

PARTS

A part to change air direction from outdoor unit. Can

also be used to prevent short cycles.

Figure

Specications

PUZ-ZM35VKA

PUZ-ZM50VKA PUHZ-ZRP35VKA2

PUHZ-ZRP50VKA2

1 piece required

Air Outlet Guide

PAC-SJ07SG-E

Descriptions

Applicable Models

Air Outlet Guide

507

Z-Z

4-φ5hole

465

106.8

55.8

480

462

554

571

52°

53.7 8×48(=384)

462

489.6

Dimensions Unit: mm

Alloy hot-dip zinc-coated carbon steel sheet/Acrylic resin coating

Ivory (3.0Y 7.8/1.1)

Air outlet direction

Color (Munsell)

Material/surface treatment

Weight 2.8kg

Changeable between up, down or sideways

Accessory name x Qty.

<Material/Surface treatment> Screw (M5x10) x 4 (Iron/Zinc nickel

alloy plated)

Screw (M4x12) x 4 (Iron/Zinc nickel

alloy plated)

Exterior

(to change air blowing direction)

* Air Guide prevents reverse rotation of outdoor unit fan when it enters low speed rotation mode with fan controller

being operated. It is also used for protection of fan when strong winds, such as a typhoon, wind blowing through tall

buildings, etc., directly strike the air outlet. In addition, installation of this product is necessary when cooling opetation

is to be performed in outdoor tempreture of -5℃ or lower (down to -15℃).

Note the followings when installing this guide:

1) Be sure not to use "upward discharge" in a place where snowing is possible. Snow may accumulate in the

guard, which could damage the fan, etc.

2) Attaching this unit will decrease the performance (by 2-3%) and increase noise from outdoor unit (by approx. 1-2 dB).

3) Do not use "upward discharge" when there are any obstacles at the back and on both sides of outdoor unit

(air is taken in from top of unit): This could cause a short cycle.

4) To eliminate the influence of external wind, be sure to install the unit with its back facing to wall.

5) Do not install this unit in a place where wind directly blows to the back of the unit.

CAUTION

When the outdoor unit is installed in front of a store or in a passage, this air outlet guide is used to change the discharge direction of

hot air (during cooling) or cold air (during heating) from the outdoor unit.

Upward, downward and sideways directions are possible. This guide is also effective to protect the

winds may blow against the discharge outlet.

[R410A type][R32 type]

E-256

OPTIONAL

PARTS

Air Outlet Guide to change air blowing directions PAC-SJ07SG-E

How to Use / How to Install

Accesories

Make sure that this package has the following parts as well as the installation sheet:

Note that two sets of this product are necessary for ZM100, ZM125, ZM140　ZRP100, ZRP125, ZRP140.

Requirements of installation space

[Unit:mm]

●Secure the necessary surrounding space shown below and select a place with less obstacles, to prevent a short cycle.

1) Surrounding space needed when installing one unit

・Do not use "upward discharge" in cases of figures (3) and (5) below.

(1) Obstacle at front

(open at back, sides and top) (2) Obstacles at back and front

(open at sides and top) (3) Obstacles at back and top

(open at front and sides)

(4) Obstacles at back, and sides

(open at front and top) (5) Obstacles at back, sides

and top (open at front)

500 or more

500 or more 100 or more

500 or less

200 or more

1000 or more

200 or more

100 or more

350 or more

500 or less

300 or more

150 or more 350 or more

1000 or more

(1) Obstacle at front

(open at back, sides and top) (2) Obstacles at back and front

(open at sides and top)

(4) Installing units, one in each row (5) Installing multiple units in multiple rows

(3) Obstacles at back and top

(open at front and sides)

2) Surrounding space needed when installing multiple units

・When installing units horizontally in a series, leave at least 350 mm space between units .

・Do not use "upward discharge" in case of figure (3) below.

※Keep at least 1000 when using

outlet guide in directions other than

"upward discharge".

※Keep at least 2000 when using

outlet guide in directions other

than "upward discharge".

1000 or more

300 or more

300 or less

1000 or more

（1500）

1000 or more

※Limit of 3 units can be installed horizontally

in series. When installing a larger number

of units, maintain the space between units

shown above.

1000 or more

300 or more

400 or more

100 or more

500 or more

400 or more

1 2

2Support 3Attachment

screw 5×10

1Air outlet

guide 44Attachment

screw 4×12 4

E-257

OPTIONAL

PARTS

Installation Complete Diagrams

Installation Method

Air outlet guide

809W × 300D × 630H(mm)

Outdoor unit

Upward Downward Sideways to right

Sideways to left

(1) Make a frame by fixing 2 supports 2 on the outdoor unit with 4 screws 4.

(2) Fix the air outlet guide 1 to the supports mounted on the outdoor unit with 4 screws 3.

●Four blowout directions can be selected: Check the orientation of blowout vane, and attach the blowout guide in the direction that

matches the situation at local site.

Air Outlet Guide to change air blowing directions PAC-SJ07SG-E

Mitsubishi Electric PAC-SJ07SG-E User manual

Brand: Mitsubishi Electric

Model: PAC-SJ07SG-E

Category: Split-system air conditioners

Type: User manual

Download PDF

report

Mitsubishi Electric PAC-SJ07SG-E User manual

Mitsubishi Electric PAC-SJ07SG-E User manual

Related papers

Other documents