PAC BKTOYK969 is an installation kit used to mount a DIN or ISO aftermarket radio into select Toyota, Scion, and Lexus vehicles. This kit includes a DIN sleeve, ISO mount spacers, trim ring, and all necessary hardware.
The DIN sleeve allows you to mount a DIN-sized aftermarket radio into the vehicle's dash. The ISO mount spacers are used to mount an ISO-sized aftermarket radio into the vehicle's dash.
The trim ring can be used to fill the gap between the aftermarket radio and the vehicle's dash. The kit also includes all the necessary hardware to complete the installation.
PAC BKTOYK969 is an installation kit used to mount a DIN or ISO aftermarket radio into select Toyota, Scion, and Lexus vehicles. This kit includes a DIN sleeve, ISO mount spacers, trim ring, and all necessary hardware.
The DIN sleeve allows you to mount a DIN-sized aftermarket radio into the vehicle's dash. The ISO mount spacers are used to mount an ISO-sized aftermarket radio into the vehicle's dash.
The trim ring can be used to fill the gap between the aftermarket radio and the vehicle's dash. The kit also includes all the necessary hardware to complete the installation.
CUSTOMER HELP LINE
USA 800-323-4329 • Canada 800-245-8777
TOYK969 Mounting Kit
Toyota
2007-14 FJ CRUISER
2007-14 YARIS (Excluding radio w/2”x4” LCD display)
Scion
2004-06 xA
2004-14 xB
2008-14 xD
2005-10 TC
VEHICLE APPLICATIONS
iTOYK969
©2015 AMERICAN INTERNATIONAL INDUSTRIES, INC.
TECH Ver. 10/14 PRINT Ver. 04/15
WWW.AIUS.NET
2500 East Francis Street Ontario, CA 91761, U.S.A.
USA Sales (800) 336-6500
Canada Sales (888) 922-3006
For information about other American International automotive
accessories visit our website at:
http://www.aius.net
1
DIN MOUNT INSTRUCTIONS
1. Follow instructions from steps 1&2 of ISO mount instructions below.
2. Insert DIN sleeve from your new radio into the upper section of the installation kit.
(This DIN sleeve comes with all new radios and slides off the back of the radio)
3. Depress the tabs from inside the sleeves opening upward, outward, and downward
to secure sleeve to the installation kit.
4. Install radio into sleeve and lock into place.
Optional use Trim Ring (ITR-969) may be used on some radios if desired.
Due to the movement of some faces on some radios our ISO Trim Ring may not be able
to be used. You may also ISO mount your radio. Your new radio must have a trim ring
around the face of the radio that is designed to be easily removed. Consult your radio
ownerʼs manual.
ITR-969
Trim Ring
(Optional Use)
ISO MOUNT INSTALLATION INSTRUCTIONS
Not e: Some radio faces are larger in size than the ITR-969 Trim Ring allows.
You may need to file the Trim Ring opening larger for some radios.
1. Attach the left and right side brackets to the main bracket. See illustration below.
2. Attach left and right side brackets to the rear of the pocket using screws supplied w/kit.
3. Attach ISO Mount Spacers to the inside of upper section on
both Left & Right mounting brackets as shown in Figure A.
4. Slide radio into kit from rear & attach to ISO mounting
brackets using screws supplied with radio (do not tighten
screws at this time). (Be sure the length of the screws
DO NOT touch any electrical parts inside radio, some
screws may need to be shortened.)
5. Slide radio forward or backward for your desired look and
then tighten the mounting screws. Use ISO trim ring
when possible.
NOTE: Optional ISO trim ring (ITR-969 included)
may be used in place of after-market radioʼs
trim ring. For ISO mount applications,
mount after-market radio
to side brackets using
hardware included.
ITR-969
Trim Ring
(Optional Use)
Fig. A
DI
N
Sl
eev
e
10
1. Carefully unclip and remove the soft trim piece from around the radio, airbag
light/hazard button and passenger side air vent.
2. Carefully unclip and pry forward the radio trim bezel.
3. Remove the (4) Phillips screws securing the radio to the sub-dash.
4. Pull radio forward, disconnect the attached wire harness and antenna lead
and remove radio.
DASH DISASSEMBLY
2
012-14 TOYOTA YARIS
KIT ASSEMBLY
FOR ISO or DIN MOUNT APPLICATIONS SEE PAGE 1
REMOVE SHADED MOUNTING
TABS ON BOTH LEFT AND
RIGHT SIDES OF KIT
1. Prepare mounting brackets as shown below.
ATTACH BRACKETS TO REAR OF
POCKET USING SCREWS SUPPLIED
FOR ISO or DIN MOUNT APPLICATIONS SEE PAGE 1
KIT ASSEMBLY
KEEP SHADED MOUNTING TABS
ON BOTH LEFT AND RIGHT
BRACKETS.
REMOVE ALL OTHERS.
Optional use
I
TR 969
IMB 969L
IMB 969R
1. Prepare mounting brackets as shown below.
ATTACH BRACKETS TO REAR OF
POCKET USING SCREWS SUPPLIED
FOR ISO or DIN MOUNT APPLICATIONS SEE PAGE 1
KIT ASSEMBLY
REMOVE SHADED MOUNTING
TABS ON BOTH LEFT AND
RIGHT BRACKETS
Optional use
I
TR 969
IMB 969L
IMB 969R
2
1. Carefully pull outward on the left and right (rotary) climate control knobs
and remove the phillips screw from behind each knob.
2. Carefully unclip and remove the side trims from beside the climate
controls, ashtray, and pocket.
3. Remove the (2) phillips screws securing the lower edges of the climate control/radio
trim bezel to the sub-dash.
4. Carefully pry outward on the Climate control/radio trim bezel, disconnect all
harnesses and remove trim bezel.
5. Remove the (4) Phillips screws securing the factory radio to the sub-dash.
Carefully pull radio forward, disconnect the wire harness and antenna
lead from the radio and remove radio.
DASH DISASSEMBLY
2
004-06 TOYOTA SCION xA
9
1. Carefully unsnap the rectangle bezel surrounding the factory radio
2. Remove (4) 10mm bolts securing the factory radio in
3. Disconnect all harnesses and remove radio from dash
DASH DISASSEMBLY
2
008-14 TOYOTA SCION xB
3 8
1. Carefully pull outward on the left and right (rotary) climate control knobs and remove
the Phillips screw from behind each knob.
2. Starting from the bottom of the Radio/Climate control trim bezel, pull the left and right
side lower edges outward to release the lower clips.
3. Continue to pull the Radio/Climate control trim bezel outward and downward to
release the upper top clips.
4. Pull the Radio/Climate control trim bezel outward and disconnect all harnesses from
the rear of the bezel and remove bezel.
5. Remove the (4) Phillips screws securing the radio to the sub-dash.
6. Carefully pull the radio forward, disconnect the wire harness and antenna lead and
remove radio.
DASH DISASSEMBLY
2004-14 TOYOTA SCION xB
REMOVE SHADED MOUNTING
TABS ON BOTH LEFT AND
RIGHT BRACKETS
Optional use
I
TR 969
IMB 969L
IMB 969R
1. Prepare mounting brackets as shown below.
FOR ISO or DIN MOUNT APPLICATIONS SEE PAGE 1
KIT ASSEMBLY
1. Carefully unclip and remove the bottom edge trim piece from below the climate
control module.
2. Starting from lower edges, unclip the left and right side trims from around the radio
and climate controls and remove.
3. Carefully unclip and pry forward the lower edge of the instrument gauge trim bezel.
4. Carefully unclip and pull forward the Radio/Vent trim bezel, disconnect the attached
harness and remove bezel.
5. Remove the (4) Phillips screws securing the radio to the sub-dash.
6. Pull radio forward, disconnect the attached wire harness and antenna lead and
remove radio.
DASH DISASSEMBLY
2
007-11 TOYOTA YARIS - 4 DOOR SEDAN ONLY & 5 DOOR HATCHBACK
ITR 969
IMBY4-969L
IMBY4-969R
KIT ASSEMBLY
FOR ISO or DIN MOUNT APPLICATIONS SEE PAGE 1
REMOVE SHADED MOUNTING
TABS ON BOTH LEFT AND
RIGHT SIDES OF KIT
Note: Make sure you don’t break the bottom mounting tab
located between the two bottom tabs
ATTACH BRACKETS TO REAR OF
POCKET USING SCREWS SUPPLIED
KEEP THE 2 UNSHADED
MOUNTING TABS ON BOTH
LEFT AND RIGHT BRACKETS
1. There is a secondarily sub dash bezel between the main dash board
and the actual dash bezel.
2. Carefully remove the dash bezel starting at the top and work to the bottom
just above the climate controls
3. Unplug the necessary harness to remove bezel
4. Remove (4) Philips screws securing factory radio in place
5. Unplug radio harnesses and remove radio.
DASH DISASSEMBLY
2
008-14 TOYOTA SCION xD
5
1. Remove the individual Phillips screw from the lower edge of the thin trim pieces
located on the left and right side of the Radio/Climate control trim bezel, pry
outward and remove trim pieces.
2. Remove the (1) Phillips screw securing the left and right side of the Radio/Climate
control trim bezel.
3. Carefully pull the Radio/Climate control trim bezel forward, disconnect the attached
harnesses and remove trim bezel.
4. Remove the (4) 10mm bolts securing the radio to the sub-dash.
5. Pull radio forward, disconnect the wire harnesses and antenna lead and
remove radio.
DASH DISASSEMBLY
2
008-14 TOYOTA FJ CRUISER
ATTACH BRACKETS TO REAR OF
POCKET USING SCREWS SUPPLIED
REMOVE SHADED MOUNTING
TABS ON BOTH LEFT AND
RIGHT BRACKETS
Optional use
ITR 969
IMB 969L
IMB 969R
1. Prepare mounting brackets as shown below.
FOR ISO or DIN MOUNT APPLICATIONS SEE PAGE 1
KIT ASSEMBLY
6
ATTACH BRACKETS TO REAR OF
POCKET USING SCREWS SUPPLIED
REMOVE SHADED MOUNTING
TABS ON BOTH LEFT AND
RIGHT BRACKETS
Optional use
I
TR 969
IMB 969L
IMB 969R
1. Prepare mounting brackets as shown below.
FOR ISO or DIN MOUNT APPLICATIONS SEE PAGE 1
KIT ASSEMBLY
SECURE BRACKETS TO REAR
OF POCKET USING SCREWS
SUPPLIED WITH KIT
DASH DISASSEMBLY & RADIO REMOVAL INSTRUCTIONS
ITR 969
REMOVE SHADED MOUNTING BRACKETS
FOR TC APPLICATION
1. Set the parking brake.
2. Insert key into the ignition switch and turn to the on position
(DO NOT START THE CAR!!) then depress the brake pedal and place the shifter
lever into the low position.
3. Carefully pry upward on the center console trim from around the shifter, disconnect
the 12 Volt receptacle harness from the rear of the trim and remove trim.
4. Carefully pry Radio/Climate control trim bezel forward, starting at the bottom,
disconnect the harness attached to the rear of the Climate controls
and remove bezel.
5. Remove the (2) Phillips screws securing the lower factory radio brackets.
6. Remove the (2) 10 mm nuts securing the top radio mounting brackets.
7. Carefully pull radio forward, disconnect the harness or harnesses and antenna lead
from the rear of the radio, and remove radio.
8. Re-assemble dash in reverse order.
2
005-2010 TOYOTA SCION TC
TC
-
IM
B
969L
TC-
I
MB
969R
1. Prepare mounting brackets as shown below.
FOR ISO or DIN MOUNT APPLICATIONS SEE PAGE 1
KIT ASSEMBLY
4
I
TR 969
1. Starting from lower edges, unclip the left and right side trims from around the radio
and climate controls, disconnect the attached harnesses and remove trims.
2. Carefully unclip and pry forward the lower edge of the instrument gauge trim bezel.
3. Carefully unclip and pull forward the Radio/Vent trim bezel and remove.
4. Remove the (4) Phillips screws securing the radio to the sub-dash.
5. Pull radio forward, disconnect the attached wire harness and antenna lead and
remove radio.
DASH DISASSEMBLY
2
007-09 TOYOTA YARIS - 3 DOOR LIFTBACK ONLY
IMBY3-969L
IMBY3-969R
1. Prepare mounting brackets as shown below.
FOR ISO or DIN MOUNT APPLICATIONS SEE PAGE 1
KIT ASSEMBLY
REMOVE SHADED MOUNTING
TABS ON BOTH LEFT AND
RIGHT SIDES OF KIT
7
-
1
-
2
-
3
-
4
-
5
-
6
PAC BKTOYK969 is an installation kit used to mount a DIN or ISO aftermarket radio into select Toyota, Scion, and Lexus vehicles. This kit includes a DIN sleeve, ISO mount spacers, trim ring, and all necessary hardware.
The DIN sleeve allows you to mount a DIN-sized aftermarket radio into the vehicle's dash. The ISO mount spacers are used to mount an ISO-sized aftermarket radio into the vehicle's dash.
The trim ring can be used to fill the gap between the aftermarket radio and the vehicle's dash. The kit also includes all the necessary hardware to complete the installation.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
American International LXSK1315 User manual
-
American International TOYK994 User manual
-
American International NDK746 Owner's manual
-
Discount Car Stereo BKMBK100C Operating instructions
-
Metra 99-8300 Installation guide
-
American International GMK325BM User manual
-
Toyota 2007 Yaris Hatchback Owner's manual
-
Scosche TA2077B User manual
-
MB QUART Out of stockJS1-316 User manual
-
American International HYNK1133 User manual
