Knaack 47 Installation guide

Brand
Knaack
Model
47
Type
Installation guide

This manual is also suitable for

DANGER
IMPORTANT
BEFORE YOU BEGIN
Read these instructions and
warnings completely before
assembly.
ASSEMBLY AND INSTALLATION INSTRUCTIONS
STORAGEMASTER® Rolling Work Benches - Models 4547484950
PARTS LIST
1- Rolling Work Bench
1- Caster Set
1- Handle Kit
4- Drawers (Model 45 only)
0- Drawers (Model 47 only)
2- Drawers (Model 48 only)
8- Drawers & 1- Shelf (Model 49 only)
8- Drawers (Model 50 only)
CASTER BOLT KIT
16 5/16-18 x 3/4" Carriage Bolt
16 5/16-18 Whiz Lock Nut
16 1/4" Pushnut
HANDLE / LIFT KNOB KIT
1 - Push Handle
2 - Door Handle
6 - 5/16-18 x 3/4" Bolt, Truss hd.
4 - 5/16-18 Hex Whiz Nut
1 - Lift Knob
TOOLS REQUIRED
1/2" Open or Box End Wrench
1/2" Socket (3/8" drive)
Medium Extension (3/8" drive)
Ratchet Wrench (3/8" drive)
Torque Wrench (ft. lbs.)
Screwdriver, common
ASSEMBLY INSTRUCTIONS
1. Remove the caster box and handle kit
from the cabinet. Attach Handles to the
doors (Figure 1.). Attach the Push
Handle to the end.
WATCHMAN® III Lock System
IMPORTANT:
Carefully follow the separate instruc-
tions (see inside of door) which will guide
you to a proper lock installation.
Push Handle
5/16-18 x 3/4"
Truss Hd. Bolt
Door Handle
5/16-18 x 3/4"
Truss Hd. Bolt
5/16-18 Whiz
Lock Nut
Figure 1. Assembly View
WARNING
Black knob must be latched
in the closed position when
moving this product, so
doors and drawers do not
open on inclines, which can
cause serious personal
injury or property damage.
Caster Set Installation
2. Close the doors and lay the cabinet
on it's back, onto the flattened shipping
carton to prevent scratches (Figure 2.).
Mount the Swivel Casters on the end
you mounted the Handle. Insert a
Carriage bolt into a mounting hole, and
push a Pushnut onto the bolt to hold it
in place (Figure 3). Repeat this for the
other three mounting bolts. Place the
Caster over the bolts, then fasten with
Whiz Nuts. Repeat this for the remain-
ing Casters.
3.
Stand the unit upright. The Model 45
will now be complete. If you have a
Model 47 or are adding drawers to your
Model 45, read on.
Caster Brakes are not suitable
for keeping units in place when
transporting. Secure by another
method. Do not use casters on
rough or uneven surfaces. Do not
tow caster mounted boxes.
Do not put fuels, flammables, explosives or hazardous materials
inside these products.
Gasoline, solvents, gun powder or other munitions, dynamite,
propane, acetylene or other such products can explode if stored
inside these products.
Use these products ONLY for storing and transporting electric or
hand tools and equipment, and other similar materials.
Failure to follow these warnings or modification or other uses of
these products could result in death, serious injury or property
damage.
CAUTION
Part No. 14-4710 REV. L ECN 5285 03/13
If you have any ques
tions, please give us a call. Call
Toll Free 1-800-456-7865
KNAACK® products are protected by one or more of the following patents or trademarks : U.S. - 945736, 1182980, 5076078, 1266140, 1266140,
1266140, 1182982, 1182983, 1517767, 1560477, 1897535, 2290111, 5076078; Canada - 283281; U.K. - 2233036, 1390299, 2172510;
N.Z. - 296048, 296050; AUS - 754069, 754070 other patents or trademarks pending.
- NOTICE -
Any modification or unintended use of this product shall immediately void all manufacturers warranties.
Manufacturer disclaims all liability for injuries to persons or property resulting from any modification to, or
unintended use of this product.
Figure 2. Caster Mounting Holes
5/16-18
Whiz Nut
1/4"
Pushnut
5/16-18 x 3/4"
Carriage Bolt
Figure 3. Caster Mounting
Drawer Removal
and Installation
4. To remove a drawer (Figure 4.), pull
the drawer out till it stops. Notice the
locking levers located inside the track
that is attached to the drawer. Lift the left
lever (A) while pressing down on the right
lever (B). Pull drawer clear of the slides.
5. To replace a drawer, simply insert the
drawer slide into the cabinet slide and
close the drawer completely. The
mechanism will automatically latch.
Figure 4. Drawer Removal
Figure 5. Support Panel
#6 x 1/2"
Screw
Figure 6. Drawer Slide Installation
CAUTION
Pull out only one drawer at a
time to avoid sudden tipping
of product which could cause
serious personal injury or
property damage. For optimal
weight distribution of unit,
install larger drawers in lower
positions.
Drawer Slide Installation
6. The Drawer Support Panel (Figure 5.
Item A) has four wing nuts (B) that are
used to adjust the spring loaded panel.
Adjust these wing nuts as necessary to
obtain an approximate measurement of
17-13/16" between the left and right
support panels. It is important to mea-
sure across all four corners.
7. Figure your drawer arrangement
first. There are 15 possible "notches" for
drawer mounting in the following manner:
1" deep drawer requires 1 notch.
2" deep drawer requires 2 notches.
4-1/2" drawer requires 3 notches.
6" deep drawer requires 4 notches.
You can assemble any combination,
as long as you do not use more than
the 15 notches.
8.
Take one slide (Figure 6.) and insert
the clips (Inset) into the front and rear
notches of the drawer support panel.
Push the slide to the rear and down.
Secure the slide through the end access
hole in the slide.
9. With all slides installed, install the top
and bottom drawers and operate them a
few times. If they seem sluggish, further
adjustment to the wing nuts may be
required. Once the drawer action is
satisfactory, install the remaining
drawers.
Knaack LLC
ATTN: Warranty Claims
420 E. Terra Cotta
Avenue Crystal Lake, IL 60014
www.knaack.com
If you have any questions, please call toll free at 1-800-456-7865.
©201
3 Knaack LLC
Part No. 14-4710 REV. L ECN 5285 03/13
  • Page 1 1
  • Page 2 2

Knaack 47 Installation guide

Brand
Knaack
Model
47
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents